Infiniti M35/M45 Y50. Manual — part 1014
SUNROOF
RF-11
C
D
E
F
G
H
J
K
L
M
A
B
RF
System Description
NIS0023R
Power supplied at all time
●
through 50A fusible link (letter F , located in the fuse and fusible link box)
●
to BCM terminal 55.
●
through 10A fuse [No.21, located in the fuse block (J/B)]
●
to BCM terminal 42.
●
through BCM terminal 54
●
to sunroof motor assembly terminal 1.
When ignition switch ON or START position,
Power is supplied
●
through 15A fuse [No.1, located in the fuse block (J/B)]
●
to BCM terminal 38.
●
through BCM terminal 53
●
to sunroof motor assembly terminal 6.
Ground is supplied
●
to BCM terminal 52
●
through body grounds M16 and M70.
●
to sunroof motor assembly terminal 8
●
through body ground M16 and M70.
TILT UP / SLIDE CLOSE OPERATION
When tilt up / slide close switch is pressed,
Ground is supplied
●
to sunroof motor assembly terminal 11
●
through sunroof switch terminal 3
●
through sunroof switch terminal 2
●
through sunroof motor assembly terminal 9.
Then, the sunroof tilt up / slide close.
TILT DOWN / SLIDE OPEN OPERATION
When tilt down / slide open switch is pressed,
Ground is supplied
●
to sunroof motor assembly terminal 4
●
through sunroof switch terminal 1
●
through sunroof switch terminal 2
●
through sunroof motor assembly terminal 9.
Then, the sunroof tilt down / slide open.
AUTO OPERATION
The power sunroof AUTO feature makes it possible to slide open and slide close or tilt up and tilt down the
sunroof without holding the sunroof switch in the SLIDE OPEN/TILT DOWN or SLIDE CLOSE/TILT UP posi-
tion.
RETAINED POWER OPERATION
When the ignition switch is turned to OFF position from ON position, power is supplied for 45 seconds.
●
through BCM terminal 53.
●
to sunroof motor assembly terminal 6.
When power is supplied, the sunroof can be operated.
The retained power operation is canceled when the driver or passenger side door is opened.
RAP signal period can be changed by CONSULT-II. Refer to
RF-16, "CONSULT-II Function (BCM)"
.
RF-12
SUNROOF
ANTI-PINCH FUNCTION
The CPU of sunroof motor assembly monitors the sunroof motor operation and the sunroof position (fully-
closed or other) by the signals from sunroof motor.
When sunroof motor detects an interruption during the following slide close and tilt down operation, sunroof
motor assembly controls the motor until full up position (when tilt down operate) or 125 mm (4.92 in) or more to
open direction (when slide close operate).
The function is operated in the following conditions.
●
close operation and tilt down when ignition switch is in the ON position.
●
close operation and tilt down during retained power operation.
INITIALIZATION PROCEDURE
If the battery is disconnected, the sunroof motor connector is disconnected sunroof does not close or open
automatically, use the following procedure to return sunroof operation to normal.
1.
Close the sunroof if it is not in the closed position. It may be necessary to repeatedly push the switch to
close the sunroof.
2.
Press the SLIDE OPEN/TILT DOWN switch for approximately 1 second or more.
3.
Initialization procedure is completed. Confirm proper operation of the sunroof (slide open, slide close, tilt
up, tilt down.)
SUNROOF
RF-13
C
D
E
F
G
H
J
K
L
M
A
B
RF
Wiring Diagram — SROOF —
NIS0023S
TIWT1334E
RF-14
SUNROOF
TIWT2119E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст