Mitsubishi Eclipse / Eclipse Spyder (2000-2002). Service and repair manual — part 379
AUTO-CRUISE CONTROL
TSB Revision
ENGINE AND EMISSION CONTROL
17-35
CIRCUIT OPERATION
The throttle position sensor signal is sent to the auto-
cruise control-ECU through this circuit.
The auto-cruise control-ECU receives a signal from
the throttle position sensor at terminal 3.
The signal is OFF when the accelerator pedal is
depressed, and ON when the accelerator pedal is
released.
The throttle position sensor sends a voltage signal to
terminal 1 of the auto-cruise control-ECU.
The voltage depends on throttle opening angle.
DTC SET CONDITIONS
If 2.5 volts or more 0.2 volts or less is output for four
seconds or more.
TROUBLESHOOTING HINTS
The most likely causes for this code to be set are:
•
Malfunction of the throttle position sensor.
•
Damaged harness or connector.
•
Malfunction of the auto-cruise control-ECU.
DIAGNOSIS
Required Special Tools:
•
MB991502: Scan Tool (MUT-II)
•
MB991223: Harness Set
STEP 1. Check the throttle position sensor.
CAUTION
To prevent damage to scan tool MB991502, always turn the
ignition switch to "LOCK" (OFF) position before
connecting or disconnecting scan tool MB991502.
(1) Using scan tool MB991502.
(2) Connect scan tool MB991502 to the data link connector.
(3) Turn the ignition switch to "ON" position.
(4) Read the MFI-DTC.
(5) Turn the ignition switch to "LOCK" (OFF) position.
Q: Is the MFI-DTC P0120 is output?
YES : For 2.4L Engine, refer to GROUP 13A, Diagnosis
−
.
For 3.0L Engine, refer to GROUP 13B, Diagnosis
−
.
NO : Go to Step 2.
AC001451
CONNECTOR: C-20
AB
AC003599 AB
CONNECTOR: C-28
AC001252
MB991502
16 PIN
AB
AUTO-CRUISE CONTROL
TSB Revision
ENGINE AND EMISSION CONTROL
17-36
STEP 2. Check the output circuit voltage at auto-cruise
control-ECU connector C-20 by backprobing.
(1) Do not disconnect auto-cruise control-ECU connector C-20.
(2) Turn the ignition switch to "ON" position and the auto-cruise
control main switch to "ON" position.
(3) Measure the voltage between terminal 1 and ground by
backprobing.
•
Voltage should be between 4.0 and 5.5 volts.
(When accelerator pedal is fully depressed.)]
•
Voltage should be between 0.4 and 1.0 volts.
(When accelerator pedal is released.)
(4) Turn the ignition switch to "LOCK" (OFF) position.
Q: Are the voltage within specifications?
YES : Check that diagnostic trouble code 17 is not output.
If diagnostic trouble code 17 is output, replace the
auto-cruise control-ECU. (Refer to
.)
Then check that diagnostic trouble code 17 is not.
NO : Go to Step 3.
STEP 3. Check auto-cruise control-ECU connector C-20.
Q: Is the connector damaged?
YES : Repair or replace connector.
Refer to GROUP 00E, Harness Connector Inspection
.
Then check that diagnostic trouble code 17 is not
output.
NO : Go to Step 4.
1 2 3 4 5 6 7 8
9 10 11 12 13 14 15 16
ACX01901
C-20 CONNECTOR
HARNESS SIDE VIEW
AE
AC001451
CONNECTOR: C-20
AB
AUTO-CRUISE CONTROL
TSB Revision
ENGINE AND EMISSION CONTROL
17-37
STEP 4. Check the harness wire between throttle position
sensor connector B-07 and auto-cruise control-ECU
connector C-20.
Q: Is the harness wire between throttle position sensor
connector B-07 and auto-cruise control-ECU connector
C-20 damaged?
YES : Repair harness wire and then check that diagnostic
trouble code 17 is not output.
NO : Check that diagnostic trouble code 17 is not output.
If diagnostic trouble code 17 is output, replace the
auto-cruise control-ECU. (Refer to
.)
Then check that diagnostic trouble code 17 is not
output.
AC005105
CONNECTOR: B-07 <2.4L ENGINE>
AB
AC005106
CONNECTOR: B-07 <3.0L ENGINE>
AB
AC001451
CONNECTOR: C-20
AB
AUTO-CRUISE CONTROL
TSB Revision
ENGINE AND EMISSION CONTROL
17-38
SYMPTOM CHART
M1172002300098
SYMPTOMS
INSPECTION
PROCEDURE
NO.
REFERENCE
PAGE
Communication with scan tool
MB991502 is not possible
Communication with all systems is
not possible
-
<2.4 L>
<3.0 L>
Communication with auto-cruise
control-ECU only is not possible
1
Auto-cruise control is not
cancelled.
When brake pedal is depressed
2
When clutch pedal is depressed <M/
T>
3
When selector lever is moved to "N"
range <A/T>
4
When "CANCEL" switch is turned
ON
5
Auto-cruise control cannot be set.
6
Hunting (repeated acceleration and deceleration) occurs at the set
vehicle speed.
7
Auto-cruise control indicator light inside combination meter does not
illuminate. (However, auto-cruise control is normal.)
8
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст