Acura RLX Hybrid (2017 year). Manual — part 10
151
uu
Security System
u
Security System Alarm
Co
ntrols
■
The panic button on the remote
transmitter
If you press the panic button for
approximately one second, the following will
occur for about 30 seconds:
• The horn sounds.
• Some exterior lights flash.
■
Canceling panic mode
Press any button on the remote transmitter, or set the power mode to ON.
■
Panic Mode
Panic
Button
Panic
Button
17 ACURA RLX E-AWD-31TY36300.book 151 ページ 2016年6月17日 金曜日 午前8時29分
-------------------------------------------------------------------------------------------------------------------------------------------------------------
152
Co
ntrols
Opening and Closing the Windows
Opening/Closing the Power Windows
The power windows can be opened and closed when the power mode is in ON,
using the switches on the doors. The driver’s side switches can be used to open and
close all of the windows.
The power window lock button on the driver’s side must be switched off (not
pushed in, indicator off) to open and close the windows from anywhere other than
the driver’s seat.
When the power window lock button is pushed in, you can only operate the driver’s
window. Turn the power window lock button on when children are in the vehicle.
■
Automatic operation
To open: Push the switch down firmly.
To close: Pull the switch up firmly.
The window opens or closes completely. To
stop the window at any time, push or pull the
switch briefly.
■
Manual operation
To open: Push the switch down lightly, and
hold it until the desired position is reached.
To close: Pull the switch up lightly, and hold it
until the desired position is reached.
■
Opening/Closing the Windows with Auto-Open/Close Function
1
Opening/Closing the Power Windows
The power windows can be operated for up to 10
minutes after you set the power mode to VEHICLE
OFF (LOCK).
Opening either front door cancels this function.
Auto Reverse
If a power window senses resistance when closing
automatically, it stops closing and reverses direction.
The driver’s window auto reverse function is disabled
when you continuously pull up the switch.
The auto reverse function stops sensing when the
window is almost closed to ensure that it fully closes.
3
WARNING
Closing a power window on someone’s
hands or fingers can cause serious injury.
Make sure your passengers are away from
the windows before closing them.
ON
OFF
Power Window
Lock Button
Indicator
Driver’s
Window
Switch
Front Passenger’s
Window Switch
Rear Passenger’s
Window Switches
17 ACURA RLX E-AWD-31TY36300.book 152 ページ 2016年6月17日 金曜日 午前8時29分
-------------------------------------------------------------------------------------------------------------------------------------------------------------
153
uu
Opening and Closing the Windows
u
Opening/Closing the Power Windows
Co
ntrols
To open: Press the unlock button twice
within 10 seconds and hold it down the
second time. If the windows stop midway,
repeat the procedure.
To open: Unlock the driver’s door with the
key. Within 10 seconds of returning the key to
the central position, turn the key in the unlock
direction and hold it there.
To close: Lock the driver’s door with the key.
Within 10 seconds of returning the key to the
central position, turn the key in the lock
direction and hold it there.
Release the key to stop the windows/
moonroof at the desired position. If you want
further adjustment, repeat the same
operation.
■
Opening the Windows and Moonroof with the Remote
Unlock
Button
■
Opening/Closing the Windows and Moonroof with the Key
Close
Open
17 ACURA RLX E-AWD-31TY36300.book 153 ページ 2016年6月17日 金曜日 午前8時29分
-------------------------------------------------------------------------------------------------------------------------------------------------------------
154
Co
ntrols
Opening and Closing the Moonroof
You can only operate the moonroof when the power mode is in ON. Use the switch
in the front of the ceiling to open and close the moonroof.
■
Automatic operation
To open: Pull the switch back firmly.
To close: Push the switch forward firmly.
The moonroof will automatically open or close
all the way. To stop the moonroof midway,
touch the switch briefly.
■
Manual operation
To open: Pull the switch back lightly, and
hold it until the desired position is reached.
To close: Push the switch forward lightly, and
hold it until the desired position is reached.
■
Tilting the moonroof up
To tilt: Push on the center of the moonroof
switch.
To close: Push the switch forward firmly, then
release.
■
Opening/Closing the Moonroof
1
NOTICE
Opening the moonroof in below freezing
temperature or when it is covered with snow or ice
can damage the moonroof panel or motor.
The power moonroof can be operated for up to 10
minutes after you set the power mode to VEHICLE
OFF (LOCK).
Opening either front door cancels this function.
When resistance is detected, the auto reverse
function causes the moonroof to change directions,
then stop. Auto reverse stops sensing when the
moonroof is almost closed to ensure that it fully
closes.
3
WARNING
Opening or closing the moonroof on
someone’s hands or fingers can cause
serious injury.
Make sure all hands and fingers are clear of
the moonroof before opening or closing it.
Close
Open
Tilt
17 ACURA RLX E-AWD-31TY36300.book 154 ページ 2016年6月17日 金曜日 午前8時29分
-------------------------------------------------------------------------------------------------------------------------------------------------------------
155
Continued
Co
ntrols
Operating the Switches Around the Steering Wheel
POWER Button
■
Changing the Power Mode
1
POWER Button Operating Range
You can start the power system when the keyless
access remote is inside the vehicle.
The power system may also start if the keyless access
remote is close to the door or window, even if it is
outside the vehicle.
ON mode:
Indicator in the button is off, if the engine is running.
If the keyless access remote battery is weak, beeper
sounds and the To Start, Hold Remote Near Start
Button message appears on the multi-information
display.
2 If the Keyless Access Remote Battery is
Do not leave the power mode in ACCESSORY or ON
when you get out.
Operating Range
VEHICLE OFF (LOCK)
Indicator in the button is off.
The power to all electrical components is turned
off.
Press the button.
Without pressing
the brake pedal
ACCESSORY
Indicator in the button is on.
Operate the audio system and other accessories
in this position.
ON
Indicator in the button is on.
All electrical components can be used.
Indicator
17 ACURA RLX E-AWD-31TY36300.book 155 ページ 2016年6月17日 金曜日 午前8時29分
-------------------------------------------------------------------------------------------------------------------------------------------------------------
156
uu
Operating the Switches Around the Steering Wheel
u
POWER Button
Co
ntrols
If you leave the vehicle for 30 to 60 minutes with the transmission in
(
P and the
power mode in ACCESSORY, the vehicle automatically goes into the mode similar to
VEHICLE OFF (LOCK) to avoid the 12-volt battery drain.
When in this mode, you cannot lock or unlock doors with the remote transmitter or
the keyless access system.
Press the POWER button to switch the mode to VEHICLE OFF (LOCK).
If you open the driver’s door when the power mode is set to ACCESSORY, a warning
buzzer sounds.
■
Automatic Power Off
■
Power Mode Reminder
17 ACURA RLX E-AWD-31TY36300.book 156 ページ 2016年6月17日 金曜日 午前8時29分
-------------------------------------------------------------------------------------------------------------------------------------------------------------
157
uu
Operating the Switches Around the Steering Wheel
u
POWER Button
Co
ntrols
Warning buzzers may sound from inside or/
and outside the vehicle to remind you that the
keyless access remote is out of the vehicle. If
the buzzer continues even after the remote is
put back inside, place it to be within its
operational range.
■
When the power mode is in ON
If the keyless access remote is taken out of the
vehicle, and the driver’s door is closed,
warning buzzers sound from both inside and
outside the vehicle. A warning message on
the multi-information display notifies the
driver inside that the remote is out.
■
When the power mode is in
ACCESSORY
If the keyless access remote is taken out of the
vehicle, and the driver’s door is closed, a
warning buzzer sounds from outside the
vehicle.
■
Keyless Access Remote Reminder
1
Keyless Access Remote Reminder
When the keyless access remote is within the
system’s operational range, and the driver’s door is
closed, the warning function cancels.
If the keyless access remote is taken out of the vehicle
after the power system has been turned on, you can
no longer change the POWER button mode or
restart the power system. Always make sure if the
remote is in your vehicle when you operate the
POWER button.
Removing the keyless access remote from the vehicle
through a window does not activate the warning
buzzer.
Do not put the keyless access remote on the
dashboard or in the glove box. It may cause the
warning buzzer to go off. Under some other
conditions that can prevent the vehicle from locating
the remote, the warning buzzer may also go off even
if the remote is within the system’s operational
range.
17 ACURA RLX E-AWD-31TY36300.book 157 ページ 2016年6月17日 金曜日 午前8時29分
-------------------------------------------------------------------------------------------------------------------------------------------------------------
158
uu
Operating the Switches Around the Steering Wheel
u
Turn Signals
Co
ntrols
Turn Signals
The turn signals can be used when the power
mode is in ON.
■
One-touch turn signal
When you lightly push up or down and release
the turn signal lever, the exterior turn signals
and turn signal indicator blink three times.
This feature can be used when signaling for a
lane change.
Right Turn
Left Turn
17 ACURA RLX E-AWD-31TY36300.book 158 ページ 2016年6月17日 金曜日 午前8時29分
-------------------------------------------------------------------------------------------------------------------------------------------------------------
159
uu
Operating the Switches Around the Steering Wheel
u
Light Switches
Continued
Co
ntrols
Light Switches
Rotating the light switch turns the lights on
and off, regardless of the power mode
setting.
■
High beams
Push the lever forward until you hear a click.
■
Low beams
When in high beams, pull the lever back to
return to low beams.
■
Flashing the high beams
Pull the lever back, and release it.
■
Lights off
Turn the lever to OFF either when:
• The transmission is in
(
P.
• The parking brake is applied.
To turn the lights on again, turn the lever to
OFF to cancel the lights off mode. Even if you
do not cancel the lights off mode, the lights
come on automatically when:
• The gear position is changed out of
(
P.
• The parking brake is released.
• The vehicle starts to move.
■
Manual Operation
1
If you leave the power mode in VEHICLE OFF (LOCK)
with the lights on, a light on reminder chime will
sound when you open the driver’s door.
When the lights are on, the lights on indicator in the
instrument panel will be on.
2 Lights On Indicator P. 85
If you sense that the level of the headlights is
abnormal, have your vehicle inspected by a dealer.
Do not leave the lights on when the power system is
off because it will cause the 12-volt battery to
discharge.
Your vehicle is equipped with the automatic
headlight adjusting system that automatically adjusts
the vertical angle of the headlights. If you find a
significant change in the vertical angle of the
headlights, there may be a problem with the system.
Have your vehicle checked by a dealer.
High Beams
Flashing the high beams
Low Beams
Turns on parking, side marker,
tail, and rear license plate lights
Turns on headlights, parking, side
marker, tail, and rear license plate
lights
17 ACURA RLX E-AWD-31TY36300.book 159 ページ 2016年6月17日 金曜日 午前8時29分
-------------------------------------------------------------------------------------------------------------------------------------------------------------
uu
Operating the Switches Around the Steering Wheel
u
Light Switches
160
Co
ntrols
Automatic lighting control can be used when
the power mode is in ON.
When the light switch is in AUTO, the
headlights and other exterior lights will switch
on and off automatically depending on the
ambient brightness.
You can change the auto light sensitivity
setting.
2 Customized Features P. 113, 283
■
Automatic Lighting Control
1
We recommend that you turn on the lights manually
when driving at night, in a dense fog, or in dark areas
such as long tunnels or parking facilities.
The light sensor is in the location shown below.
Do not cover this light sensor with anything;
otherwise, the automatic lighting system may not
work properly.
Adjust the auto light sensitivity as follows:
2 Customized Features P. 113, 283
Setting
The exterior lights come on
when the ambient light is at
MAX
HIGH
MID
LOW
MIN
Light Sensor
Bright
Dark
17 ACURA RLX E-AWD-31TY36300.book 160 ページ 2016年6月17日 金曜日 午前8時29分
-------------------------------------------------------------------------------------------------------------------------------------------------------------
161
uu
Operating the Switches Around the Steering Wheel
u
Light Switches
Co
ntrols
The headlights automatically come on when the wipers are used several times within
a certain intervals with the headlight switch in AUTO.
The headlights automatically go off a few minutes later if the wipers are stopped.
The headlights, all other exterior lights, and the instrument panel lights turn off 15
seconds after you set the power mode to VEHICLE OFF (LOCK), take the remote with
you, and close the driver's door.
If you set the power mode to VEHICLE OFF (LOCK) with the headlight switch on, but
do not open the door, the lights turn off after 10 minutes (three minutes, if the
switch is in the AUTO position).
The lights turn on again when you unlock or open the driver’s door. If you unlock
the door, but do not open it within 15 seconds, the lights go off. If you open the
driver’s door, you will hear a lights on reminder chime.
■
Headlight Integration with Wipers
*
■
Automatic Lighting Off Feature
1
Headlight Integration with Wipers
This feature activates when the headlights are off in
AUTO.
The instrument panel brightness does not change
when the headlights come on.
At dark ambient light levels, the automatic lighting
control feature turns on the headlights, regardless of
the number of wiper sweeps.
1
Automatic Lighting Off Feature
You can change the headlight auto off timer setting.
2 Customized Features P. 113, 283
* Not available on all models
17 ACURA RLX E-AWD-31TY36300.book 161 ページ 2016年6月17日 金曜日 午前8時29分
-------------------------------------------------------------------------------------------------------------------------------------------------------------
162
uu
Operating the Switches Around the Steering Wheel
u
Fog Lights
Co
ntrols
Fog Lights
When the low beam headlights are on, turn
the fog light switch on to use the fog lights.
Daytime Running Lights
The low beam headlights come on slightly dimmer than normal when the following
conditions have been met:
• The power mode is in ON.
• The headlight switch is AUTO, or in
.
• The parking brake is released.
The low beam headlights return to the original brightness once the headlight switch
is turned on, or when the headlight switch is in AUTO and it is getting darker
outside.
1
The fog lights go off when the headlights turn off, or
when the daytime running lights are on.
Fog Light Switch
1
The daytime running lights come on dimmer when
the headlight switch is in
than when it is in
AUTO. In AUTO, if the ambient brightness is dark,
the low beam headlights come on.
U.S. models
17 ACURA RLX E-AWD-31TY36300.book 162 ページ 2016年6月17日 金曜日 午前8時29分
-------------------------------------------------------------------------------------------------------------------------------------------------------------
163
uu
Operating the Switches Around the Steering Wheel
u
Wipers and Washers
Continued
Co
ntrols
Wipers and Washers
The windshield wipers and washers can be
used when the power mode is in ON.
■
MIST
The wipers run at high speed until you release
the lever.
■
Wiper switch (OFF, LO, HI)
Change the wiper switch setting according to
the amount of rain.
■
AUTO
2 Automatic Intermittent Wipers P. 164
■
Washer
Sprays while you pull the lever toward you.
When you release the lever, the wipers make
two or three more sweeps before stopping.
1
NOTICE
Do not use the wipers when the windshield is dry.
The windshield will get scratched, or the rubber
blades will get damaged.
NOTICE
In cold weather, the blades may freeze to the
windshield, becoming stuck.
Operating the wipers in this condition may damage
them. Use the defroster to warm the windshield,
then turn the wipers on.
If the vehicle speeds up while the wipers are
operating intermittently, the length of the wipe
interval shortens.
When the vehicle starts moving, the wipers make a
single sweep.
Turn the washers off if no washer fluid comes out.
The pump may get damaged.
The wiper motor may stop motor operation
temporarily to prevent an overload. Wiper operation
will return to normal within a few minutes, once the
circuit has returned to normal.
MIST
OFF
LO: Low speed wipe
HI: High speed wipe
Pull to
use
washer.
AUTO: Wiper speed varies
automatically
17 ACURA RLX E-AWD-31TY36300.book 163 ページ 2016年6月17日 金曜日 午前8時29分
-------------------------------------------------------------------------------------------------------------------------------------------------------------
uu
Operating the Switches Around the Steering Wheel
u
Wipers and Washers
164
Co
ntrols
When you push the lever down to AUTO, the
windshield wipers sweep once, and go into
the automatic mode.
The wipers operate intermittently, at low
speed, or at high speed and stops in
accordance with the amount of rainfall the
rainfall sensor detects.
■
AUTO sensitivity adjustment
When in AUTO, you can also adjust the
rainfall sensor sensitivity using the adjustment
ring.
Sensor sensitivity
■
Automatic Intermittent Wipers
1
If the wipers stop operating due to any obstacle such
as the build-up of snow, park the vehicle in a safe
place.
Rotate the wiper switch to OFF, and set the power
mode to ACCESSORY or VEHICLE OFF (LOCK), then
remove the obstacle.
1
The rainfall sensor is in the location shown below.
Do not put the wiper lever in AUTO when cleaning
the windshield or driving through a car wash. If the
wiper lever is in AUTO, and the power mode is in ON,
the rainfall sensor may respond to your hand or car
wash liquids, and the wipers may operate
automatically.
Rainfall Sensor
Adjustment Ring
Low sensitivity:
Lower speed, fewer sweeps
High sensitivity:
Higher speed, more sweeps
17 ACURA RLX E-AWD-31TY36300.book 164 ページ 2016年6月17日 金曜日 午前8時29分
-------------------------------------------------------------------------------------------------------------------------------------------------------------
165
uu
Operating the Switches Around the Steering Wheel
u
Wipers and Washers
Co
ntrols
Turn the headlights on and press the
headlight washer button to operate.
The headlight washers also operate when you
turn the windshield washers for the first time
after the power mode sets to ON.
■
Headlight Washers
Canadian models
1
The headlight washers use the same fluid reservoir as
the windshield washers.
Headlight
Washer
Button
17 ACURA RLX E-AWD-31TY36300.book 165 ページ 2016年6月17日 金曜日 午前8時29分
-------------------------------------------------------------------------------------------------------------------------------------------------------------
166
uu
Operating the Switches Around the Steering Wheel
u
Brightness Control
Co
ntrols
Brightness Control
When the power mode is in ON, you can use
the
(
+ or
(
- button to adjust instrument
panel brightness.
To brighten: Press the
(
+ button.
To dim: Press the
(
- button.
You will hear a beep when the brightness
reaches minimum or maximum. The multi-
information display will return to its original
state several seconds after you adjust the
brightness.
■
Brightness level indicator
The brightness level is shown on the multi-
information display while you are adjusting it.
■
Adjusting the Instrument Panel Brightness
1
Adjusting the Instrument Panel Brightness
Instrument panel brightness varies, depending on
whether the exterior lights are on or off. The
instrument panel dims to reduce glare when they are
on.
When it is bright outside and the headlight
integration with the wiper
*
is activated, the
instrument panel brightness does not change.
Pushing or rolling the right selector wheel changes to
a different display.
If you press the
(
+ button until the brightness display
is up to max, the beeper sounds. This cancels the
reduced instrument panel brightness when the
parking lights are on.
The brightness can be set differently for when the
exterior lights are on, and when they are off.
(
+ Button
(
- Button
* Not available on all models
17 ACURA RLX E-AWD-31TY36300.book 166 ページ 2016年6月17日 金曜日 午前8時29分
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст