Mitsubishi Eclipse / Eclipse Spyder (2000-2002). Service and repair manual — part 466
![](/vehicles/winoney/isene/butrele/rayidallla.png)
AUTOMATIC TRANSAXLE DIAGNOSIS
TSB Revision
AUTOMATIC TRANSAXLE
23A-156
STEP 33. Check the Park/Neutral position switch.
Check for continuity between terminals for each selector
position.
NOTE: For vehicles with sport mode, four positions (P, R, N, D)
are used.
Q: Is the switch operating properly?
YES : Go to Step 34.
NO : Replace the Park/Neutral position switch. Refer to
GROUP 23B, Transaxle
.
STEP 34. Check connector B-41 at the Park/Neutral
position switch for damage.
Q: Is the connector in good condition?
YES : Go to Step 35.
NO : Repair or replace it. Refer to GROUP 00E, Harness
Connector Inspection
.
ITEMS
TERMINAL
CONNECTION OF
TESTER
SPECIFIED
CONDITION
P
3
−
8, 9
−
10
Less than 2 ohm.
R
7
−
8
N
4
−
8, 9
−
10
D
1
−
8
3
5
−
8
2
2
−
8
L
6
−
8
AC004672
DIPSTICK
PARK/NEUTRAL
POSITION (PNP)
SWITCH
AC
AC001846
P
R
N
D
3
2
L
AB
AC001844
CONNECTOR: B-41
DIPSTICK
AB
![](/vehicles/winoney/isene/butrele/ndiene.png)
AUTOMATIC TRANSAXLE DIAGNOSIS
TSB Revision
AUTOMATIC TRANSAXLE
23A-157
STEP 35. Check the switch output voltage at PCM
connector C-61 <2.4L Engine> or C-63 <3.0L Engine> by
backprobing.
(1) Do not disconnect connector C-61 <2.4L Engine> or C-63
<3.0L Engine>.
(2) Turn the ignition switch to "ON" position.
(3) Move the selector lever to "3" position.
(4) Measure the voltage between terminal 109 and ground by
backprobing.
•
Voltage should be battery positive voltage.
(5) Turn the ignition switch to "LOCK" (OFF) position.
Q: Is the voltage normal?
YES : Go to Step 12.
NO : Go to Step 36.
STEP 36. Check connectors C-61 <2.4L Engine> or C-63
<3.0L Engine> at PCM for damage.
Q: Is the connectors in good condition?
YES : Repair it because of the harness open circuit or short
circuit to ground between the Park/Neutral position
switch connector B-41 terminal 5 and PCM connector
C-61 <2.4L Engine> or C-63 <3.0L Engine> terminal
109.
NO : Repair or replace it. Refer to GROUP 00E, Harness
Connector Inspection
.
AC001657
CONNECTOR: C-61 <2.4L ENGINE> OR
C-63 <3.0L ENGINE>
PCM
AN
AC001907
C-61 <2.4L ENGINE> OR
C-63 <3.0L ENGINE>
CONNECTOR HARNESS
SIDE VIEW
AD
AC001657
CONNECTOR: C-61 <2.4L ENGINE> OR
C-63 <3.0L ENGINE>
PCM
AN
![](/vehicles/winoney/isene/butrele/itrorumanori.png)
AUTOMATIC TRANSAXLE DIAGNOSIS
TSB Revision
AUTOMATIC TRANSAXLE
23A-158
STEP 37. Check the Park/Neutral position switch.
Check for continuity between terminals for each selector
position.
NOTE: For vehicles with sport mode, four positions (P, R, N, D)
are used.
Q: Is the switch operating properly?
YES : Go to Step 38.
NO : Replace the Park/Neutral position switch. Refer to
GROUP 23B, Transaxle
.
STEP 38. Check connector B-41 at the Park/Neutral
position switch for damage.
Q: Is the connector in good condition?
YES : Go to Step 39.
NO : Repair or replace it. Refer to GROUP 00E, Harness
Connector Inspection
.
ITEMS
TERMINAL
CONNECTION OF
TESTER
SPECIFIED
CONDITION
P
3
−
8, 9
−
10
Less than 2 ohm.
R
7
−
8
N
4
−
8, 9
−
10
D
1
−
8
3
5
−
8
2
2
−
8
L
6
−
8
AC004672
DIPSTICK
PARK/NEUTRAL
POSITION (PNP)
SWITCH
AC
AC001846
P
R
N
D
3
2
L
AB
AC001844
CONNECTOR: B-41
DIPSTICK
AB
![](/vehicles/winoney/isene/butrele/aksth.png)
AUTOMATIC TRANSAXLE DIAGNOSIS
TSB Revision
AUTOMATIC TRANSAXLE
23A-159
STEP 39. Check the switch output voltage at PCM
connector C-61 <2.4L Engine> or C-63 <3.0L Engine> by
backprobing.
(1) Do not disconnect connector C-61 <2.4L Engine> or C-63
<3.0L Engine>.
(2) Turn the ignition switch to "ON" position.
(3) Move the selector lever to "2" position.
(4) Measure the voltage between terminal 122 and ground by
backprobing.
•
Voltage should be battery positive voltage.
(5) Turn the ignition switch to "LOCK" (OFF) position.
Q: Is the voltage normal?
YES : Go to Step 12.
NO : Go to Step 40.
STEP 40. Check connectors C-61 <2.4L Engine> or C-63
<3.0L Engine> at PCM for damage.
Q: Is the connector in good condition?
YES : Repair it because of the harness open circuit or short
circuit to ground between the Park/Neutral position
switch connector B-41 terminal 2 and PCM connector
C-61 <2.4L Engine> or C-63 <3.0L Engine> terminal
122.
NO : Repair or replace it. Refer to GROUP 00E, Harness
Connector Inspection
.
AC001657
CONNECTOR: C-61 <2.4L ENGINE> OR
C-63 <3.0L ENGINE>
PCM
AN
AC001908
C-61 <2.4L ENGINE> OR
C-63 <3.0L ENGINE>
CONNECTOR HARNESS
SIDE VIEW
AD
AC001657
CONNECTOR: C-61 <2.4L ENGINE> OR
C-63 <3.0L ENGINE>
PCM
AN
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст