Mitsubishi Eclipse / Eclipse Spyder (2000-2002). Service and repair manual — part 432
AUTOMATIC TRANSAXLE DIAGNOSIS
TSB Revision
AUTOMATIC TRANSAXLE
23A-19
Incomplete
shifting
1st
Gear ratio value which is
sent from the output shaft
speed sensor is not
identical to the output from
the input shaft speed
sensor for one second
after shifting finished.
The diagnostic trouble code is displayed and the
judgement condition occurs once. When the
judgement condition is met four times, the A/T
control relay is turned off and for vehicles with sport
mode "N" range light flashes.
2nd
3rd
4th
Reverse
A/T control relay
A/T control relay voltage is
less than seven volts for
0.1 second after the
ignition switch is turned
"ON."
Switch the A/T control relay off and for vehicles with
sport mode "N" range light flashes.
Abnormality in the PCM
Abnormality has occurred
in the PCM.
Switch the A/T control relay off.
MALFUNCTIONING
ITEM
JUDGEMENT
CONDITION
CONTROL CONTENTS DURING MALFUNCTION
AUTOMATIC TRANSAXLE DIAGNOSIS
TSB Revision
AUTOMATIC TRANSAXLE
23A-20
ROAD TEST
M1231007800065
Check by the following procedures
STEP
CONDITION BEFORE
TEST/OPERATION
TEST/OPERATION
STANDARD
INSPECTION
ITEM
DTC
INSPECTION
PROCEDURE
PAGE
1
Ignition switch:
(LOCK) OFF
Ignition switch
(1) ON
Data list No. 54
(1) Control
Relay Voltage
[V]
A/T Control
relay
output
voltage
54
A/T Control
relay system
(
.)
2
Ignition switch:
ON
Engine: Stopped
Selector lever
position: P
Selector lever position
<Vehicles without sport
mode>
(1) P, (2) R, (3) N, (4) D, (5)
3, (6) 2, (7) L
Data list No. 61
(1) P, (2) R, (3)
N, (4) D, (5) 3,
(6) 2, (7) L
Park/
Neutral
position
switch
27,
28
Park/Neutral
position switch
system
(
,
Selector lever position
<Vehicles with sport
mode>
(1) P, (2) R, (3) N, (4) D
Data list No. 61
(1) P, (2) R, (3)
N, (4) D
Selector lever position
<Vehicles with sport
mode>
(1) D (1st gear)
(2) Select the sport mode
(1st gear)
(3) Upshift and hold the
selector lever in that
position (2nd gear)
(4) Downshift and hold the
selector lever in that
position (1st gear)
Data list No. 67
(1) OFF, (2) ON,
(3) ON, (4) ON
Data list No. 68
(1) OFF, (2) OFF,
(3) ON, (4) OFF
Data list No. 69
(1) OFF, (2) OFF,
(3) OFF, (4) ON
Select
switch
Shift switch
-
Shift switch
assembly
system (
Shift indicator
light
(1) "D" or "1"
illuminates
(2) Only "1"
illuminates
(3) Only "2"
illuminates
(4) Only "1"
illuminates
Accelerator pedal
(1)Fully closed
(2)Depressed
(3)Fully open
Data list No. 11
(1)535
−
735 mV
(2)Gradually
rises from (1)
(3)4,500
−
5,500
mV
TPS
11,
12,
14
TPS system
(
,
Brake pedal
(1)Depressed
(2)Released
Data list No. 26
(1)ON
(2)OFF
Stoplight
switch
26
Stoplight
switch system
(
.)
3
Ignition switch:
ST
Engine: Stopped
Starting test with lever in P
or N range
Starting should
be possible
Starting
-
Vehicles does
not move
(
.)
AUTOMATIC TRANSAXLE DIAGNOSIS
TSB Revision
AUTOMATIC TRANSAXLE
23A-21
4
Warming up
Drive for 15 minutes or
more so that the A/T fluid
temperature becomes 70
−
80
°
C. (158
−
176
°
F)
Data list No. 15
Gradually rises
to 70
−
80
°
C
(158
−
176
°
F)
A/T fluid
temperatur
e sensor
15,
16
A/T fluid
temperature
sensor system
(
,
5
Engine: Idling
Selector lever
position: N
Brake pedal (Retest)
(1)Depressed
(2)Released
Data list No. 26
(1)ON
(2)OFF
Stoplight
switch
26
Stoplight
switch system
(
.)
A/C switch
(1)ON
(2)OFF
Data list No. 65
(1)ON
(2)OFF
Dual
pressure
switch
-
Vehicle shifts
differently with
A/C engaged
(
.)
5
Engine: Idling
Selector lever
position: N
Accelerator pedal
(1)Fully closed
(2)Depressed
Data list No. 21
(1)Engine
tachometer and
the MUT-II
shows the same
engine speed
(2)Gradually
rises from (1)
Crankshaft
position
sensor
21
Crankshaft
position sensor
system (
STEP
CONDITION BEFORE
TEST/OPERATION
TEST/OPERATION
STANDARD
INSPECTION
ITEM
DTC
INSPECTION
PROCEDURE
PAGE
AUTOMATIC TRANSAXLE DIAGNOSIS
TSB Revision
AUTOMATIC TRANSAXLE
23A-22
5
Engine: Idling
Selector lever
position: N
Selector lever position
(1)N
→
D
(2)N
→
R
Should be no
abnormal shift
shocks
Time delay when
engaging should
be within 2
seconds
Malfunction
when
starting
-
Engine stalls
when moving
selector lever
from N to D or
N to R (
-
Shift shocks
when shifting
from N to D
and long delay
(
.)
-
Shift shocks
when shifting
from N to R
and long delay
(
.)
-
Shift shocks
when shifting
from N to D, N
to R and long
delay (
Does not
move
-
Does not move
forward
(
.)
-
Does not move
backward
(
.)
-
Does not move
(forward or
backward)
(
.)
STEP
CONDITION BEFORE
TEST/OPERATION
TEST/OPERATION
STANDARD
INSPECTION
ITEM
DTC
INSPECTION
PROCEDURE
PAGE
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст