Mitsubishi Eclipse / Eclipse Spyder (2000-2002). Service and repair manual — part 525
TRANSAXLE
TSB Revision
AUTOMATIC TRANSAXLE OVERHAUL
23B-31
3. Install the low-reverse brake piston, return spring, and
spring retainer into the transaxle case.
4. Fit a new O-ring into the groove of one-way clutch inner
race.
5. Check the placement of the identification notches in the one-
way clutch inner race. Install the one-way clutch inner race
to the transfer drive gear bearing so that the notches fall
along the A
−
A line.
6. Put the snap ring on the inner race.
7. Set special tools MD998703 <F4A42> or MD998338
<F4A51> and MD998924 as shown, and then compress the
one-way clutch inner race and install the snap ring.
NOTE: This illustration shows F4A51.
8. Install the wave spring onto the low-reverse brake piston.
AKX01116
IDENTIFICATION
NOTCHES
TRANSAXLE
CASE
A
A
AB
AKX01107AB
MD998924
MD998903
<F4A42> OR
MD998338
<F4A51>
AKX01023
TRANSAXLE
TSB Revision
AUTOMATIC TRANSAXLE OVERHAUL
23B-32
CAUTION
If necessary, take the measurements in steps 9 to 18 after
replacing the pressure plate, brake plate and brake disc.
9. Install the six brake discs, five brake plates and snap ring as
shown in the figure.
NOTE: Do not install the pressure plate at this time.
10.Install special tool MB991631 <F4A42> or MB991632
<F4A51> on the brake disc.
11.Install the reaction plate and the used snap ring.
12.Move special tool MB991631 <F4A42> or MB991632
<F4A51> to measure the end play of reaction plate. Then
replace the snap ring installed in step 11 to adjust the end
play to standard value.
Standard value: 0
−
0.16 mm (0
−
0.0063 inch)
13.Install the brake discs and brake plates as shown in the
figure.
Number of brake discs and plates
14.Place special tool MB991631 <F4A42> or MB991632
<F4A51> on top of the brake disc in place of the pressure
plate.
15.Install the return spring, second brake piston and snap ring.
A/T MODEL
BRAKE DISC
BRAKE PLATE
F4A42
3
2
F4A51
4
3
AKX01119
<F4A42>
SNAP RING
REACTION PLATE
MB991631
AB
AKX01120
<F4A51>
REACTION PLATE
SNAP RING
MB991632
AB
AKX1137
<F4A42>
SECOND BRAKE
PISTON
SNAP RING
MB991631
RETURN
SPRING
AB
AKX01121
<F4A51> SECOND BRAKE
PISTON
MB991632
SNAP RING
RETURN
SPRING
AB
TRANSAXLE
TSB Revision
AUTOMATIC TRANSAXLE OVERHAUL
23B-33
16.Move special tool MB991631 <F4A42> or MB991632
<F4A51> and measure its movement.
Standard value of end play (Reference):
0.79
−
1.25 mm (0.0311
−
0.0492 inch) <F4A42>
1.09
−
1.55 mm (0.0429
−
0.0610 inch) <F4A51>
17.Select a pressure plate whose thickness corresponds to the
measured amount of movement from the following table.
PRESSURE PLATE FOR F4A42
PRESSURE PLATE FOR F4A51
18.Turn the transaxle over so that the installation surface of the
torque converter housing is facing up.
Install special tool MD998913 in a dial gauge, and then
move special tool MB991631 <F4A42> or MB991632
<F4A51> and measure its movement.
Standard value of end play (Reference):
1.65
−
2.11 mm (0.050
−
0.0831 inch)
MOVEMENT AMOUNT
mm (in)
THICKNESS
mm (in)
ID
SYMBOL
PRESSURE
PLATE
PART NO.
0.6
−
0.8 (0.024
−
0.031) 1.6 (0.063)
L
MD759567
0.8
−
1.0 (0.031
−
0.039) 1.8 (0.071)
1
MD759414
1.0
−
1.2 (0.039
−
0.047) 2.0 (0.079)
0
MD759415
1.2
−
1.4 (0.047
−
0.055) 2.2 (0.087)
2
MD759416
1.4
−
1.6 (0.055
−
0.063) 2.4 (0.094)
4
MD759417
1.6
−
1.8 (0.063
−
0.071) 2.6 (0.102)
6
MD759418
MOVEMENT AMOUNT
mm (in)
THICKNESS
mm (in)
ID
SYMBOL
PRESSURE
PLATE
PART NO.
1.1
−
1.3 (0.043
−
0.051) 1.8 (0.071)
E
MD759425
1.3
−
1.5 (0.051
−
0.059) 2.0 (0.079)
D
MD759426
1.5
−
1.7 (0.059
−
0.067) 2.2 (0.087)
C
MD759427
1.7
−
1.9 (0.067
−
0.075) 2.4 (0.094)
B
MD759428
1.9
−
2.1 (0.075
−
0.083) 2.6 (0.102)
A
MD759429
2.1
−
2.3 (0.083
−
0.091) 2.8 (0.110)
0
MD759430
AKX01068
MB991631 <F4A42> OR
MB991632 <F4A51>
AB
AKX01138
<F4A42>
MOVEMENT
AMOUNT
AB
AKX01122
<F4A51>
MOVEMENT
AMOUNT
AB
AKX01069AB
MD998913
MB991631
<F4A42> OR
MB991632
<F4A51>
TRANSAXLE
TSB Revision
AUTOMATIC TRANSAXLE OVERHAUL
23B-34
19.Select a pressure plate whose thickness corresponds to the
measured amount of movement from the table below.
NOTE: This illustration shows F4A51.
PRESSURE PLATE FOR F4A42
PRESSURE PLATE FOR F4A51
20.Remove all parts and special tools that were installed to
take the measurements in steps 8 to 18. Remove and
separate the pressure plate and snap ring chosen in steps
12, 16 and 18.
21.Install the snap ring into the groove of transaxle case output
shaft bore.
22.Install the thinnest output shaft preload adjustment spacer
[thickness 1.88 mm (0.0740 in); part number MD756579].
23.Use special tools MB990930 and MB990938 to tap the
output shaft bearing outer race in the transaxle case.
MOVEMENT AMOUNT
mm (in)
THICKNESS
mm (in)
ID
SYMBOL
PRESSURE
PLATE PART
NO.
1.3
−
1.5 (0.051
−
0.059) 1.6 (0.063)
L
MD759567
1.5
−
1.7 (0.059
−
0.067) 1.8 (0.071)
1
MD759414
1.7
−
1.9 (0.067
−
0.075) 2.0 (0.079)
0
MD759415
1.9
−
2.1 (0.075
−
0.083) 2.2 (0.087)
2
MD759416
2.1
−
2.3 (0.083
−
0.091) 2.4 (0.094)
4
MD759417
2.3
−
2.5 (0.091
−
0.098) 2.6 (0.102)
6
MD759418
2.5
−
2.7 (0.098
−
0.106) 2.8 (0.110)
8
MD759419
2.7
−
2.9 (0.106
−
0.114) 3.0 (0.118)
D
MD759420
MOVEMENT AMOUNT
mm (in)
THICKNESS
mm (in)
ID
SYMBOL
PRESSURE
PLATE PART
NO.
1.0
−
1.2 (0.039
−
0.047) 1.6 (0.063)
F
MD759568
1.2
−
1.4 (0.047
−
0.055) 1.8 (0.071)
E
MD759425
1.4
−
1.6 (0.055
−
0.063) 2.0 (0.079)
D
MD759426
1.6
−
1.8 (0.063
−
0.071) 2.2 (0.087)
C
MD759427
1.8
−
2.0 (0.071
−
0.079) 2.4 (0.094)
B
MD759428
2.0
−
2.2 (0.079
−
0.087) 2.6 (0.102)
A
MD759429
2.2
−
2.4 (0.087
−
0.094) 2.8 (0.110)
0
MD759430
2.4
−
2.6 (0.094
−
0.102) 3.0 (0.118)
1
MD759431
AKX01123
<F4A42>
MD998913
MB991631
AB
MOVEMENT
AMOUNT
AKX01124
<F4A51>
MD998913
MB991632
AB
MOVEMENT
AMOUNT
AKX01060
MB990938
MB990930
AB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст