Infiniti G37 Coupe. Manual — part 417
![](/vehicles/zatt/keash/ckiif/cirer.png)
TRUNK LID
DLK-229
< ON-VEHICLE REPAIR >
[INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
TRUNK LID WEATHERSTRIP : Exploded View
INFOID:0000000001722615
TRUNK LID WEATHERSTRIP : Removal and Installation
INFOID:0000000001722616
REMOVAL
Pull up and remove engagement with body from weather-strip joint.
CAUTION:
After removal, do not pull strongly on the weather-strip.
INSTALLATION
1.
Align the weather-strip seam (upper) with mark of the body panel and weather-strip onto the vehicle.
2.
Align the weather-strip seem (lower) with center of the striker and weather-strip onto the vehicle.
3.
After installation, pull the weather-strip gently to ensure that there is no loose section.
NOTE:
Check that the weather-strip fits tightly at each corner and trunk rear plate.
1.
Weather-strip
(A)
Seam (upper)
(B)
Seam (lower)
JMKIA0046ZZ
![](/vehicles/zatt/keash/ckiif/usomeeresl.png)
DLK-230
< ON-VEHICLE REPAIR >
[INTELLIGENT KEY SYSTEM]
DOOR LOCK
DOOR LOCK
DOOR LOCK
DOOR LOCK : Exploded View
INFOID:0000000001722617
DOOR LOCK : Removal and Installation
INFOID:0000000001722618
REMOVAL
1.
Remove the door finisher. Refer to
INT-11, "Removal and Installation"
.
2.
Remove the door glass and door module assembly.
• Door glass: Refer to
GW-16, "Removal and Installation"
• Door module: Refer to
GW-19, "Removal and Installation"
3.
Remove the door side grommet, and loosen the door key cylinder assembly (driver side) and outside han-
dle escutcheon (passenger side) TORX bolt from grommet hole.
CAUTION:
1.
Rear gasket
2.
TORX bolt
3.
Key cylinder rod (Driver side only)
4.
Door lock assembly
5.
Inside handle cap
6.
Inside handle
7.
Inside handle bracket
8.
Outside handle
9.
Door key cylinder assembly (Driver
side)
Outside handle escutcheon (Pas-
senger side)
10. Outside handle bracket
11.
Front gasket
Refer to
for symbols in the figure.
JMKIA1220GB
![](/vehicles/zatt/keash/ckiif/zchond.png)
DOOR LOCK
DLK-231
< ON-VEHICLE REPAIR >
[INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
Do not forcibly remove the TORX bolt.
4.
Disconnect the door antenna and door request switch connector and remove the harness clamp.
5.
Reach in to separate the key cylinder rod connection (on the handle).
6.
While pulling the outside handle, remove the door key cylinder
assembly.
7.
Slide toward rear of vehicle, and pull forward to remove the out-
side handle.
8.
Remove the front gasket and rear gasket.
9.
Remove the TORX bolts, and remove the door lock assembly.
JMKIA0020ZZ
PIIB5809E
JMKIA0967ZZ
PIIB5811E
![](/vehicles/zatt/keash/ckiif/ilamom.png)
DLK-232
< ON-VEHICLE REPAIR >
[INTELLIGENT KEY SYSTEM]
DOOR LOCK
10. Remove the TORX bolt of the outside handle bracket.
11. While pulling the outside handle bracket, slide toward rear of
vehicle to remove the outside handle bracket.
12. Disconnect the door lock actuator connector and remove the door lock assembly.
13. Reach in to separate the outside handle cable connection.
INSTALLATION
Install in the reverse order of removal.
CAUTION:
To install each rod, rotate the rod holder until a click is felt.
INSIDE HANDLE
JMKIA0022ZZ
PIIB5814E
PIIB5815E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст