Infiniti I35 (A33). Manual — part 146
SBR035F
Removal and Installation
NHBR0299
REMOVAL
NHBR0299S01
1.
Remove the instrument lower driver panel. Refer to INSTRU-
MENT LOWER DRIVER PANEL, BT-30.
2.
Push the VDC OFF switch’s pawls and remove the switch from
the instrument lower driver panel.
INSTALLATION
NHBR0299S02
Installation is the reverse order of removal.
GI
MA
EM
LC
EC
FE
AT
AX
SU
ST
RS
BT
HA
SC
EL
IDX
VDC OFF SWITCH
VDC
Removal and Installation
BR-169
NHBR0199
CAUTION:
Be careful not to damage sensor edge and sensor rotor teeth.
When removing the front or rear wheel hub assembly, first
remove the ABS wheel sensor from the assembly. Failure to
do so may result in damage to the sensor wires making the
sensor inoperative.
Wheel Sensors
NHBR0199S01
SBR921C
SBR984C
SBR873CA
Sensor Rotor
NHBR0199S02
REMOVAL
NHBR0199S0201
1.
Remove the drive shaft and rear wheel hub. Refer to “Drive
Shaft” and “Wheel Hub” in AX section.
2.
Remove the sensor rotor using suitable puller, drift and bear-
ing replacer.
REMOVAL AND INSTALLATION
TCS/VDC
BR-170
SBR985C
INSTALLATION
NHBR0199S0202
Install the sensor rotor. For front sensor rotor, use hammer and
wooden block. For rear sensor rotor, use suitable drift and press.
I
Always replace sensor rotor with new one.
SBR986C
I
Pay attention to the dimension of rear sensor rotor as show in
figure.
h: 12.5 - 13.5 mm (0.492 - 0.531 in)
GI
MA
EM
LC
EC
FE
AT
AX
SU
ST
RS
BT
HA
SC
EL
IDX
REMOVAL AND INSTALLATION
TCS/VDC
Sensor Rotor (Cont’d)
BR-171
General Specifications
NHBR0200
Unit: mm (in)
Front brake
Brake model
CLZ25VD disc brake
Cylinder bore diameter
57.2 (2.252)
Pad
Length
×
width
×
thickness
125.6
×
46
×
9.5
(4.94
×
1.81
×
0.374)
Rotor outer diameter
×
thickness
296
×
24 (11.65
×
0.94)
Rear brake
Brake model
CL9HE disc brake
Cylinder bore diameter
33.96 (1.3370)
Pad
Length
×
width
×
thickness
89.1
×
39.5
×
10
(3.508
×
1.555
×
0.39)
Rotor outer diameter
×
thickness
278
×
9 (10.94
×
0.35)
Master cylinder
Cylinder bore diameter
23.81 (15/16)
Brake booster
Booster model
M215T
Diaphragm diameter
Primary
230 (9.06)
Secondary
205 (8.07)
Recommended brake fluid
DOT 3
Disc Brake
NHBR0201
Unit: mm (in)
Brake model
CLZ25VD
CL9HE
Pad wear limit
Minimum thickness
2.0 (0.079)
1.5 (0.059)
Rotor repair limit
Maximum runout
0.07 (0.0028)
0.07 (0.0028)
Minimum thickness
22.0 (0.866)
8.0 (0.315)
Brake Pedal
NHBR0202
Unit: mm (in)
Free height “H”*
167 - 174 (6.57 - 6.85)
Clearance “C” between pedal stopper and threaded end of stop lamp switch or ASCD switch
0.74 - 1.96 (0.0291 - 0.0772)
*: Measured from surface of dash reinforcement panel to surface of pedal pad
Parking Brake
NHBR0203
Control type
Foot lever
Number of notches
[under force of 196 N (20 kg, 44 lb)]
4 - 5
Number of notches
when warning lamp switch comes on
1
Brake Booster
NHBR0205
Unit: mm (in)
Output rod length
10.275 - 10.525 (0.4045 - 0.4144)
Clevis length (Dimension “A”)
130 (5.12)
ABS Wheel Sensor
NHBR0206
Clearance
Front
0.273 - 0.925 mm (0.0107 - 0.0364 in)
Rear
0.385 - 0.973 mm (0.0152 - 0.0383 in)
SERVICE DATA AND SPECIFICATIONS (SDS)
General Specifications
BR-172
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст