Infiniti G37 Coupe. Manual — part 894
![](/vehicles/zatt/keash/ckiif/ite.png)
CHASSIS MAINTENANCE
MA-29
< ON-VEHICLE MAINTENANCE >
C
D
E
F
G
H
I
J
K
L
M
B
MA
N
O
A
• Regarding spare tire (for emergency) wheel, wrong assembly pro-
tection pin through hole (1) has been set in addition to regular bolt
holes (2) in order to enable installation to front wheel.
NOTE:
Protection pin through hole of 18 inch spare wheel is non-through
type.
BRAKE FLUID LEVEL AND LEAKS
BRAKE FLUID LEVEL AND LEAKS : Inspection
INFOID:0000000001679258
• If fluid level is extremely low, check brake system for leaks.
BRAKE LINES AND CABLES
BRAKE LINES AND CABLES : Inspection
INFOID:0000000001679259
• Check brake fluid lines and parking brake cables for improper
attachment, leaks, chafing, abrasions, deterioration, etc.
BRAKE FLUID
BRAKE FLUID : Changing
INFOID:0000000001679260
1.
Drain brake fluid from each bleed valve.
2.
Refill until new brake fluid comes out from each bleed valve.
Use same procedure as in bleeding hydraulic system to refill
brake fluid.
Refer to
BR-12, "Bleeding Brake System"
• Refill with recommended Genuine NISSAN Super Heavy Duty
Brake Fluid or equivalent DOT 3 (US FMVSS No. 116).
Refer to
MA-10, "Fluids and Lubricants"
• Never reuse drained brake fluid.
• Be careful not to splash brake fluid on painted areas.
DISC BRAKE
JPEIC0029ZZ
SBR451D
SBR389C
SBR419C
![](/vehicles/zatt/keash/ckiif/ovi.png)
MA-30
< ON-VEHICLE MAINTENANCE >
CHASSIS MAINTENANCE
DISC BRAKE : Inspection
INFOID:0000000001679261
DISC ROTOR
Check condition, wear, and damage.
CALIPER
• Check for leakage.
BRAKE PAD
• Check for wear or damage.
DISC BRAKE : Front Disc Brake
INFOID:0000000001766473
1 PISTON TYPE
Unit: mm (in)
4 PISTON TYPE
Unit: mm (in)
DISC BRAKE : Rear Disc Brake
INFOID:0000000001766474
1 PISTON TYPE
SMA922A
BRA0010D
Brake pad
Standard thickness
10.3 (0.406)
Wear limit thickness
2.0 (0.079)
Disc rotor
Standard thickness
32.0 (1.260)
Wear limit thickness
30.0 (1.181)
Thickness variation (measured at 8 positions)
0.015 (0.0006)
Runout limit (with it attached to the vehicle)
0.035 (0.0014)
Brake pad
Standard thickness
11.0 (0.433)
Wear limit thickness
2.0 (0.079)
Disc rotor
Standard thickness
32.0 (1.260)
Wear limit thickness
30.0 (1.181)
Thickness variation (measured at 8 positions)
0.015 (0.0006)
Runout limit (with it attached to the vehicle)
0.035 (0.0014)
![](/vehicles/zatt/keash/ckiif/cre.png)
CHASSIS MAINTENANCE
MA-31
< ON-VEHICLE MAINTENANCE >
C
D
E
F
G
H
I
J
K
L
M
B
MA
N
O
A
Unit: mm (in)
2 PISTON TYPE
Unit: mm (in)
STEERING GEAR AND LINKAGE
STEERING GEAR AND LINKAGE : Inspection
INFOID:0000000001679264
STEERING GEAR
• Check gear housing and boots for looseness, damage and grease
leakage.
• Check connection with steering column for looseness.
STEERING LINKAGE
Check ball joint, dust cover and other component parts for looseness, wear, damage and grease leakage.
POWER STEERING FLUID AND LINES
POWER STEERING FLUID AND LINES : Inspection
INFOID:0000000001679265
Check fluid level in reservoir tank with engine off.
Use “HOT” range at fluid temperatures of 50 to 80
°
C (122 to 176
°
F)
or “COLD” range at fluid temperatures of 0 to 30
°
C (32 to 86
°
F).
CAUTION:
• Do not overfill.
• Recommended fluid is Genuine NISSAN PSF or equivalent.
Refer to
MA-10, "Fluids and Lubricants"
.
Brake pad
Standard thickness
8.5 (0.335)
Wear limit thickness
2.0 (0.079)
Disc rotor
Standard thickness
16.0 (0.631)
Wear limit thickness
15.0 (0.591)
Thickness variation (measured at 8 positions)
0.015 (0.0006)
Runout limit (with it attached to the vehicle)
0.055 (0.0022)
Brake pad
Standard thickness
8.5 (0.335)
Wear limit thickness
2.0 (0.079)
Disc rotor
Standard thickness
20.0 (0.787)
Wear limit thickness
18.0 (0.709)
Thickness variation (measured at 8 positions)
0.015 (0.0006)
Runout limit (with it attached to the vehicle)
0.055 (0.0022)
SLIA0014E
SST850C
![](/vehicles/zatt/keash/ckiif/ost.png)
MA-32
< ON-VEHICLE MAINTENANCE >
CHASSIS MAINTENANCE
• Check lines for improper attachment, leaks, cracks, damage,
loose connections, chafing and deterioration.
• Check rack boots for accumulation of power steering fluid.
AXLE AND SUSPENSION PARTS
AXLE AND SUSPENSION PARTS : Inspection
INFOID:0000000001679266
Check front and rear axle and suspension parts for excessive play,
cracks, wear or other damage.
• Shake each wheel to check for excessive play.
• Check wheel bearings for smooth operation.
• Check axle and suspension nuts and bolts for looseness.
• Check strut (shock absorber) for oil leakage or other damage.
• Check suspension ball joint for grease leakage and ball joint dust
cover for cracks or other damage.
SST851C
SMA525A
SFA392B
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст