Mitsubishi Eclipse / Eclipse Spyder (2000-2002). Service and repair manual — part 586
![](/vehicles/winoney/isene/butrele/iceki.png)
ANTI-SKID BRAKING SYSTEM (ABS) DIAGNOSIS
TSB Revision
ANTI-LOCK BRAKING SYSTEM (ABS)
35B-35
STEP 5. Check the connectors A-02, C-42, and C-94.
Refer to GROUP 00E, Harness Connector Inspection
Q: Is any of the connectors damaged?
YES : Repair it and then go to Step 9.
NO : Go to Step 6.
AC001985
CONNECTOR: A-02
AD
AC004483AB
CONNECTOR: C-42
COMBINATION
METER
AC004410AB
CONNECTOR: C-94
![](/vehicles/winoney/isene/butrele/beron.png)
ANTI-SKID BRAKING SYSTEM (ABS) DIAGNOSIS
TSB Revision
ANTI-LOCK BRAKING SYSTEM (ABS)
35B-36
STEP 6. Check the continuity between the combination
meter and the ABS-ECU.
Check the continuity between the combination meter connector
C-42 (terminal 24) and the ABS-ECU connector A-02 (terminal
21).
NOTE: This check must be done with the ABS-ECU connector
A-02 is connected to the ABS-ECU. Disconnection of the ABS-
ECU connector A-02 makes the connector lock switch OFF, so
this continuity check could not be done.
Q: Is there the continuity between the combination meter
connector C-42 (terminal 24) and the ABS-ECU
connector A-02 (terminal 21)?
YES : Go to Step 9.
NO : Repair the harness wire and then go to Step 9.
STEP 7. Check the connectors C-41, C-101, and C-104.
Refer to GROUP 00E, Harness Connector Inspection
Q: Is any of the connectors damaged?
YES : Repair it and then go to Step 9.
NO : Go to Step 8.
AC001985
CONNECTOR: A-02
AD
AC004483AB
CONNECTOR: C-42
COMBINATION
METER
AC004482 AB
CONNECTOR: C-41
COMBINATION METER
AC004411AB
CONNECTORS: C-101, C-104
C-104
C-101
![](/vehicles/winoney/isene/butrele/netha.png)
ANTI-SKID BRAKING SYSTEM (ABS) DIAGNOSIS
TSB Revision
ANTI-LOCK BRAKING SYSTEM (ABS)
35B-37
STEP 8. Check the continuity between the ignition switch
(IG1) and the combination meter.
Q: Is there any continuity (less than 2 ohm) between the
ignition switch (IG1) and the combination meter
connector C-41 (terminal 52)?
YES : Go to Step 9.
NO : Repair the harness wire and then go to Step 9.
STEP 9. Check symptoms.
Q: Does the ABS warning light illuminate for 3 seconds
when the ignition switch is turned to the "ON" position
with engine stopped or upon start-up?
YES : This diagnosis is complete.
NO : Return to Step 1.
AC004482 AB
CONNECTOR: C-41
COMBINATION METER
![](/vehicles/winoney/isene/butrele/deardis.png)
ANTI-SKID BRAKING SYSTEM (ABS) DIAGNOSIS
TSB Revision
ANTI-LOCK BRAKING SYSTEM (ABS)
35B-38
INSPECTION PROCEDURE 3: The ABS Warning Light Remains Illuminated after the Engine is Started.
NOTE: This diagnosis procedure is limited to cases where communication with the scan tool is possible
(ABS-ECU power supply is normal) and no diagnostic trouble code outputs.
NOTE: CONNECTOR LOCK SWITCH
ON: The ABS-ECU connector A-02 is connected.
OFF: The ABS-ECU connector A-02 is disconnected.
ABS Warning Light Circuit
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст