Mazda 5 (2017 year). Instruction — part 15
Black plate (232,1)
SIRIUS service uses an ID code to
identify your radio. This code is needed to
activate SIRIUS service, and report any
problems.
To activate you SIRIUS radio tuner, call a
SIRIUS customer service specialist at 1-
888-539-7474 or you can visit SIRIUS
online at www.siriusxm.com.
Please have the following information
ready:
l
SIRIUS ID (12-digit electronic serial
no., or ESN
*
)
l
Valid credit card information (may not
be required at initial sign-up)
*ESN: Electronic Serial Number
Displaying the SIRIUS ID (ESN)
When the manual tuning dial is turned to
channel 0, a 12-digit Electronic Serial
Number (ESN) for the SIRIUS tuner is
displayed.
(If the SIRIUS ID (ESN) for the tuner
does not display)
If
“ESN FAIL” is displayed after channel
0 is selected by operating the manual
tuning dial, contact an Authorized Mazda
Dealer.
Be sure you are parked outside with a
clear view of open sky, you will be
instructed to turn on your radio (in SAT
mode and tuned to channel 184).
Activation typically takes only 2
―5
minutes.
SIRIUS operation
All operations of the satellite radio are
conducted by means of the audio unit.
SIRIUS radio mode selection
When the satellite button (
) is
pressed during ACC ON, it will play the
last SIRIUS channel in use before the
mode was switched over to another mode
or the power was turned off.
When the satellite button (
) is
pressed in a mode other than the SIRIUS
mode, the last channel in use will be
received.
Every time the satellite button (
)
is pressed, the bank changes in the order
shown in the following.
SR2
SR1
SR3
NOTE
SR1, SR2 and SR3: six stations can be stored
in each bank for convenient access to your
favorite stations.
Operation in the initial state
It may take some time to start up the
equipment when it is in the initial state,
when there is a change in the user's
subscription condition, or when the
SIRIUS channel map is changed.
6-34
Interior Comfort
Audio System
Mazda5_8FN4-EA-16G_Edition1 Page232
Monday, May 23 2016 7:35 PM
Black plate (233,1)
“UPDATING xx%” is displayed when the
SIRIUS channel map is changed. If the
unit is initialized or the user contract
content is changed,
“SUBSCRIPTION”
and
“UPDATED” is displayed. Updating
could take as long as three minutes
depending on the geographical area.
When the unit is in an initialized state,
channel 184 is displayed after the display
indicates
“UPDATING 100%”. If the
SIRIUS channel map or the user contract
content is changed, the channel prior to
the change is displayed after
“SUBSCRIPTION” and “UPDATED” is
displayed. After the initialization display,
it may take as long as 12 seconds to
receive channel 184.
NOTE
Do not perform the following operation while
“UPDATING” is displayed. Otherwise, the
updating procedure will be cancelled.
l
Turning off the audio power
l
Switching to other modes
l
Switching the ignition off
When the SIRIUS mode is switched to
another mode, or when the power is
turned off, the present channel which is
being received is stored as the last
channel.
Channel selection
Turning the manual tuning dial allows you
to select the desired receiving channel.
l
Turn the knob clockwise: Channel Up
l
Turn the knob counterclockwise:
Channel Down
Unsubscribed channel
When a selected station has not been
subscribed to, the display indicates the
following:
After the channel number is displayed,
[CALL
888] and [539
SIRI]
(Flashes alternately) is displayed.
NOTE
When the subscription contract is canceled, all
of the channels including channel 184 appear
as unsubscribed.
Invalid channel
The display switches between [SR
(bank number)
INVALID] and [SR
(bank number)
CHANNEL] only when
a selected channel is not broadcasting.
NOTE
If the last channel selected has become
unavailable because of a channel update the
above indication is displayed until any button
is pressed.
Preset channel programming
(Programming with
“channel number”
display)
1. Select the desired channel to be
programmed. At this point, the
following is displayed:
[SR
(bank number)
(channel
number)]
2. Keep pressing the channel preset
button for 1.5 seconds or more.
The programming process is complete
after the channel number flashes. Then,
[SR
(bank number)] is displayed
and a beep sound is heard at the same
time.
3. [SR
(bank number)
CH
(preset number)
(channel number)]
are displayed.
Interior Comfort
Audio System
6-35
Mazda5_8FN4-EA-16G_Edition1 Page233
Monday, May 23 2016 7:35 PM
Black plate (234,1)
(Programming with
“text” display (e.g.
channel name))
1. Select the desired channel to be
programmed. At this point, the
following is displayed:
[SR
(bank number)
(selected text
(e.g. channel name))]
2. Keep pressing the channel preset
button for 1.5 seconds or more.
The programming process is complete
after the text (e.g. channel name)
flashes. Then, [SR
(bank number)]
is displayed and you will hear beep
sound at the same time.
3. [SR
(bank number)
CH
(preset number)
(channel number)]
are displayed.
4. Three seconds later, it returns to normal
display. [SR
(bank number)
(text
(e.g. channel name))]
NOTE
Six stations can be stored in each bank, SR1,
SR2, and SR3 for convenient access to your
favorite stations.
Preset channel call-up
Press and release the channel preset
button,
[SR
(bank number)
CH
(preset
number)
(channel number)] appears.
When the preset button is pressed during
text mode, its channel number is
displayed first for three second and then
its text is displayed.
NOTE
In the initial setting, all channels are preset to
184.
Category change
Press the category button (
or
) and
select the desired category.
l
Press the category button (
):
Category up
l
Press the category button (
):
Category down
Every time the category button (
) is
pressed, the category is changed over in
the order shown in the following.
At this time, the lowest (smallest-number)
channel within the category indicated is
received.
When the highest (or lowest) category is
reached, the category is changed over in
the order shown in the following.
Highest category
→ All categories →
Lowest category
NOTE
While all categories are selected, all channels
covering a category can be accessed
(Category off condition).
Channel selection within a category
If you are in a selected category and the
channel number is displayed, turning the
manual tuning dial moves the channel
number up/down in that category.
l
Turn the manual tuning dial clockwise:
Channel Up
l
Turn the manual tuning dial
counterclockwise: Channel Down
NOTE
The channel number needs to be indicated in
the display to use manual tuning dial for this
function.
6-36
Interior Comfort
Audio System
Mazda5_8FN4-EA-16G_Edition1 Page234
Monday, May 23 2016 7:35 PM
Black plate (235,1)
Scan tuning
Press the scan button (
) to
automatically sample stations. Scanning
stops at each station for about five
seconds. To hold a station, press the scan
button (
) again during this interval.
NOTE
l
Unsubscribed channels, invalid channels,
parental lock channels and channel 0 are
not subject to the scan, therefore these
channels will be skipped automatically.
l
You can scan all channels while all
categories are selected. If you are in a
selected category, you can only scan the
channels in that category.
Channel number, channel name,
category, artist, song titles and info
display
Each time the text button (
) is
pressed during SIRIUS reception, the
display of the text data is changed over in
the order shown in the following.
Channel number
Channel name
Category
name
Artist name
Info
Song title
NOTE
l
Eight characters are displayed on one
screen.
l
To display the rest of the characters of a
long title, press the scroll button (
).
The display scrolls the next eight
characters. Press the scroll button (
)
again after the last eight characters have
been displayed to return to the beginning of
the title.
(Channel number display)
l
When the text button (
) is
pressed while in info display mode, the
mode changes to the channel number
display mode.
(Channel name display)
l
When the text button (
) is
pressed while in channel number
display mode, it changes to channel
name display mode.
l
There are short (eight fixed characters)
and long names for the channel name.
l
The long name is displayed first, and
three seconds later the short name is
displayed. If there is no short name, the
long name is displayed.
l
To display the rest of the characters of
the channel name, press the scroll
button (
). The display scrolls the
next eight characters. Press the scroll
button (
) again after the last eight
characters have been displayed to
return to the beginning of the title.
l
Press the scroll button (
) while
the short name is displayed to switch
the display to the long name.
l
Three seconds after scrolling the long
name, the display automatically returns
to the first part of the long name. Three
more seconds and the short name
appears.
Interior Comfort
Audio System
6-37
Mazda5_8FN4-EA-16G_Edition1 Page235
Monday, May 23 2016 7:35 PM
Black plate (236,1)
l
If there is no channel name,
“No TITLE” is displayed.
(Category name display)
l
When the text button (
) is
pressed while in channel name display
mode, it changes to the category name
display mode.
l
There are short (eight fixed characters)
and long names for the category name.
l
The long name is displayed first, and
three seconds later the short name is
displayed. If there is no short name, the
long name is displayed.
l
To display the rest of the characters of
the category name, press the scroll
button (
). The display scrolls the
next eight characters. Press the scroll
button (
) again after the last eight
characters have been displayed to
return to the beginning of the title.
l
Press the scroll button (
) while
the short name is displayed to switch
the display to the long name.
l
Three seconds after scrolling the long
name, the display automatically returns
to display the first part of the long
name. Three more seconds and the
short name appears.
l
If there is no category name,
“No CATEGORY” is displayed.
(Artist name display)
l
When the text button (
) is
pressed while in category name display
mode, it changes to the artist name
display mode.
l
To display the rest of the characters of
the artist's name, press the scroll button
(
). The display scrolls the next
eight characters. Press the scroll button
(
) again after the last eight
characters have been displayed to
return to the beginning of the title.
l
Three seconds after scrolling the artist
name, the display automatically return
to display the first part of the artist's
name.
l
If there is no artist's name,
“No ARTIST” is displayed.
(Song title display)
l
When the text button (
) is
pressed while in artist name display
mode, it changes to the song title
display mode.
l
To display the rest of the characters of
the song title, press the scroll button
(
). The display scrolls the next
eight characters. Press the scroll button
(
) again after the last eight
characters have been displayed to
return to the beginning of the title.
l
Three more seconds after scrolling the
song title, the display automatically
returns to display the first part of the
song title.
l
If there is no song title,
“No SONG” is
displayed.
(INFO (such as composer's name)
display)
l
When the text button (
) is
pressed while in song title display
mode, it changes to the INFO display
mode.
l
To display the rest of the characters of
the composer's name, press the scroll
button (
). The display scrolls the
next eight characters. Press the scroll
button (
) again after the last eight
characters have been displayed to
return to the beginning of the title.
l
Three seconds after scrolling the text,
the display automatically returns to
display the first part of the text.
l
If there is no composer name,
“No INFO” is displayed.
6-38
Interior Comfort
Audio System
Mazda5_8FN4-EA-16G_Edition1 Page236
Monday, May 23 2016 7:35 PM
Black plate (237,1)
Instant replay
This function allows you to rewind and
replay the program that you were
previously or are currently listening to.
Press the instant replay button (
).
When the seek tuning button (
) is
pressed (about 1.5 seconds), playback
starts from the beginning of the current
program.
When the seek tuning button (
) is
pressed twice, playback starts from the
beginning of the previous program.
When the seek tuning button (
) is
pressed for about 1.5 seconds or longer,
the program is reversed while the button
is being pressed.
When the seek tuning button (
) is
pressed (about 1.5 seconds), playback
starts from the beginning of the next
program. When the seek tuning button
(
) is pressed (about 1.5 seconds) while
the last program is being played, the
instant replay mode is cancelled.
When the seek tuning button (
) is
pressed for 1.5 seconds or longer, the
program is fast-forwarded while the
button is being pressed. When pressing
and holding the button until the end of the
program, the instant replay mode is
cancelled.
When the instant replay button (
) is
pressed again, playback is paused, or
playback starts if it has been paused.
Instant replay (PAUSE)
If the instant replay button (
) is
pressed while the instant replay mode is
off, instant replay mode is turned on in a
paused condition (PAUSE). Press the
instant replay button (
) again to
resume playback from the point at which
it was paused.
NOTE
l
If the channel is changed, the instant replay
buffer data is deleted.
l
After turning on the power and switching to
SIRIUS digital satellite radio mode, the
instant replay mode is not available for
several seconds after changing channels.
Initialization of ID code
If the registered ID code is forgotten,
return the ID code to the default [0000] by
performing the following steps:
Setting condition: SAT mode
(Master code input preparation)
1. Press and hold the scan button (
),
then press channel preset button 4.
Hold both buttons together for 1.5
seconds.
2.
“ENTER PIN” appears for three
seconds which indicates that it is in
code input mode.
3.
“SR1 - - - -” appears, which indicates
that it is ready for code input.
(Master code input)
4. Input the master code using the channel
preset buttons 1-4.
(The master code is already set at the
time of factory shipment.)
(Master code input determination)
5. Determine the master code which has
been input by pressing the scan button
(
).
6.
“PIN CLEARED” appears which
indicates that the master code input has
been completed.
7. The ID code is set to the default [0000]
and the initialization process is
completed.
Interior Comfort
Audio System
6-39
Mazda5_8FN4-EA-16G_Edition1 Page237
Monday, May 23 2016 7:35 PM
Black plate (238,1)
NOTE
Master code:
The Master Code is used to initialize or re-
initialize the ID code in the event that the code
is not set to [0000] and/or the personalized ID
code is not known. The initialization process
resets the ID code to [0000]. The master code
can potentially defeat the intent of the security
of the parental lock if it is located by persons
not authorized by the owner to access certain
channels.
SIRIUS Satellite Radio Master Code: [0913]
NOTE
l
When a numeric value other than the
master code is input and the scan button
(
) is pressed,
“SR1 Err” is displayed
and then it returns to the
“SR1 - - - -”
display again.
l
If an ID code is not input for ten seconds,
“Err” is displayed and it returns to the
former display.
l
Channel preset buttons 1, 2, 3, 4 and the
scan button (
) are used for inputting
the ID code. Buttons 5 and 6 cannot be
used.
Change of ID code
Setting condition: SAT mode
When changing the ID code, the new ID
code is input after the previous one is
input first.
(Registered ID code input)
1. Press and hold the scan button (
),
then press channel preset button 5.
Hold both buttons together for 1.5
seconds.
2.
“ENTER PIN” appears for three
seconds which indicates that it is in
code input mode.
3.
“SR1 - - - -” appears, which indicates
that it is ready for code input.
4. Input the registered ID code using
channel preset buttons 1-4.
Example: When the registered ID code
is
“2323”, input “2323”. At this time
“SR1 2323” is displayed.
Press 1 for the first digit, 2 for the
second, 3 for the third, and 4 for the
last digit. For example, if your number
is 2323, press 1 three times (includes
0), 2 four times, 3 three times, and 4
four times. If the display goes off while
inputting, begin from Step 1.
NOTE
The registered ID code is the default [0000] at
the time of factory shipment. If [0000] results
in
“Err” on the display, go to the
“INITIALIZATION OF ID CODE” section to
reset to [0000].
(Verification with the registered ID
code)
5. Determine the input code by pressing
the scan button (
).
6. If it does not match with the previously
registered code,
“SR1 Err” is displayed
and then it returns to
“SR1 - - - -”.
7. If it matches with the previously
registered code,
“ENTER PIN” appears
again and it switches to code input
mode.
8.
“SR1 - - - -” appears, and it is ready for
input of the new ID code.
(New ID code input)
9. Input the new ID code using channel
preset buttons 1-4.
Example: If
“1234” is input as the new
code,
“SR1 1234” is displayed.
6-40
Interior Comfort
Audio System
Mazda5_8FN4-EA-16G_Edition1 Page238
Monday, May 23 2016 7:35 PM
Black plate (239,1)
(New ID code input determination)
10. Determine the new ID code which
has been input by pressing the scan
button (
).
11.
“PIN CHANGED” appears for three
seconds which indicates that the new
ID code input has been completed.
12. It returns to the former display.
NOTE
l
If an ID code is not input for ten seconds,
“Err” is displayed and it returns to the
former display.
l
Channel preset buttons 1, 2, 3, 4 and the
scan button (
) are used for input of
the ID code. Buttons 5 and 6 cannot be
used.
Individual channel locking
If a channel is locked, the channel is
muted.
NOTE
If the registered ID code is forgotten, return
the ID code to the default [0000]. (See
“INTIALIZATION OF ID CODE” section)
(Locking a channel)
1. Select a channel to be locked by
turning the manual tuning dial.
Example: Select channel 100
(Registered ID code input preparation)
2. Press and hold the scan button (
),
then press channel preset button 6.
Hold both buttons together for 1.5
seconds.
3.
“ENTER PIN” appears for three
seconds which indicates that it is in
code input mode.
4.
“SR1 - - - -” appears which indicates
that it is ready for code input.
(Registered ID code input)
5. Input the registered ID code using
channel preset buttons 1-4. Example: If
the registered ID code is
“2323”, input
“2323”. At this time “SR1 2323” is
displayed.
(Registered ID code input
determination)
6. Determine the code which has been
input by pressing the scan button
(
).
7. If it does not match the registered code,
“SR1 Err” is displayed and then it
returns to
“SR1 - - - -”.
8. If it matches the registered code,
“SR1 LOCK” appears for three
seconds which indicates that the code
input has been completed.
9.
“SR1 LOCK 100” appears which
indicates that the parental lock is
activated. At this time, mute is on and
no sound is heard.
NOTE
l
If an ID code is not input for ten seconds,
“Err” is displayed and it returns to the
former display.
l
Channel preset buttons 1, 2, 3, 4 and the
scan button (
) are used for input of
the ID code. Buttons 5 and 6 cannot be
used.
Lock cancellation
Setting condition: SAT mode
(Releasing a locked channel)
1. Select a channel to be released by
turning the manual tuning dial.
Example: Select the locked channel
(i.e. 100). At this time,
“SR1 LOCK 100” is displayed.
Interior Comfort
Audio System
6-41
Mazda5_8FN4-EA-16G_Edition1 Page239
Monday, May 23 2016 7:35 PM
Black plate (240,1)
(Registered ID code input preparation)
2. Press and hold the scan button (
),
then press channel preset button 6.
Hold both buttons together for 1.5
seconds.
3.
“ENTER PIN” appears for three
seconds which indicates that it is in
code input mode.
4.
“SR1 - - - -” appears, which indicates
that it is ready for code input.
(Registered ID code input)
5. Input the registered ID code using
channel preset buttons 1-4. Example:
When the registered ID code is
“2323”,
input
“2323”. At this time “SR1 2323”
is displayed.
NOTE
If
“Err” is displayed, go to the
“INITIALIZATION OF ID CODE” section to
reset the ID code to [0000].
(Registered ID code input
determination)
6. Determine the input code by pressing
the scan button (
).
7. If it does not match the registered code,
“SR1 Err” is displayed and then it
returns to
“SR1 - - - -”.
8. If it matches the registered code,
“SR1 UNLOCK” appears for three
seconds which indicates that the code
input has been completed.
9.
“SR1 100” appears which indicates that
the parental lock is off. At this time,
sound is heard.
NOTE
l
If an ID code is not input for ten seconds,
“Err” is displayed and it returns to the
former display.
l
Channel preset buttons 1, 2, 3, 4 and the
scan button (
) are used for input of
the ID code. Buttons 5 and 6 cannot be
used.
6-42
Interior Comfort
Audio System
Mazda5_8FN4-EA-16G_Edition1 Page240
Monday, May 23 2016 7:35 PM
Black plate (241,1)
MEMO
6-43
Mazda5_8FN4-EA-16G_Edition1 Page241
Monday, May 23 2016 7:35 PM
Black plate (242,1)
qOperating the Compact Disc (CD) Player
Track down/Reverse button
Scroll button
Play/Pause button/File dial
Random button
CD slot
CD play button
Folder down button
Text button
Scan button
Folder up button
Repeat button
Track up/Fast-forward button
Load button
CD eject button
Type
Playable data
Music/MP3/WMA/
AAC CD player
l
Music data (CD-DA)
l
MP3/WMA/AAC file
NOTE
If a disc has both music data (CD-DA) and
MP3/WMA/AAC files, playback of the two or
three file types differs depending on how the
disc was recorded.
Inserting the CD
Insert the CD into the slot, label-side up.
The auto-loading mechanism will set the
CD and begin play.
NOTE
There will be a short lapse before play begins
while the player reads the digital signals on
the CD.
Ejecting the CD
Press the CD eject button (
) to eject the
CD.
Playback
Press the CD play button (
) to start
play when a CD is in the unit.
If a CD is not in the unit when the CD
play button (
) is pressed,
“NO DISC”
will flash on and off.
NOTE
When the load button (
) is pressed, the
CD will load and play even if the CD eject
button (
) had been previously pressed.
Pause
To stop playback, press the Play/Pause
button (
).
Press the button again to resume
playback.
6-44
Interior Comfort
Audio System
Mazda5_8FN4-EA-16G_Edition1 Page242
Monday, May 23 2016 7:35 PM
Black plate (243,1)
Fast-forward/Reverse
Press and hold the fast-forward button
(
) to advance through a track at high
speed.
Press and hold the reverse button (
) to
reverse through a track at high speed.
Track search
Press the track up button (
) or turn the
file dial clockwise once to skip forward to
the beginning of the next track.
Press the track down button (
) or turn
the file dial counterclockwise once to skip
back to the beginning of the current track.
Folder search (during MP3/WMA/AAC
CD playback)
To change to the previous folder, press the
folder down button (
), or press the
folder up button (
) to advance to the
next folder.
Music scan
During music CD playback
This function scans the titles on a CD and
plays 10 seconds of each song to aid you
in finding a song you want to listen to.
During MP3/WMA/AAC CD playback
This function scans the titles in a folder
currently being played and plays 10
seconds of each song to aid you in finding
a song you want to listen to.
Press the scan button (
) during
playback to start the scan play operation
(the track number will flash).
Press the scan button (
) again to
cancel scan playback.
NOTE
If the unit is left in scan, normal playback will
resume where scan was selected.
Repeat playback
During music CD playback
1. Press the repeat button (
) during
playback to play the current track
repeatedly.
“RPT” is displayed.
2. Press the button again to cancel the
repeat playback.
During MP3/WMA/AAC CD playback
(Track repeat)
1. Press the repeat button (
) during
playback to play the current track
repeatedly.
“TRACK RPT” is
displayed.
2. To cancel the repeat playback, press the
button again after 3 seconds.
(Folder repeat)
1. Press the repeat button (
) during
playback, and then press the button
again within 3 seconds to play the
tracks in the current folder repeatedly.
“FOLDER RPT” is displayed.
2. Press the button again to cancel the
repeat playback.
Random playback
Tracks are randomly selected and played.
During music CD playback
1. Press the random button (
) during
playback to play the tracks on the CD
randomly.
“RDM” is displayed.
2. Press the button again to cancel the
random playback.
Interior Comfort
Audio System
6-45
Mazda5_8FN4-EA-16G_Edition1 Page243
Monday, May 23 2016 7:35 PM
Black plate (244,1)
During MP3/WMA/AAC CD playback
(Folder random)
1. Press the random button (
) during
playback to play the tracks in the folder
randomly.
“FOLDER RDM” is
displayed.
2. To cancel the random playback, press
the button again after 3 seconds.
(CD random)
1. Press the random button (
) during
playback, and then press the button
again within 3 seconds to play the
tracks on the CD randomly.
“DISC RDM” is displayed.
2. Press the button again to cancel the
random playback.
Switching the display
For files with a file name and other
information that have been input, the
display switches between display of the
file name and other information each time
the text button (
) is pressed during
playback.
Music CD (If CD-TEXT capable)
Track number/Elapsed time
Track name
Track number
Album name
Artist name
MP3/WMA/AAC CD
File name
Folder name
Album name (ID3 Tag)
Song name (ID3 Tag)
Artist name (ID3 Tag)
Folder number/File number
File number/Elapsed time
NOTE
l
The information viewable in the display is
only CD information (such as artist name,
song title) which has been recorded to the
CD.
l
This unit cannot display some characters.
Characters which cannot be displayed are
indicated by an asterisk (
).
Display scroll
Only 12 characters can be displayed at
one time.
To display the rest of the characters of a
long title, press the scroll button (
).
The display scrolls the next 12 characters.
Press the scroll button (
) again after
the last 12 characters have been displayed
to return to the beginning of the title.
NOTE
The number of characters which can be
displayed is limited.
6-46
Interior Comfort
Audio System
Mazda5_8FN4-EA-16G_Edition1 Page244
Monday, May 23 2016 7:35 PM
Black plate (245,1)
Message display
If
“CHECK CD” is displayed, it means
that there is some CD malfunction. Check
the CD for damage, dirt, or smudges, and
then properly reinsert. If the message
appears again, take the unit to an
Authorized Mazda Dealer for service.
qOperating the Auxiliary jack/
USB port
Audio can be heard from the vehicle's
speakers by connecting a commercially-
available portable audio unit to the
auxiliary jack.
Use a commercially-available, non-
impedance (3.5 ) stereo mini plug cable.
Contact an Authorized Mazda Dealer for
details.
In addition, audio can be played from the
vehicle's audio unit by connecting USB
device or an iPod to the USB port.
Refer to AUX/USB/iPod Mode on page
6-52.
Interior Comfort
Audio System
6-47
Mazda5_8FN4-EA-16G_Edition1 Page245
Monday, May 23 2016 7:35 PM
Black plate (246,1)
qError Indications
If you see an error indication on the display, find the cause in the chart. If you cannot clear
the error indication, take the vehicle to an Authorized Mazda Dealer.
Indication
Cause
Solution
ACQUIRING
Depending on the
surrounding conditions
(such as large trees, build-
ings, or tunnels) and special
weather conditions,
SIRIUS radio reception
may be diminished or
temporarily interrupted.
Improve reception by moving away from possible
obstructions. If the error indication continues to display,
consult an Authorized Mazda Dealer.
ANTENNA FAIL
Satellite radio antenna
malfunction
Check the satellite radio antenna, antenna cable and
DLP antenna connector. If the error indication continues
to display, consult an Authorized Mazda Dealer.
CHECK CD
CD is inserted upside down
Insert the CD properly. If the error indication continues
to display, consult an Authorized Mazda Dealer.
CD is defective
Insert another CD properly. If the error indication
continues to display, consult an Authorized Mazda
Dealer.
NOTE
If a broken DLP* unit is replaced with a new unit, cancel the license for the broken unit and make
sure to carry out new registration for the replaced unit. If the license for the broken unit is not
canceled, you will be charged a reception fee for both units.
* DLP: Down Link Processor (SATELLITE RADIO Module)
6-48
Interior Comfort
Audio System
Mazda5_8FN4-EA-16G_Edition1 Page246
Monday, May 23 2016 7:35 PM
Black plate (247,1)
Audio Control Switch
Operation
When the audio unit is turned on,
operation of the audio unit from the
steering wheel is possible.
NOTE
Because the audio unit will be turned off under
the following conditions, the switches will be
inoperable.
l
When the ignition is switched off.
l
When the power button on the audio unit is
pressed and the audio unit is turned off.
Without Bluetooth® Hands-Free
With Bluetooth® Hands-Free
Talk button
Hang-up
button
Pick-up button
NOTE
l
The talk button, pick-up button, and hang-
up button are operable with the audio unit
turned off.
l
Mazda has installed this system to prevent
distraction while driving the vehicle and
using audio controls on the dashboard.
Always make safe driving your first priority.
qAdjusting the Volume
To increase the volume, press up the
volume switch.
To decrease the volume, press down the
volume switch.
Without Bluetooth® Hands-Free
With Bluetooth® Hands-Free
Interior Comfort
Audio System
6-49
Mazda5_8FN4-EA-16G_Edition1 Page247
Monday, May 23 2016 7:35 PM
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст