Infiniti Q45 (FY33). Manual — part 230
SEF353Q
SEC049C
SEF763P
SEF593U
COMPONENT INSPECTION
EVAP canister purge volume control valve
1. Disconnect EVAP canister purge volume control valve
harness connector.
2. Check resistance between the following terminals.
terminal
q
2
and terminals
q
1
,
q
3
terminal
q
5
and terminals
q
4
,
q
6
Resistance:
Approximately 35 - 43
Ω
[At 25°C (77°F)]
3. Reconnect EVAP canister purge volume control valve
harness connector.
4. Remove EVAP canister purge volume control valve
from intake manifold collector and disconnect hoses
from the valve.
(Plug the purge hoses. The EVAP canister purge vol-
ume control valve harness connector should remain
connected.)
5. Turn ignition switch “ON”.
6. Perform “PURG VOL CONT/V” in “ACTIVE TEST”
mode with CONSULT-II. Check that EVAP canister
purge volume control valve shaft moves smoothly for-
ward and backward according to the valve opening.
If NG, replace the EVAP canister purge volume control
valve.
------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------ OR ------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
1. Disconnect EVAP canister purge volume control valve
harness connector.
2. Check resistance between the following terminals.
terminal
q
2
and terminals
q
1
,
q
3
terminal
q
5
and terminals
q
4
,
q
6
Resistance:
Approximately 35 - 43
Ω
[At 25°C (77°F)]
3. Reconnect EVAP canister purge volume control valve
harness connector.
4. Remove EVAP canister purge volume control valve
from intake manifold collector and disconnect hoses
from the valve.
(Plug the purge hoses. The EVAP canister purge vol-
ume control valve harness connector should remain
connected.)
5. Turn ignition switch “ON” and “OFF”. Check that EVAP
canister purge volume control valve shaft moves
smoothly forward and backward according to the igni-
tion switch position.
If NG, replace the EVAP canister purge volume control
valve.
GI
MA
EM
LC
FE
AT
PD
FA
RA
BR
ST
RS
BT
HA
EL
IDX
TROUBLE DIAGNOSIS FOR DTC P1444
Evaporative Emission (EVAP) Canister Purge
Volume Control Valve (Cont’d)
EC-449
SEF357W
SEF799W
COMPONENT INSPECTION
EVAP control system pressure sensor
1.
Remove EVAP control system pressure sensor with its har-
ness connector connected.
2.
Remove hose from EVAP control system pressure sensor.
3.
Turn ignition switch “ON”.
4.
Use pump to apply vacuum and pressure to EVAP control
system pressure sensor as shown in figure.
5.
Check output voltage between ECM terminal
q
92
and ground.
Pressure (Relative to atmospheric pressure)
Voltage (V)
0 kPa (0 mmHg, 0 inHg)
3.0 - 3.6
−9.3 kPa (−70 mmHg, −2.76 inHg)
0.4 - 0.6
CAUTION:
I
Always calibrate the vacuum pump gauge when using it.
I
Do not apply below −20 kPa (−150 mmHg, −5.91 inHg) or
over 20 kPa (150 mmHg, 5.91 inHg) of pressure.
6.
If NG, replace EVAP control system pressure sensor.
I
Never apply force to the air hole protector of the sensor,
if equipped.
I
Discard any EVAP control system pressure sensor which
has been dropped from a height of more than 0.5 m (19.7
in) onto a hard surface such as a concrete floor; use a new
one.
SEC050C
AEC783A
EVAP canister vent control valve
Check air passage continuity.
Perform “VENT CONTROL/V” in “ACTIVE TEST” mode with
CONSULT-II.
Condition
VENT CONTROL/V
Air passage continuity
between
q
A
and
q
B
ON
No
OFF
Yes
------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------ OR ------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
Condition
Air passage continuity
between
q
A
and
q
B
12V direct current supply between ter-
minals
q
1
and
q
2
No
No supply
Yes
If NG or operation takes more than 1 second, clean valve using air
blower or replace as necessary.
TROUBLE DIAGNOSIS FOR DTC P1444
Evaporative Emission (EVAP) Canister Purge
Volume Control Valve (Cont’d)
EC-450
If the portion
q
B
is rusted, replace EVAP canister vent control
valve.
Make sure new O-ring is installed properly.
GI
MA
EM
LC
FE
AT
PD
FA
RA
BR
ST
RS
BT
HA
EL
IDX
TROUBLE DIAGNOSIS FOR DTC P1444
Evaporative Emission (EVAP) Canister Purge
Volume Control Valve (Cont’d)
EC-451
SEF419U
Evaporative Emission (EVAP) Canister Vent
Control Valve (Close)
COMPONENT DESCRIPTION
The EVAP canister vent control valve is located on the EVAP can-
ister and is used to seal the canister vent.
This solenoid (the EVAP canister vent control valve) responds to
signals from the ECM.
When the ECM sends an ON signal, the coil in the solenoid valve
is energized.
A plunger will then move to seal the canister vent. The ability to seal
the vent is necessary for the on board diagnosis of other evapora-
tive emission control system components.
This solenoid valve is used only for diagnosis, and usually remains
opened.
When the vent is closed, under normal purge conditions, the
evaporative emission control system is depressurized and allows
“EVAP Control System (Small Leak)” diagnosis.
CONSULT-II REFERENCE VALUE IN DATA MONITOR MODE
Specification data are reference values.
MONITOR ITEM
CONDITION
SPECIFICATION
VENT CONT/V
I
Ignition switch: ON
OFF
ECM TERMINALS AND REFERENCE VALUE
Specification data are reference values and are measured between each terminal and ground.
CAUTION:
Do not use ECM ground terminals when measuring voltage. Doing so may result in damage to the
ECM’s transistor. Use a ground other than ECM terminals such as the body ground.
TER-
MINAL
NO.
WIRE
COLOR
ITEM
CONDITION
DATA
(DC Voltage)
20
P/B
EVAP canister vent con-
trol valve
Ignition switch “ON”
BATTERY VOLTAGE
(11 - 14V)
ON BOARD DIAGNOSIS LOGIC
Diagnostic
Trouble Code
No.
Malfunction is detected when .
Check Items
(Possible Cause)
P1446
0215
I
EVAP canister vent control valve remains closed
under specified driving conditions.
I
EVAP canister vent control valve
I
EVAP control system pressure sensor and the circuit
I
Blocked rubber tube to EVAP canister vent control
valve
I
Water separator
I
EVAP canister is saturated with water.
TROUBLE DIAGNOSIS FOR DTC P1446
EC-452
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст