Infiniti I35 (A33). Manual — part 86
![](/vehicles/zatt/ltherawowha/yose/gin.png)
SAT203D
9.
Install drive plates, driven plates, retaining plate and dish plate
for forward clutch.
I
Take care with order of plates.
10. Install snap ring for forward clutch.
SAT228D
11. Measure clearance between forward clutch retaining plate and
snap ring.
If not within allowable limit, select proper retaining plate.
Specified clearance:
Standard 0.45 - 0.85 mm (0.0177 - 0.0335 in)
Allowable limit 1.85 mm (0.0728 in)
Forward clutch retaining plate:
Refer to SDS, AT-384.
SAT123F
12. Check operation of forward clutch.
Refer to “DISASSEMBLY”, “Forward Clutch and Overrun
Clutch”, AT-336.
13. Check operation of overrun clutch.
Refer to “DISASSEMBLY”, “Forward Clutch and Overrun
Clutch”, AT-336.
Low & Reverse Brake
COMPONENTS
NHAT0157
SAT846K
GI
MA
EM
LC
EC
FE
AX
SU
BR
ST
RS
BT
HA
SC
EL
IDX
REPAIR FOR COMPONENT PARTS
Forward and Overrun Clutches (Cont’d)
AT-341
![](/vehicles/zatt/ltherawowha/yose/feevelloup.png)
SAT147F
DISASSEMBLY
NHAT0158
1.
Check operation of low & reverse brake.
a.
Apply compressed air to oil hole of transmission case.
b.
Check to see that retaining plate moves to snap ring.
c.
If retaining plate does not contact snap ring:
I
D-ring might be damaged.
I
Fluid might be leaking past piston check ball.
SAT149F
2.
In order to remove piston, apply compressed air to oil hole of
retainer while holding piston.
I
Apply air gradually and allow piston to come out evenly.
SAT150F
3.
Remove D-rings from piston.
INSPECTION
NHAT0159
Low and Reverse Brake Snap Ring, Spring Retainer
and Return Springs
NHAT0159S01
I
Check for deformation, fatigue or damage.
If necessary, replace.
I
When replacing spring retainer and return springs,
replace them as a set.
SAT162D
Low and Reverse Brake Drive Plate
NHAT0159S02
I
Check facing for burns, cracks or damage.
I
Measure thickness of facing.
Thickness of drive plate:
Standard value 1.8 mm (0.071 in)
Wear limit 1.6 mm (0.063 in)
I
If not within wear limit, replace.
REPAIR FOR COMPONENT PARTS
Low & Reverse Brake (Cont’d)
AT-342
![](/vehicles/zatt/ltherawowha/yose/ageve.png)
SAT150F
ASSEMBLY
NHAT0160
1.
Install D-rings on piston.
I
Apply ATF to both parts.
SAT323F
2.
Set and align piston with retainer.
I
This operation is required in order to engage the protru-
sions of piston to return springs correctly.
Further procedures are given in “ASSEMBLY”.
SAT923H
3.
Install driven plates, drive plates, retaining plate and dish plate
on transmission case.
I
Take care with order of plates and direction of dish plate.
SAT546G
4.
Install snap ring.
SAT155F
5.
Measure clearance between driven plate and transmission
case. If not within allowable limit, select proper retaining plate.
(front side)
Specified clearance:
Standard 1.7 - 2.1 mm (0.067 - 0.083 in)
Allowable limit 3.3 mm (0.130 in)
Retaining plate:
Refer to SDS, AT-385.
GI
MA
EM
LC
EC
FE
AX
SU
BR
ST
RS
BT
HA
SC
EL
IDX
REPAIR FOR COMPONENT PARTS
Low & Reverse Brake (Cont’d)
AT-343
Rear Internal Gear, Forward Clutch Hub and
Overrun Clutch Hub
COMPONENTS
NHAT0161
SAT975H
SAT157F
DISASSEMBLY
NHAT0162
1.
Remove overrun clutch hub and thrust washer from forward
clutch hub.
SAT251D
2.
Remove forward clutch hub from rear internal gear.
REPAIR FOR COMPONENT PARTS
Rear Internal Gear, Forward Clutch Hub and Overrun Clutch Hub
AT-344
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст