Infiniti M35/M45 Y50. Manual — part 603
![](/vehicles/zatt/cen/houeebante/ato.png)
DTC P0031, P0032, P0051, P0052 A/F SENSOR 1 HEATER
EC-885
[VK45DE]
C
D
E
F
G
H
I
J
K
L
M
A
EC
Specification data are reference values and are measured between each terminal and ground.
Pulse signal is measured by CONSULT-II.
CAUTION:
Do not use ECM ground terminals when measuring input/output voltage. Doing so may result in dam-
age to the ECM's transistor. Use a ground other than ECM terminals, such as the ground.
: Average voltage for pulse signal (Actual pulse signal can be confirmed by oscilloscope.)
TER-
MINAL
NO.
WIRE
COLOR
ITEM
CONDITION
DATA (DC Voltage)
2
SB
A/F sensor 1 heater
(bank 1)
[Engine is running]
●
Warm-up condition
●
Idle speed
Approximately 5V
16
W/L
A/F sensor 1 (bank 1)
[Engine is running]
●
Warm-up condition
●
Idle speed
Approximately 3.1V
35
GR/L
Approximately 2.6V
56
LG/B
Approximately 2.3V
75
Y
Approximately 2.3V
PBIB1584E
![](/vehicles/zatt/cen/houeebante/youig.png)
EC-886
[VK45DE]
DTC P0031, P0032, P0051, P0052 A/F SENSOR 1 HEATER
BANK 2
TBWT1034E
![](/vehicles/zatt/cen/houeebante/uru.png)
DTC P0031, P0032, P0051, P0052 A/F SENSOR 1 HEATER
EC-887
[VK45DE]
C
D
E
F
G
H
I
J
K
L
M
A
EC
Specification data are reference values and are measured between each terminal and ground.
Pulse signal is measured by CONSULT-II.
CAUTION:
Do not use ECM ground terminals when measuring input/output voltage. Doing so may result in dam-
age to the ECM's transistor. Use a ground other than ECM terminals, such as the ground.
: Average voltage for pulse signal (Actual pulse signal can be confirmed by oscilloscope.)
Diagnostic Procedure
NBS005BM
1.
CHECK GROUND CONNECTIONS
1.
Turn ignition switch OFF.
2.
Loosen and retighten ground screws on the body.
Refer to
OK or NG
OK
>> GO TO 2.
NG
>> Repair or replace ground connections.
TER-
MINAL
NO.
WIRE
COLOR
ITEM
CONDITION
DATA (DC Voltage)
24
SB
A/F sensor 1 heater
(bank 2)
[Engine is running]
●
Warm-up condition
●
Idle speed
Approximately 5V
57
BR/W
A/F sensor 1 (bank 2)
[Engine is running]
●
Warm-up condition
●
Idle speed
Approximately 2.6V
58
G/O
Approximately 2.3V
76
G/W
Approximately 3.1V
77
GR
Approximately 2.3V
PBIB1584E
1.
Body ground M70
2.
Body ground M16
PBIB2782E
![](/vehicles/zatt/cen/houeebante/ortey.png)
EC-888
[VK45DE]
DTC P0031, P0032, P0051, P0052 A/F SENSOR 1 HEATER
2.
CHECK AIR FUEL RATIO (A/F) SENSOR 1 POWER SUPPLY CIRCUIT
1.
Disconnect air fuel ratio (A/F) sensor 1 harness connector.
2.
Turn ignition switch ON.
3.
Check voltage between A/F sensor 1 terminal 3 and ground with
CONSULT-II or tester.
OK or NG
OK
>> GO TO 4.
NG
>> GO TO 3.
3.
DETECT MALFUNCTIONING PART
Check the following.
●
Harness connectors E12, F3
●
IPDM E/R harness connector E7
●
15A fuse
●
Harness for open or short between A/F sensor 1 and fuse
>> Repair or replace harness or connectors.
4.
CHECK A/F SENSOR 1 HEATER OUTPUT SIGNAL CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect ECM harness connector.
3.
Check harness continuity between the following;
ECM terminal 2 and A/F sensor 1 (bank 1) terminal 4 or
ECM terminal 24 and A/F sensor 1 (bank 2) terminal 4.
Refer to Wiring Diagram.
4.
Also check harness for short to ground and short to power.
OK or NG
OK
>> GO TO 5.
NG
>> Repair open circuit or short to ground or short to power in harness or connectors.
: Vehicle front
1.
A/F sensor 1 (bank 2)
harness connector
2.
A/F sensor 1 (bank 1)
harness connector
Voltage: Battery voltage
PBIB2715E
PBIB1683E
Continuity should exist.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст