Infiniti M35/M45 Y50. Manual — part 1155
FRONT WIPER AND WASHER SYSTEM
WW-25
C
D
E
F
G
H
I
J
L
M
A
B
WW
CONSULT-II Functions (BCM)
NKS003WL
CONSULT-II can display each diagnostic item using the diagnostic test mode shown following.
CONSULT-II BASIC OPERATION
Refer to
GI-38, "CONSULT-II Start Procedure"
.
WORK SUPPORT
Operation Procedure
1.
Touch “WIPER” on “SELECT TEST ITEM” screen.
2.
Touch “WORK SUPPORT” on “SELECT DIAG MODE” screen.
3.
Touch “WIPER SPEED SETTING” on “SELECT WORK ITEM” screen.
4.
Touch “START”.
5.
Touch “CHANGE SETT”.
6.
The setting will be changed and“ CURRENT SETTING” will be displayed.
7.
Touch “END”.
Work Support Setting Item
NOTE:
Factory setting
DATA MONITOR
Operation Procedure
1.
Touch “WIPER” on “SELECT TEST ITEM” screen.
2.
Touch “DATA MONITOR” on “SELECT DIAG MODE” screen.
3.
Touch either “ALL SIGNALS” or “SELECTION FROM MENU” on “SELECT MONITOR ITEM” screen.
4.
When “SELECTION FROM MENU” is selected, touch items to be monitored. If “ALL SIGNALS” is
selected, all items will be monitored.
5.
Touch “START”.
6.
Touch “RECORD” while monitoring to record the status of the item being monitored. To stop recording,
touch “STOP”.
BCM diagnosis position
Diagnosis mode
Description
WIPER
WORK SUPPORT
Changes the setting for each function.
DATA MONITOR
Displays BCM input data in real time.
ACTIVE TEST
Device operation can be checked by applying a drive signal to device.
BCM
SELF-DIAG RESULTS
BCM performs self-diagnosis of CAN communication.
CAN DIAG SUPPORT MNTR
The result of transmit/receive diagnosis of CAN communication can be read.
Item
Description
CONSULT-II
WIPER SPEED SETTING
When wiper switch is at INTERMITTENT, front wiper intermittent time can be selected
according to vehicle speed.
●
ON (Operated)/OFF
NOTE
(Not operated)
ON/OFF
ALL SIGNALS
Monitors all the signals.
SELECTION FROM MENU
Selects items and monitors them.
WW-26
FRONT WIPER AND WASHER SYSTEM
Display Item List
ACTIVE TEST
Operation Procedure
1.
Touch “WIPER” on “SELECT TEST ITEM” screen.
2.
Touch “ACTIVE TEST” on “SELECT DIAG MODE” screen.
3.
Touch “FR WIPER” on “SELECT TEST ITEM” screen.
4.
Touch items to be tested, and check operation.
5.
During operation check, touching “OFF” deactivates operation.
Display Item List
NOTE:
With INTERMITTENT operation, the front wiper moves only once.
Monitor item
Contents
IGN ON SW
“ON/OFF”
Displays status (ignition switch IGN position: ON/other: OFF) of ignition switch judged from the
ignition switch signal.
IGN SW CAN
“ON/OFF”
Displays status (ignition switch IGN position: ON/other: OFF) of ignition switch judged from the
ignition switch signal (CAN communication lines).
FR WIPER HI
“ON/OFF”
Displays status (front wiper switch high position: ON/other: OFF) of front wiper high switch
judged from the wiper switch signal.
FR WIPER LOW
“ON/OFF”
Displays status (front wiper switch low position: ON/other: OFF) of front wiper low switch
judged from the wiper switch signal.
FR WIPER INT
“ON/OFF”
Displays status (front wiper switch intermittent position: ON/other: OFF) of front wiper intermit-
tent switch judged from the wiper switch signal.
FR WASHER SW
“ON/OFF”
Displays status (front washer switch ON position: ON/other: OFF) of front washer switch judged
from the wiper switch signal.
INT VOLUME
“1 - 7”
Displays status (wiper intermittent dial position setting 1- 7) of intermittent volume switch
judged from the wiper switch signal.
FR WIPER STOP
“ON/OFF”
Displays status (front wiper stop position: ON/move: OFF) of front wiper motor stop judged
from the front wiper auto stop signal.
VEHICLE SPEED
“km/h”
Displays status vehicle speed as judged from vehicle speed signal.
Test item
Indication on CONSULT-II display
Description
Front wiper output
FR WIPER
With a certain operation (HI, LO, INT), the front wiper can be oper-
ated.
NOTE
FRONT WIPER AND WASHER SYSTEM
WW-27
C
D
E
F
G
H
I
J
L
M
A
B
WW
CONSULT-II Functions (IPDM E/R)
NKS003WM
CONSULT-II can display each diagnostic item using the diagnostic test mode shown following.
CONSULT-II BASIC OPERATION
Refer to
GI-38, "CONSULT-II Start Procedure"
.
DATA MONITOR
Operation Procedure
1.
Touch “DATA MONITOR” on “SELECT DIAG MODE ” screen.
2.
Touch “ALL SIGNALS”, “MAIN SIGNALS” or “SELECTION FROM MENU” on the “SELECT MONITOR
ITEM” screen.
3.
When “SELECTION FROM MENU” is selected, touch individual items to be monitored. In “ALL SIG-
NALS”, all items are monitored. In “MAIN SIGNALS”, predetermined items are monitored.
4.
Touch “START”.
5.
Touch “RECORD” while monitoring to record the status of the item being monitored. To stop recording,
touch “STOP”.
All Signals, Main Signals, Selection From Menu
NOTE:
Perform monitoring of IPDM E/R data with the ignition switch ON. When the ignition switch is at ACC, the dis-
play may not be correct.
ACTIVE TEST
Operation Procedure
1.
Touch “ACTIVE TEST” on “SELECT DIAG MODE” screen.
2.
Touch “FRONT WIPER” on “SELECT TEST ITEM” screen.
3.
Touch item to be tested, and check operation.
4.
Touch “OFF” while testing to stop the operation.
Diagnosis Mode
Description
SELF
−
DIAG RESULTS
Refer to
DATA MONITOR
The input/output data of IPDM E/R is displayed in real time.
CAN DIAG SUPPORT MNTR
The result of transmit/receive diagnosis of CAN communication can be read.
ACTIVE TEST
IPDM E/R sends a drive signal to electronic components to check their operation.
ALL SIGNALS
Monitors all items.
MAIN SIGNALS
Monitor the predetermined item.
SELECTION FROM MENU
Selects items and monitors them.
Item name
CONSULT-II
screen display
Display or unit
Monitor item selection
Description
ALL
SIGNALS
MAIN
SIGNALS
SELECTION
FROM MENU
FR wiper request
FR WIP REQ
STOP/1 LOW/
LOW/HI
×
×
×
Signal status input from BCM
Wiper auto stop
WIP AUTO STOP
ACT P/STOP P
×
×
×
Output status of IPDM E/R
Wiper protection
WIP PROT
OFF/BLOCK
×
×
×
Control status of IPDM E/R
Test item
CONSULT-II
screen display
Description
Front wiper (HI, LO) output
FRONT WIPER
With a certain operation (HI, LO), the front wiper relay (HIGH and LOW) can be
operated.
WW-28
FRONT WIPER AND WASHER SYSTEM
Front Wiper Does Not Operate
NKS003WN
CAUTION:
●
During IPDM E/R fail-safe control, front wipers may not operate. Refer to
in “PG IPDM E/R” to make sure that it is not in fail-safe status.
1.
ACTIVE TEST
With CONSULT-II
1.
Select “IPDM E/R” by CONSULT-II, and select “ACTIVE TEST”
on “SELECT DIAG MODE” screen.
2.
Select “FRONT WIPER” on “SELECT TEST ITEM” screen.
3.
Touch “LO” or “HI” screen.
Without CONSULT-II
Start up auto active test. Refer to
Does front wiper operate normally?
YES
>> GO TO 2.
NO
>> GO TO 4.
2.
CHECK CIRCUIT BETWEEN COMBINATION SWITCH AND BCM
With CONSULT-II
1.
Select “BCM” on CONSULT-II, and select “WIPER” on “SELECT
TEST ITEM” screen.
2.
Select “DATA MONITOR” on “SELECT DIAG MODE” screen.
Make sure that “FR WIPER INT”, “FR WIPER LOW”, and “FR
WIPER HI” turn ON-OFF according to wiper switch operation.
Without CONSULT-II
Refer to
LT-239, "Combination Switch Inspection"
OK or NG
OK
>> GO TO 3.
NG
>> Check combination switch (wiper switch). Refer to
239, "Combination Switch Inspection"
.
3.
CHECK CIRCUIT BETWEEN IPDM E/R AND BCM
Select “BCM” on CONSULT-II, and perform self-diagnosis for
“BCM”.
Displayed self-diagnosis results
BCS-15, "Removal and Installa-
CAN COMM CIRCUIT>>Check CAN communication line of BCM.
BCS-13, "CAN Communication Inspection
Using CONSULT-II (Self-Diagnosis)"
SKIA3486E
PKIB0110E
PKIA7627E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст