Mitsubishi Eclipse / Eclipse Spyder (2000-2002). Service and repair manual — part 216
![](/vehicles/winoney/isene/butrele/eraroe.png)
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI) <3.0L ENGINE>
13B-63
STEP 14. Check for open circuit and harness damage
between intake air temperature sensor connector B-14
terminal 5 and ECM connector C-58 terminal 49 <M/T> or
PCM connector C-55 terminal 57 <A/T>.
Q: Is the harness wire in good condition?
YES : Replace the ECM or PCM. Then go to Step 19.
NO : Repair it. Then go to Step 19.
ACX02480
CONNECTOR : B-14
AG
INTAKE AIR
TEMPERATURE
SENSOR
AK000225
CONNECTOR : C-58<M/T>, C-55<A/T>
C-55
C-58
PCM<A/T>
ECM<M/T>
AI
![](/vehicles/winoney/isene/butrele/lee.png)
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI) <3.0L ENGINE>
13B-64
STEP 15. Check the intake air temperature sensor.
(1) Disconnect the intake air temperature sensor connector B-
14
(2) Measure the resistance between intake air temperature
sensor side connector terminal 5 and 6.
(3) Measure resistance while heating the sensor using a hair
drier.
Standard value:
5.3
−
6.7 k
Ω
[at 0
°
C (32
°
F)]
2.3
−
3.0 k
Ω
[at 20
°
C (68
°
F)]
1.0
−
1.5 k
Ω
[at 40
°
C (104
°
F)]
0.30
−
0.42 k
Ω
[at 80
°
C (176
°
F)]
Q: Is the resistance at the standard value?
YES : Go to Step 16.
NO : Replace the volume air flow sensor. Then go to Step
19.
STEP 16. Check connector C-58 at ECM <M/T> or
connector C-55 at PCM <A/T> for damage.
Q: Is the connector in good condition?
YES : Go to Step 17.
NO : Repair or replace it. Refer to GROUP 00E, Harness
Connector Inspection (
). Then go to Step 19.
ACX02480
CONNECTOR : B-14
AG
INTAKE AIR
TEMPERATURE
SENSOR
AKX01407AB
INTAKE AIR TEMPERATURE
SENSOR SIDE CONNECTOR
1 2 3 4 5 6 7
AKX01621 AB
INTAKE AIR
TEMPERATURE
SENSOR
AK000225
CONNECTOR : C-58<M/T>, C-55<A/T>
C-55
C-58
PCM<A/T>
ECM<M/T>
AI
![](/vehicles/winoney/isene/butrele/hochavere.png)
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI) <3.0L ENGINE>
13B-65
STEP 17. Check for harness damage between intake air
temperature sensor connector B-14 terminal 5 and ECM
connector C-58 terminal 49 <M/T> or PCM connector C-55
terminal 57 <A/T>.
Q: Is the harness wire in good condition?
YES : Go to Step 18.
NO : Repair it. Then go to Step 19.
STEP 18. Check for harness damage between intake air
temperature sensor connector B-14 terminal 6 and ECM
connector C-58 terminal 62 <M/T> or PCM connector C-55
terminal 64 <A/T>.
Q: Is the harness wire in good condition?
YES : Replace the ECM or PCM. Then go to Step 19.
NO : Repair it. Then go to Step 19.
ACX02480
CONNECTOR : B-14
AG
INTAKE AIR
TEMPERATURE
SENSOR
AK000225
CONNECTOR : C-58<M/T>, C-55<A/T>
C-55
C-58
PCM<A/T>
ECM<M/T>
AI
ACX02480
CONNECTOR : B-14
AG
INTAKE AIR
TEMPERATURE
SENSOR
AK000225
CONNECTOR : C-58<M/T>, C-55<A/T>
C-55
C-58
PCM<A/T>
ECM<M/T>
AI
![](/vehicles/winoney/isene/butrele/yan.png)
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI) <3.0L ENGINE>
13B-66
STEP 19. Test the OBD-II drive cycle.
(1) Carry out a test drive with the drive cycle pattern. Refer to
, Procedure 6
−
Other Monitor.
(2) Check the diagnostic trouble code (DTC).
Q: Is the DTC P0111 is output?
YES : Retry the troubleshooting.
NO : The inspection is complete.
DTC P0115: Engine Coolant Temperature Circuit High Input
AK000688
1 2
BLA
CK
YELLO
W
-GREEN
49<M/T>
57<A/T>
44
ENGINE CONTROL
MODULE(ECM)<M/T>
OR
POWERTRAIN CONTROL
MODULE(PCM)<A/T>
ENGINE COOLANT
TEMPERATURE SENSOR
B-11
(MU802406)
2
1
5V
65
43
50
42
49
41
48
60 61
64
46 47
58 59
67 68
45
56
66
52
51
44
53
62
54
63
57
55
C-58<M/T>
(MU803782)
C-55<A/T>
(MU803781)
42 43
48 49 50 51 52 53 54 55 56 57
46
45
44
58 59
60 61 62 63
64 65 66
47
41
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст