Mitsubishi Eclipse / Eclipse Spyder (2000-2002). Service and repair manual — part 444
![](/vehicles/winoney/isene/butrele/zallind.png)
AUTOMATIC TRANSAXLE DIAGNOSIS
TSB Revision
AUTOMATIC TRANSAXLE
23A-67
STEP 7. Check connectors B-07 at throttle position sensor
and C-57 <2.4L Engine> or C-59 <3.0L Engine> at PCM for
damage.
Q: Are the connectors in good condition?
YES : Repair it because of harness open circuit or damage
between throttle position sensor connector B-07
terminal 3 and PCM connector C-57 <2.4L Engine> or
C-59 <3.0L Engine> terminal 78.
NO : Repair or replace it. Refer to GROUP 00E, Harness
Connector Inspection
.
STEP 8. Check the power supply voltage at throttle
position sensor connector B-07 by backprobing.
(1) Do not disconnect connector B-07.
(2) Turn the ignition switch to "ON" position.
(3) Measure the voltage between terminal 4 and ground by
backprobing.
•
Voltage should be between 4.8 and 5.2 volts.
(4) Turn the ignition switch to "LOCK" (OFF) position.
Q: Is the voltage normal?
YES : Go to Step 13.
NO : Go to Step 9.
AC001831AB
CONNECTOR: B-07
<2.4L ENGINE>
<3.0L ENGINE>
AC001657
CONNECTOR: C-57 <2.4L ENGINE> OR
C-59 <3.0L ENGINE>
AK
PCM
AC001831AB
CONNECTOR: B-07
<2.4L ENGINE>
<3.0L ENGINE>
AC001789
B-07 CONNECTOR
HARNESS SIDE VIEW
AC
![](/vehicles/winoney/isene/butrele/upan.png)
AUTOMATIC TRANSAXLE DIAGNOSIS
TSB Revision
AUTOMATIC TRANSAXLE
23A-68
STEP 9. Check the power supply voltage at PCM connector
C-54 <2.4L Engine> or C-55 <3.0L Engine> by backprobing.
(1) Do not disconnect connector C-54 <2.4L Engine> or C-55
<3.0L Engine>.
(2) Turn the ignition switch to "ON" position.
(3) Measure the voltage between terminal 46 and ground by
backprobing.
•
Voltage should be between 4.8 and 5.2 volts.
(4) Turn the ignition switch to "LOCK" (OFF) position.
Q: Is the voltage normal?
YES : Go to Step 10.
NO : Go to Step 11.
STEP 10. Check connectors B-07 at throttle position
sensor and C-54 <2.4L Engine> or C-55 <3.0L Engine> at
PCM for damage.
Q: Are the connectors in good condition?
YES : Repair it because of harness open circuit or damage
between throttle position sensor connector B-07
terminal 4 and PCM connector C-54 <2.4L Engine> or
C-55 <3.0L Engine> terminal 46.
NO : Repair or replace it. Refer to GROUP 00E, Harness
Connector Inspection
.
AC001657
CONNECTOR: C-54 <2.4L ENGINE> OR
C-55 <3.0L ENGINE>
PCM
AL
AC000848
C-54 <2.4L ENGINE> OR
C-55 <3.0L ENGINE>
CONNECTOR HARNESS
SIDE VIEW
AD
AC001831AB
CONNECTOR: B-07
<2.4L ENGINE>
<3.0L ENGINE>
AC001657
CONNECTOR: C-54 <2.4L ENGINE> OR
C-55 <3.0L ENGINE>
PCM
AL
![](/vehicles/winoney/isene/butrele/mellong.png)
AUTOMATIC TRANSAXLE DIAGNOSIS
TSB Revision
AUTOMATIC TRANSAXLE
23A-69
STEP 11. Check connectors B-07 at throttle position
sensor and C-54 <2.4L Engine> or C-55 <3.0L Engine> at
PCM for damage.
Q: Are the connectors in good condition?
YES : Go to Step 12.
NO : Repair or replace it. Refer to GROUP 00E, Harness
Connector Inspection
.
STEP 12. Check harness for short circuit to ground
between throttle position sensor connector B-07 terminal 4
and PCM connector C-54 <2.4L Engine> or C-55 <3.0L
Engine> terminal 46.
Q: Is the harness wire in good condition?
YES : Go to Step 6.
NO : Repair it.
AC001831AB
CONNECTOR: B-07
<2.4L ENGINE>
<3.0L ENGINE>
AC001657
CONNECTOR: C-54 <2.4L ENGINE> OR
C-55 <3.0L ENGINE>
PCM
AL
AC001831AB
CONNECTOR: B-07
<2.4L ENGINE>
<3.0L ENGINE>
AC001657
CONNECTOR: C-54 <2.4L ENGINE> OR
C-55 <3.0L ENGINE>
PCM
AL
![](/vehicles/winoney/isene/butrele/gous.png)
AUTOMATIC TRANSAXLE DIAGNOSIS
TSB Revision
AUTOMATIC TRANSAXLE
23A-70
STEP 13. Check the ground voltage at throttle position
sensor connector B-07 by backprobing.
(1) Do not disconnect connector B-07.
(2) Turn the ignition switch to "ON" position.
(3) Measure the voltage between terminal 1 and ground by
backprobing.
•
Voltage should be 0.5 volt or less.
(4) Turn the ignition switch to "LOCK" (OFF) position.
Q: Is the voltage normal?
YES : Go to Step 17.
NO : Go to Step 14.
STEP 14. Check the ground voltage at PCM connector C-54
<2.4L Engine> or C-55 <3.0L Engine> by backprobing.
(1) Do not disconnect connector C-54 <2.4L Engine> or C-55
<3.0L Engine>.
(2) Turn the ignition switch to "ON" position.
(3) Measure the voltage between terminal 57 and ground by
backprobing.
•
Voltage should be 0.5 volt or less.
(4) Turn the ignition switch to "LOCK" (OFF) position.
Q: Is the voltage normal?
YES : Go to Step 15.
NO : Go to Step 16.
AC001831AB
CONNECTOR: B-07
<2.4L ENGINE>
<3.0L ENGINE>
AC001790
B-07 CONNECTOR
HARNESS SIDE VIEW
AC
AC001657
CONNECTOR: C-54 <2.4L ENGINE> OR
C-55 <3.0L ENGINE>
PCM
AL
AC001791
C-54 <2.4L ENGINE> OR
C-55 <3.0L ENGINE>
CONNECTOR HARNESS
SIDE VIEW
AD
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст