Mitsubishi Eclipse / Eclipse Spyder (2000-2002). Service and repair manual — part 126
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI) <2.4L ENGINE>
13A-203
STEP 1. Using scan tool MB991502, check actuator test
item 10: EGR solenoid.
CAUTION
To prevent damage to scan tool MB991502, always turn the
ignition switch to the "LOCK" (OFF) position before
connecting or disconnecting scan tool MB991502.
(1) Connect scan tool MB991502 to the data link connector.
(2) Turn the ignition switch to the "ON" position.
(3) Set scan tool MB991502 to the actuator test mode for item
10, EGR solenoid.
•
An operation sound should be heard and vibration
should be felt when the EGR solenoid is operated.
(4) Turn the ignition switch to the "LOCK" (OFF) position.
Q: Is the solenoid operating properly?
YES : It can be assumed that this malfunction is intermittent.
Refer to GROUP 00, How to Use Troubleshooting/
Inspection Service Points (
NO : Go to Step 2.
STEP 2. Check connector B-31 at the EGR solenoid for
damage.
Q: Is the connector in good condition?
YES : Go to Step 3.
NO : Repair or replace it. Refer to GROUP 00E, Harness
Connector Inspection (
AKX01177
16 PIN
MB991502
AB
ACX02513
EGR
SOLENOID
VALVE
CONNECTOR:B-31
AI
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI) <2.4L ENGINE>
13A-204
STEP 3 Check the EGR solenoid.
(1) Disconnect the EGR solenoid connector B-31.
(2) Measure the resistance between EGR solenoid side
connector terminal 1 and 2.
Standard value: 29
−
35
Ω
[at 20
°
C (68
°
F)]
Q: Is the resistance at the standard value?
YES : Go to Step 4.
NO : Replace the EGR solenoid. Then go to Step 12.
STEP 4. Check the power supply voltage at EGR solenoid
harness side connector B-31.
(1) Disconnect the connector B-31 and measure at the harness
side.
(2) Turn the ignition switch to the "ON" position.
(3) Measure the voltage between terminal 1 and ground.
•
Voltage should be battery positive voltage
(4) Turn the ignition switch to the "LOCK" (OFF) position.
Q: Is the voltage normal?
YES : Go to Step 6.
NO : Go to Step 5.
STEP 5. Check connector A-21X at MFI relay for damage.
Q: Is the connector in good condition?
YES : Check connector B-13 at intermediate connector for
damage, and repair or replace as required. Refer to
GROUP 00E, Harness Connector Inspection (
). If intermediate connectors is in good condition,
repair harness wire between MFI relay connector A-
21X terminal 1 and EGR solenoid connector B-31
terminal 1 because of open circuit or short circuit to
ground. Then go to Step 12.
NO : Repair or replace it. Refer to GROUP 00E, Harness
Connector Inspection (
ACX02513
EGR
SOLENOID
VALVE
CONNECTOR:B-31
AI
AKX00352
AK000254 AE
B-31 HARNESS
SIDE CONNECTOR
1
2
AK000226
AK000226AB
CONNECTOR : A-21X
MFI RELAY
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI) <2.4L ENGINE>
13A-205
STEP 6. Check the power supply voltage at ECM connector
C-49 <M/T> or PCM connector C-50 <A/T> by backprobing
(1) Do not disconnect the connector C-49 <M/T> or C-50 <A/
T>.
(2) Turn the ignition switch to the "ON" position.
(3) Measure the voltage between terminal 6 and ground by
backprobing.
•
Voltage should be battery positive voltage.
(4) Turn the ignition switch to the "LOCK" (OFF) position.
Q: Is the voltage normal?
YES : Go to Step 9.
NO : Go to Step 7.
STEP 7. Check connector C-49 at ECM <M/T> or connector
C-50 at PCM <A/T> for damage.
Q: Is the connector in good condition?
YES : Go to Step 8.
NO : Repair or replace it. Refer to GROUP 00E, Harness
Connector Inspection (
AK000298
10
1 2 3 4 5 6 7 8 9
1112 13
141516171819 20 2122 23242526
AC
<M/T>
C-49 CONNECTOR
HARNESS SIDE VIEW
AK000299
1
2
3 4
5 6
7 8
9 10 11 1213 141516 17 1819 20 21 2223
24 25
2627 2829
30 3132 33
3435
AD
C-50 CONNECTOR
HARNESS SIDE VIEW
<A/T>
AK000280
C-49,C-50
ECM<M/T>
OR
PCM<A/T>
CONNECTORS:C-49<M/T>,C-50<A/T>
BC
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI) <2.4L ENGINE>
13A-206
STEP 8. Check for open circuit and short circuit to ground
between EGR solenoid connector B-31 terminal 2 and ECM
connector C-49 terminal 6 <M/T> or PCM connector C-50
terminal 6 <A/T>.
NOTE: Check harness after checking intermediate connector
B-13.If intermediate connectors is damaged, repair or replace
them.Refer to GROUP 00E, Harness Connector Inspection
(
Q: Is the harness wire in good condition?
YES : Replace the ECM or PCM. Then go to Step 12.
NO : Repair it. Then go to Step 12.
STEP 9. Check connector C-49 at ECM <M/T> or connector
C-50 at PCM <A/T> for damage.
Q: Is the connector in good condition?
YES : Go to Step 10.
NO : Repair or replace it. Refer to GROUP 00E, Harness
Connector Inspection (
ACX02513
EGR
SOLENOID
VALVE
CONNECTOR:B-31
AI
AK000280
C-49,C-50
ECM<M/T>
OR
PCM<A/T>
CONNECTORS:C-49<M/T>,C-50<A/T>
BC
AK000280
C-49,C-50
ECM<M/T>
OR
PCM<A/T>
CONNECTORS:C-49<M/T>,C-50<A/T>
BC
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст