Infiniti I35 (A33). Manual — part 98
OUTPUT SHAFT ADJUSTING SHIMS
NHAT0194S03
Thickness
mm (in)
Part number*
0.80 (0.0315)
0.84 (0.0331)
0.88 (0.0346)
0.92 (0.0362)
0.96 (0.0378)
1.00 (0.0394)
1.04 (0.0409)
1.08 (0.0425)
1.12 (0.0441)
1.16 (0.0457)
1.20 (0.0472)
31438-80X60
31438-80X61
31438-80X62
31438-80X63
31438-80X64
31438-80X65
31438-80X66
31438-80X67
31438-80X68
31438-80X69
31438-80X70
*: Always check with the Parts Department for the latest parts information.
Bearing Retainer
NHAT0195
SEAL RING CLEARANCE
NHAT0195S01
Bearing retainer seal ring clearance
mm
(in)
Standard
0.10 - 0.30 (0.0039 - 0.0118)
Allowable limit
0.30 (0.0118)
Total End Play
NHAT0196
Total end play
mm (in)
0.25 - 0.55 (0.0098 - 0.0217)
BEARING RACE FOR ADJUSTING TOTAL END PLAY
NHAT0196S01
Thickness
mm (in)
Part number*
0.8 (0.031)
1.0 (0.039)
1.2 (0.047)
1.4 (0.055)
1.6 (0.063)
1.8 (0.071)
2.0 (0.079)
0.9 (0.035)
1.1 (0.043)
1.3 (0.051)
1.5 (0.059)
1.7 (0.067)
1.9 (0.075)
31435-80X00
31435-80X01
31435-80X02
31435-80X03
31435-80X04
31435-80X05
31435-80X06
31435-80X09
31435-80X10
31435-80X11
31435-80X12
31435-80X13
31435-80X14
*: Always check with the Parts Department for the latest parts information.
Reverse Clutch End Play
NHAT0197
Reverse clutch end play
mm (in)
0.55 - 0.90 (0.0217 - 0.0354)
THRUST WASHERS FOR ADJUSTING REVERSE CLUTCH DRUM END PLAY
NHAT0197S01
Thickness
mm (in)
Part number*
0.80 (0.0315)
0.95 (0.0374)
1.10 (0.0433)
1.25 (0.0492)
1.40 (0.0551)
1.55 (0.0610)
1.70 (0.0669)
1.85 (0.0728)
31508-80X13
31508-80X14
31508-80X15
31508-80X16
31508-80X17
31508-80X18
31508-80X19
31508-80X20
*: Always check with the Parts Department for the latest parts information.
GI
MA
EM
LC
EC
FE
AX
SU
BR
ST
RS
BT
HA
SC
EL
IDX
SERVICE DATA AND SPECIFICATIONS (SDS)
Output Shaft (Cont’d)
AT-389
Removal and Installation
NHAT0198
Unit: mm (in)
Distance between end of converter housing and torque converter
14 (0.55)
Shift Solenoid Valves
NHAT0264
Gear position
1
2
3
4
Shift solenoid valve A
ON (Closed)
OFF (Open)
OFF (Open)
ON (Closed)
Shift solenoid valve B
ON (Closed)
ON (Closed)
OFF (Open)
OFF (Open)
Solenoid Valves
NHAT0265
Solenoid valves
Resistance (Approx.)
Ω
Terminal No.
Shift solenoid valve A
20 - 30
2
Shift solenoid valve B
5 - 20
1
Overrun clutch solenoid valve
20 - 30
3
Line pressure solenoid valve
2.5 - 5
4
Torque converter clutch solenoid valve
5 - 20
5
A/T Fluid Temperature Sensor
NHAT0266
Remarks: Specification data are reference values.
Monitor item
Condition
Specification (Approximately)
A/T fluid temperature
sensor
Cold [20°C (68°F)]
"
Hot [80°C (176°F)]
1.5V
"
0.5V
2.5 k
Ω
"
0.3 k
Ω
Revolution Sensor (For Speed Sensor)
NHAT0267
Condition
Judgement
standard
When moving at 20 km/h (12 MPH), use the CONSULT-II pulse frequency measuring function.*1
CAUTION:
Connect the diagnosis data link cable to the vehicle diagnosis connector.
*1: A circuit tester cannot be used to test this item.
450 Hz (Approx.)
When vehicle parks.
0V
Dropping Resistor
NHAT0268
Resistance
Approx. 12
Ω
Power Train Revolution Sensor
NHAT0271
Condition
Judgement
standard
When moving at 20 km/h (12 MPH), use the CONSULT-II pulse frequency measuring function.*1
CAUTION:
Connect the diagnosis data link cable to the vehicle diagnosis connector.
*1: A circuit tester cannot be used to test this item.
240 Hz (Approx.)
When vehicle parks.
Under 1.3V or over 4.5V
SERVICE DATA AND SPECIFICATIONS (SDS)
Removal and Installation
AT-390
FRONT & REAR AXLE
CONTENTS
FRONT AXLE . . . . . . . . . . . . . . . . ..2
Precautions . . . . . . . . . . . . . . . . ..2
. . . . . . . . . . . . . . .2
Preparation . . . . . . . . . . . . . . . . ..2
. . . . . . . . . . 2
. . . . . . . . 2
Noise, Vibration and Harshness (NVH)
Troubleshooting . . . . . . . . . . . . . . ...3
. . . . . . . 3
On-vehicle Service. . . . . . . . . . . . . ...3
. . . . . . . . . . . . 3
. . . . . . . . . . .4
. . . . . . . . . . . . . . ...4
Wheel Hub and Knuckle. . . . . . . . . . . ..5
. . . . . . . . . . . . . . .5
. . . . . . . . . . . . . . . . .5
. . . . . . . . . . . . . . ..6
. . . . . . . . . . . . . . ..7
. . . . . . . . . . . . . . . .8
. . . . . . . . . . . . . . . ...8
Drive Shaft . . . . . . . . . . . . . . . . ...9
. . . . . . . . . . . . . . .9
. . . . . . . . . . . . . . . ...10
. . . . . . . . . . . . . . 11
. . . . . . . . . . . . . . 11
. . . . . . . . . . . . . . ...13
. . . . . . . . . . . . . . . .13
Service Data and Specifications (SDS). . . . . .15
. . . . . . . . . . . . . . .15
. . . . . . . . . .16
REAR AXLE. . . . . . . . . . . . . . . . ...17
Precautions . . . . . . . . . . . . . . . . 17
. . . . . . . . . . . . . ...17
Preparation . . . . . . . . . . . . . . . . 17
. . . . . . . . . ..17
. . . . . . . ..17
Noise, Vibration and Harshness (NVH)
Troubleshooting . . . . . . . . . . . . . . .18
On-vehicle Service. . . . . . . . . . . . . .18
. . . . . . . . . . .18
Wheel Hub . . . . . . . . . . . . . . . . .19
. . . . . . . . . . . . . ...19
. . . . . . . . . . . . . . . ...19
. . . . . . . . . . . . . . 20
Service Data and Specifications (SDS). . . . . .22
. . . . . . . . . ...22
GI
MA
EM
LC
EC
FE
AT
SU
BR
ST
RS
BT
HA
SC
EL
IDX
SBR686C
Precautions
PRECAUTIONS
NHAX0001
I
When installing rubber parts, final tightening must be car-
ried out under unladen condition* with tires on ground.
*: Fuel, radiator coolant and engine oil full. Spare tire, jack,
hand tools and mats in designated positions.
I
After installing removed suspension parts, check wheel
alignment and adjust if necessary.
I
Use flare nut wrench when removing or installing brake
tubes.
I
Always torque brake lines when installing.
Preparation
SPECIAL SERVICE TOOLS
NHAX0002
The actual shapes of Kent-Moore tools may differ from those of special service tools illustrated here.
Tool number
(Kent-Moore No.)
Tool name
Description
HT72520000
(J25730-B)
Ball joint remover
NT146
Removing tie-rod outer end and lower ball joint
KV38106700
(J34296)
KV38106800
(J34297)
Differential side oil seal
protector
NT147
Installing drive shaft
LH: KV38106700 (J34296)
RH: KV38106800 (J34297)
COMMERCIAL SERVICE TOOLS
NHAX0003
Tool name
Description
1 Flare nut crowfoot
2 Torque wrench
NT360
Removing and installing each brake piping
a: 10 mm (0.39 in)
FRONT AXLE
Precautions
AX-2
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст