Mitsubishi Lancer Evolution IX. Manual — part 389

TROUBLESHOOTING

MULTIPORT FUEL INJECTION (MPI)

13A-31

STEP 17. Perform voltage measurement at B-105
air flow sensor connector.

• Use special tool test harness (MB991709) to con-

nect connector, and measure at pick-up harness.

• Transmission: Neutral

• Voltage between terminal No. 7 and earth.

OK:

0

− 1 V (Engine: Idling)

6

− 9 V (Engine: 3,000 r/min.)

Q: Is the check result normal?

YES :

Go to Step 20 .

NO :

Go to Step 18 .

STEP 18. Connector check: C-121 engine-ECU
connector

Q: Is the check result normal?

YES :

Go to Step 19 .

NO :

Repair or replace the connector.

AK305005

3

4

5

1

2

6

7

AB

Connector : B-105

Harness side
connector

B-105(B)

AK501995

2

3

4

5

6

7

8

9

11

12

13

14

15

16

17

18

19

20

30

21

22

23

24

25

26

27

28

29

31

32

33

34

35

1

10

AB

Connector: C-121

C-121 (GR)

C-121 (GR)

Harness side connector

<L. H. drive vehicles>

<R. H. drive vehicles>

TROUBLESHOOTING

MULTIPORT FUEL INJECTION (MPI)

13A-32

STEP 19. Check harness between B-105 (terminal
No. 7) air flow sensor connector and C-121
(terminal No. 19) engine-ECU connector.

• Check reset signal line for open circuit and dam-

age.

Q: Is the check result normal?

YES :

Go to Step 8 .

NO :

Repair the damaged harness wire.

STEP 20. Perform output wave pattern
measurement at B-105 air flow sensor connector
(Using an oscilloscope).

• Use special tool test harness (MB991709) to con-

nect connector, and measure at pick-up harness.

• Engine: Idling

• Transmission: Neutral

• Voltage between terminal No. 3 and earth.

OK: Waveforms should be displayed on
inspection procedure using an oscilloscope
(Refer to

P.13A-385

) and noise should not be

displayed in the waveform.

Q: Is the check result normal?

YES :

Go to Step 8 .

NO :

Go to Step 21 .

STEP 21. Replace the air flow sensor.

• After replacing the air flow sensor, re-check the

trouble symptoms.

Q: Is the check result normal?

YES :

Go to Step 22 .

NO :

The check is end.

STEP 22. Connector check: B-12X engine control
relay connector

Q: Is the check result normal?

YES :

Go to Step 23 .

NO :

Repair or replace the connector.

AK305005

3

4

5

1

2

6

7

AB

Connector : B-105

Harness side
connector

B-105(B)

AK501995

2

3

4

5

6

7

8

9

11

12

13

14

15

16

17

18

19

20

30

21

22

23

24

25

26

27

28

29

31

32

33

34

35

1

10

AB

Connector: C-121

C-121 (GR)

C-121 (GR)

Harness side connector

<L. H. drive vehicles>

<R. H. drive vehicles>

AK305005

3

4

5

1

2

6

7

AB

Connector : B-105

Harness side
connector

B-105(B)

AK305003

2

1

3

4

AB

Connector : B-12X

B-12X

Harness side
connector

Relay box’s
triangle marks

TROUBLESHOOTING

MULTIPORT FUEL INJECTION (MPI)

13A-33

STEP 23. Check harness between B-105 (terminal
No. 4) air flow sensor connector and B-12X
(terminal No. 4) engine control relay connector.

• Check power supply line for damage.

Q: Is the check result normal?

YES :

Go to Step 24 .

NO :

Repair the damaged harness wire.

STEP 24. Connector check: C-119 engine-ECU
connector

Q: Is the check result normal?

YES :

Go to Step 25 .

NO :

Repair or replace the connector.

AK305005

3

4

5

1

2

6

7

AB

Connector : B-105

Harness side
connector

B-105(B)

AK305003

2

1

3

4

AB

Connector : B-12X

B-12X

Harness side
connector

Relay box’s
triangle marks

AK501994

65

43
50

42
49

41
48
60

61

64

46

47

58

59

67

68

45

56
66

52 51

44

53

62

54

63

57

55

AB

Connector: C-119

C-119 (GR)

C-119 (GR)

Harness side connector

<L. H. drive vehicles>

<R. H. drive vehicles>

TROUBLESHOOTING

MULTIPORT FUEL INJECTION (MPI)

13A-34

STEP 25. Check harness between B-105 (terminal
No. 3) air flow sensor connector and C-119
(terminal No. 61) engine-ECU connector.

• Check output line for damage.

Q: Is the check result normal?

YES :

Go to Step 26 .

NO :

Repair the damaged harness wire.

STEP 26. Connector check: C-121 engine-ECU
connector

Q: Is the check result normal?

YES :

Check and repair harness between B-105

(terminal No. 5) air flow sensor connector
and C-121 (terminal No. 34) engine-ECU
connector.

• Check earthing line for damage.

No :

Repair or replace the connector.

AK305005

3

4

5

1

2

6

7

AB

Connector : B-105

Harness side
connector

B-105(B)

AK501994

65

43
50

42
49

41
48
60

61

64

46

47

58

59

67

68

45

56
66

52 51

44

53

62

54

63

57

55

AB

Connector: C-119

C-119 (GR)

C-119 (GR)

Harness side connector

<L. H. drive vehicles>

<R. H. drive vehicles>

AK501995

2

3

4

5

6

7

8

9

11

12

13

14

15

16

17

18

19

20

30

21

22

23

24

25

26

27

28

29

31

32

33

34

35

1

10

AB

Connector: C-121

C-121 (GR)

C-121 (GR)

Harness side connector

<L. H. drive vehicles>

<R. H. drive vehicles>

AK305005

3

4

5

1

2

6

7

AB

Connector : B-105

Harness side
connector

B-105(B)