Infiniti F50. Manual — part 610
![](/vehicles/zatt/pasieses/thed/tellec.png)
REVERSE INTERLOCK DOOR MIRROR SYSTEM
GW-111
C
D
E
F
G
H
J
K
L
M
A
B
GW
Mirror Sensors Circuit Inspection
EIS0011N
1.
DOOR MIRROR FUNCTION INSPECTION
Check the following items.
●
Operation malfunction caused by a foreign object caught in door mirror face edge.
●
Operation malfunction in memory control
NOTE:
If a door mirror face position is set to an implausible angle, the set position may not be reproduced.
OK or NG?
OK
>> GO TO 2.
NG
>> Repair the malfunctioning parts, and check the symptom again.
2.
MIRROR SENSOR INSPECTION
With CONSULT–II
Check that "ON" is displayed on “MIR/SE RH R-L ”, “MIR/
SE RH U-D ” or “MIR/SE LH R-L ”, “MIR/SE LH U-D ” in the
DATA MONITOR. Refer to
.
NOTE:
It CONSULT-II is not available, skip this procedure and go to the next
step.
Question
OK
>> System is OK.
NG
>> GO TO 3.
3.
MIRROR SENSOR POWER SUPPLY INSPECTION
1.
Turn ignition switch ON.
2.
Check voltage between door mirror control unit connector D5 (deiver side), D35 (passenger side) terminal
1 and ground.
OK or NG
OK
>> GO TO 4
NG
>> Replace door mirror control unit.
PIIB0342E
1 (W/L) – Ground
:Approx. 5V
PIIA4604E
![](/vehicles/zatt/pasieses/thed/wererinere.png)
GW-112
REVERSE INTERLOCK DOOR MIRROR SYSTEM
4.
MIRROR SENSOR GROUND CIRCUIT INSPECTION
1.
Turn ignition switch OFF.
2.
Check continuity between door mirror control unit connector D5 (deiver side), D35 (passenger side) termi-
nal 2 and ground.
OK or NG
OK
>> GO TO 5
NG
>> Replace door mirror control unit.
5.
HARNESS CONTINUITY INSPECTION 1
1.
Disconnect door mirror control unit connector D5 (driver side), D35 (passenger side) and door mirror con-
nector D2 (driver side), D32 (passenger side).
2.
Check continuity between door mirror control unit connector D5
(driver side), D35 (passenger side) terminal 1, 2 and door mirror
connector D2 (driver side), D32 (passenger side) terminal 10,
16.
OK or NG
OK
>> GO TO 6
NG
>> Repair or replace harness.
6.
HARNESS CONTINUITY INSPECTION 2
1.
Disconnect door mirror control unit connector D5 (driver side), D35 (passenger side) and door mirror con-
nector D2 (driver side), D32 (passenger side).
2.
Check continuity between door mirror control unit connector D5 (driver side), D35 (passenger side) termi-
nals 5, 6 and door mirror connector D2 (driver side), D32 (passenger side) terminals 12, 14.
3.
Check continuity between door mirror control unit connector D5
(driver side), D35 (passenger side) terminals 5, 6 and ground.
OK or NG?
OK
>> GO TO 7.
NG
>> Repair or replace harness.
2 (Y) – Ground
:Continuity should exist.
PIIA4605E
1 (W/L) – 16 (W/L)
:Continuity should exist.
2 (Y) – 10 (Y)
:Continuity should exist.
PIIA4606E
5 (L/Y) – 14 (L/Y)
:Continuity should exist.
6 (G) – 12 (G)
:Continuity should exist.
5 (L/Y) – Ground
:Continuity should not exist.
6 (G) – Ground
:Continuity should not exist.
PIIA3540E
![](/vehicles/zatt/pasieses/thed/ras.png)
REVERSE INTERLOCK DOOR MIRROR SYSTEM
GW-113
C
D
E
F
G
H
J
K
L
M
A
B
GW
7.
MIRROR SENSOR SIGNAL INSPECTION
1.
Connect door mirror control unit D5 (driver side), D35 (passenger side) and door mirror D2 (driver side),
D32 (passenger side) connectors.
2.
Turn ignition switch ON.
3.
Check voltage between door mirror control unit connector D5 (driver side), D35 (passenger side) termi-
nals 5, 6and ground.
OK or NG?
OK
>> Replace the door mirror control unit.
NG
>> Replace the door mirror.
Con-
nector
Terminals (Wire color)
Condition
Voltage [V]
(Approx.)
(+)
(–)
D5
D35
5(L/Y)
Ground
When motor is
activated
(UP/ DOWN)
Changes between
4 (close to peak) – and
0.5 (close to valley)
6(G)
When motor is
activated
(LEFT/ RIGHT)
Changes between
4 (close to right edge) – and
0.5 (close to left edge)
PIIA3541E
![](/vehicles/zatt/pasieses/thed/ckin.png)
GW-114
DOOR MIRROR
DOOR MIRROR
PFP:96301
Removal and Installation
EIS000OE
NOTE:
Be careful not to damage the mirror bodies.
REMOVAL
1.
Remove the front door finisher and door sash cover. Refer to
EI-30, "Removal and Installation"
.
2.
Remove the door mirror harness connector.
3.
Loosen the door mirror mounting nuts, and remove the door mirror assembly.
INSTALLATION
Install in the reverse order of removal.
PIIA0046E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст