Acura RL (1996-2004 year). Manual — part 340
Cylinder Heads
Installation (cont'd)
12. Install the intake manifold and water passage, then
tighten the intake manifold mounting bolts and nuts
in a crisscross pattern in 2 or 3 steps, beginning
with the inner bolts.
NOTE: Always use new intake manifold gaskets.
13. Install the EGR pipe.
6 x 1.0 mm
12 N-m (1.2 kgf-m,
8.7 Ibf-ft)
8 x 1.25 mm
22 N-m (2.2 kgf-m, 16 Ibf-ft)
GASKETS
Replace.
6 x 1.0 mm
12 N-m (1.2 kgf-m,
8.7 Ibf-ft)
WATER
PASSAGE
EGR PIPE
GASKETS
Replace.
O-RING
Replace.
14. Install the exhaust manifolds. Tighten the nuts in a
crisscross pattern in 2 or 3 steps, beginning with the
inner nut (see page
).
NOTE: Always use new exhaust manifold gaskets.
15. After installation, check that all tubes, hoses and
connectors are installed correctly.
16. Enter the anti-theft code for the radio, then enter the
customer's radio station presets.
Main Menu
Table of Contents
07GAD - PH70201
07LAB - PV00100
07749 - 0010000
07948 - SB00101
07965 - SD90200
Special Tools
Main Menu
Table of Contents
Illustrated Index
Lubricate all internal parts with engine oil during reassembly.
NOTE: Use liquid gasket, Part No. 08718 - 0001 or 08718 - 0003.
BALANCER
SHAFT
O-RING
Replace.
DOWEL
PIN
BALANCER GEAR
CASE
Apply liquid gasket to
the block mating
surface.
BALANCER SHAFT
HOLDER
Apply liquid gasket around
the oil hole to the block
mating surface.
O-RING
Replace.
6 x 1.0 mm
12 N-m (1.2 kgf-m,
8.7 Ibf-ft)
BALANCER SHAFT
REAR COVER
6 x 1.0 mm
12 N-m (1.2 kgf-m,
8.7 Ibf-ft)
8 x 1.25 mm
25 N-m (2.5 kgf-m,
18 Ibf-ft)
REAR BALANCER
WEIGHT
O-RING
Replace.
OUTER PIPE
O-RING
Replace.
ENGINE OIL PRESSURE
SWITCH
18 N-m (1.8 kgf-m, 13 Ibf-ft)
1/8 in. BSPT (British
Standard Pipe Taper)
28 threads/inch. Use
proper liquid sealant.
6 x 1.0 mm
12 N-m (1.2 kgf-m,
8.7 Ibf-ft)
O-RING
Replace.
Main Menu
Table of Contents
Illustrated Index
(cont'd)
Lubricate all internal parts with engine oil during reassembly.
NOTE:
• Apply liquid gasket to the mating surfaces of the rear
cover and oil pump case before installing them.
• Use liquid gasket. Part No. 08718 - 0001 or 08718 - 0003.
OIL PAN INNER
PIPE
Clean when installing.
OIL FILTER
OIL PAN
Apply liquid gasket
to mating surface.
8 x 1.25 mm
22 N-m (2.2 kgf-m,
16 Ibf-ft)
SNAP RING
Install with open
side facing up.
6 x 1.0 mm
12 N-m (1.2 kgf-m, 8.7 Ibf-ft)
TORQUE CONVERTER
COVER
12 x 1.0 mm
74 N-m (7.5 kgf-m,
54 Ibf-ft)
WASHER
DRIVE PLATE
Check for cracks.
CRANKSHAFT OIL
SEAL
Replace.
6 x 1.0 mm
12 N-m (1.2 kgf-m,
8.7 Ibf-ft)
REAR COVER
Apply liquid gasket to
block mating surface.
O-RING
Replace.
DOWEL
PIN
6 x 1.0 mm
12 N-m (1.2 kgf-m,
8.7 Ibf-ft)
CRANKSHAFT OIL
SEAL
and
Replace.
8 x 1.25 mm
22 N-m (2.2 kgf-m,
16 Ibf-ft)
Apply liquid gasket
to block mating surface.
O-RINGS
Replace.
DOWEL
PIN
O-RING
Replace.
O-RINGS
Replace.
Main Menu
Table of Contents
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст