Mazda CX 7. Manual — part 376
![](/vehicles/rke/eetan/dot/quptis.png)
BODY PANELS
09-10–11
09-10
Height Adjustment
1. Measure the height difference between the hood and body.
Clearance
a: 2.8— 5.8 mm {0.11— 0.22 in}
b: 3.0— 6.0 mm {0.12— 0.23 in}
c: 2.0— 5.5 mm {0.07— 0.21 in}
d: -1.2— 1.2 mm {-0.04— 0.04 in}
2. Turn the stop rubber to adjust.
End Of Sie
WM: SHROUD PANEL
SEC. A—A
a
b
c
HOOD
SEC. B—B
SEC. D—D
SEC. C—C
SEC. E—E
d
HOOD
FRONT FENDER
PANEL
HOOD
HOOD
RADIATOR
GRILLE
FRONT COMBINATION
LIGHT
b
HOOD
BUMPER
RADIATOR
GRILLE
A
A
B
B
C
C
D
D
E
E
acxuuw00001321
BODY SIDE
STOP RUBBER
STOP RUBBER
DOWN
DOWN
UP
UP
HOOD SIDE
acxuuw00001322
![](/vehicles/rke/eetan/dot/ber.png)
BODY PANELS
09-10–12
SHROUD PANEL REMOVAL/INSTALLATION
id091000801900
1. Disconnect the negative battery cable.
2. Remove the following parts:
(1) Front bumper. (See09-10-2 FRONT BUMPER REMOVAL/INSTALLATION)
(2) Front combination lights. (See09-18-5 FRONT COMBINATION LIGHT REMOVAL/INSTALLATION)
(3) Front bumper reinforcement. (See09-10-4 FRONT BUMPER REINFORCEMENT REMOVAL/
INSTALLATION)
(4) Hood latch. (See09-14-25 HOOD LATCH AND RELEASE LEVER REMOVAL/INSTALLATION)
(5) Hood stay. (See09-10-9 HOOD REMOVAL/INSTALLATION)
3. Put the oil cooler aside.
4. Remove in the order indicated in the table.
5. Install in the reverse order of removal.
Upper Mount Rubber Bracket
1. Remove the upper mount rubber bracket while
pressing down the upper mount rubber bracket
tab in the direction of the arrow.
End Of Sie
WM: COWL UPPER PLATE
1
Bolt A
2
Bolt B
3
Bumper bracket
4
Upper mount rubber bracket
5
Upper mount rubber
6
Bolt C
7
Shroud panel
B
B
2
2
7
4
4
3
6
5
5
6
3
1
1
acxuuw00001323
A
A
FRONT
UPPER MOUNT
RUBBER BRACKET
SHROUD PANEL
ENGINE
COMPARTM
ENT SIDE
TAB
SEC. A—A
acxuuw00001324
![](/vehicles/rke/eetan/dot/ews.png)
BODY PANELS
09-10–13
09-10
COWL PANEL REMOVAL/INSTALLATION
id091000802000
1. Disconnect the negative battery cable.
2. Remove the following parts:
(1) Windshield wiper arm and blade. (See09-19-3 WINDSHIELD WIPER ARM AND BLADE REMOVAL/
INSTALLATION)
(2) Cowl grill. (See09-16-11 COWL GRILLE REMOVAL/INSTALLATION)
3. Remove the bolts, then remove the cowl panel.
4. Install in the reverse order of removal.
End Of Sie
COWL PANEL
6.9—9.8 N·m
{70.4—99.9 kgf·cm,
62—86 in·lbf}
BOLT :
acxuuw00001325
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст