Mitsubishi Eclipse / Eclipse Spyder (2000-2002). Service and repair manual — part 403
CLUTCH RELEASE CYLINDER
TSB Revision
CLUTCH OVERHAUL
21B-9
<3.0L ENGINE>
AKX00762
7
8
11 ± 2 N·m
8 ± 1 ft-lb
3
2
9
1
6
4
5
AB
DISASSEMBLY STEPS
1. PUSH ROD
2. BOOT
<<A>>
>>A<<
3 PISTON ASSEMBLY
4. PISTON CUP
5. PISTON
6. CONICAL SPRING
7. CAP
8. AIR BLEEDER
9. RELEASE CYLINDER
DISASSEMBLY STEPS (Continued)
CLUTCH RELEASE CYLINDER
TSB Revision
CLUTCH OVERHAUL
21B-10
DISASSEMBLY SERVICE POINT
<<A>> PISTON ASSEMBLY REMOVAL
1. Cover with a shop towel to prevent the piston from popping
out.
CAUTION
Apply compressed air slowly to prevent brake fluid from
splashing.
2. Apply the compressed air into the tube mounting hole to
remove the piston assembly.
ASSEMBLY SERVICE POINT
>>A<< PISTON ASSEMBLY INSTALLATION
1. Apply brake fluid SAE J1703 (DOT3) to the piston cup and
inner surface of the release cylinder.
2. Insert the piston assembly into the release cylinder.
INSPECTION
M1212001600042
PISTON CUP
Check the lip of piston cup for scratch. If it is scratched, check
the inner surface of the release cylinder for scratches.
RELEASE CYLINDER
Check the inner surface of the release cylinder for scratches or
abnormal wear, replace if necessary.
AKX00765
AKX00763
AKX00754
SPECIFICATIONS
TSB Revision
CLUTCH OVERHAUL
21B-11
SPECIFIC ATIO NS
FASTENER TIGHTENING SPECIFICATIONS
M1212001800046
GENERAL SPECIFICATIONS
M1212000200041
SERVICE SPECIFICATIONS
M1212000300048
LUBRICANTS
M1212000400056
ITEMS
SPECIFICATIONS
Clutch cover mounting bolt
19
±
3 N
⋅
m (14
±
2 ft-lb)
Clutch fluid line bracket bolt
19
±
3 N
⋅
m (14
±
2 ft-lb)
Clutch release cylinder air bleeder <2.4L engine>
17
±
2 N
⋅
m (12
±
1 ft-lb)
Clutch release cylinder air bleeder <3.0L engine>
11
±
2 N
⋅
m (8
±
1 ft-lb)
Clutch release cylinder mounting bolt
19
±
3 N
⋅
m (14
±
2 ft-lb)
Clutch release cylinder union bolt
23
±
2 N
⋅
m (17
±
1 ft-lb)
Clutch tube flare nut
15
±
2 N
⋅
m (11
±
1 ft-lb)
Fulcrum <2.4L engine>
35
±
6 N
⋅
m (26
±
4 ft-lb)
Release fork shaft locking bolt <3.0L engine>
9.8
±
2 N
⋅
m (87
±
17 in-lb)
ITEMS
SPECIFICATIONS
Clutch operating method
Hydraulic type
Clutch disc type
Single dry disc type
Clutch disc size OD x ID mm (in) <2.4L engine>
215 x 140 (8.46 x 5.51)
Clutch disc size OD x ID mm (in) <3.0L engine>
225 x 150 (8.87 x 5.91)
Clutch cover type
Diaphragm spring type
Clutch cover setting load N (lb) <2.4L engine>
4,539 (1,014)
Clutch cover setting load N (lb) <3.0L engine>
5,864 (1,318)
Clutch release cylinder ID mm (in) <2.4L engine>
19.05 (3/4)
Clutch release cylinder ID mm (in) <3.0L engine>
20.64 (13/16)
ITEMS
LIMIT
Clutch disc facing rivet sink mm (in)
Minimum 0.3 (0.012)
Diaphragm spring end height difference mm (in)
0.5 (0.020)
ITEMS
SPECIFIED LUBRICANTS
Release fork and fulcrum contact surface <2.4L engine>
MITSUBISHI genuine grease Part Number
0101011 or equivalent
Release fork and release cylinder pushrod contact surface
Release fork and release bearing contact surface
Release fork bushing inner surface <3.0L engine>
Piston and piston cup
Brake fluid SAE J1703 (DOT3)
Release cylinder inner surface
NOTES
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст