Mazda CX 7. Manual — part 164
![](/vehicles/rke/eetan/dot/itersol.png)
FRONT SUSPENSION
02-13–11
02-13
Tie-rod End Ball Joint Removal Note
1. Remove the tie-rod end ball joint locknut.
2. Disconnect the tie-rod end ball joint using the
SST.
Steering Gear And Linkage, Front Stabilizer, Front Lower Arm And Front Crossmember Component
Removal Note
1. Support the crossmember component with a jack.
2. Loosen the bolts of the No.1 engine mount
(engine side).
3. Remove the No.1 engine mount bolt (engine
side).
4. Lower the steering gear and linkage, front
stabilizer, front lower arm and front crossmember
component slightly.
49 T028 3A0
ampjjw00003208
acxuuw00001339
acxuuw00001689
acxuuw00001690
1871-1U-06B(02-13).fm 11 ページ 2006年3月15日 水曜日 午前11時0分
![](/vehicles/rke/eetan/dot/tinonoony.png)
FRONT SUSPENSION
02-13–12
5. Disconnect the return hose indicated in the figure.
6. Disconnect the pressure hose (power steering
pump side) indicated in the figure.
Front Crossmember Mounting Rubber (front) Installation Note
1. Install the front crossmember mounting rubber
(front) so that the smaller outer diameter is facing
upward.
Front Crossmember Mounting Rubber (rear) Installation Note
1. Install the front crossmember mounting rubber
(rear) so that the larger outer diameter is facing
upward.
acxuuw00001691
FoMoCo
UPPER SIDE OF THE VEHICLE
acxuuw00001341
FoMoCo
UPPER SIDE OF THE VEHICLE
acxuuw00001342
1871-1U-06B(02-13).fm 12 ページ 2006年3月15日 水曜日 午前11時0分
![](/vehicles/rke/eetan/dot/thamer.png)
FRONT SUSPENSION
02-13–13
02-13
Steering Gear And Linkage, Front Stabilizer, Front Lower Arm And Front Crossmember Component
Installation Note
1. Raise the steering gear and linkage, front
stabilizer, front lower arm and front crossmember
component to the appropriately level, and install
the return hose and pressure hose.
Tightening torque
Return hose: 7.8— 10.8 N·m {80— 110
kgf·cm, 69.1— 95.5 in·lbf}
Pressure hose (power steering pump side):
29.4— 44.1 N·m {3.00— 4.49 kgf·m, 21.7—
32.5 ft·lbf}
2. Temporarily install the No.1 engine mount bolt A
indicated in the figure.
3. Tighten the No.1 engine mount bolts B indicated
in the figure.
Tightening torque
93.1— 116.6 N·m {9.50— 11.8 kgf·m, 68.7—
85.9 ft·lbf}
4. Teighten the No.1 engine mount bolt A at the
specified torque.
Tightening torque
85.3— 116.6 N·m {8.70— 11.8 kgf·m, 63.0—
85.9 ft·lbf}
5. Install the steering gear and linkage, front stabilizer, front lower arm and front crossmember component.
6. Tighten the No.1 engine mount bolt (crossmember side).
End Of Sie
WM: TRANSVERSE MEMBER
acxuuw00001691
A
B
acxuuw00001692
1871-1U-06B(02-13).fm 13 ページ 2006年3月15日 水曜日 午前11時0分
![](/vehicles/rke/eetan/dot/ond.png)
FRONT SUSPENSION
02-13–14
TRANSVERSE MEMBER REMOVAL/INSTALLATION
id021300801100
1. Remove the transverse member.
2. Install the transverse member so that the arrow is
pointing to the front of the vehicle.
3. Tighten the nut A, then tighten the bolts in the
order of B, C to the specified torque.
Tightening torque
Nut A: 119.6— 154.8 N·m {12.20— 15.78
kgf·m, 88.3— 114.1 ft·lbf}
Bolts B and C: 93.1— 131.3 N·m {9.50—
13.38 kgf·m, 68.67— 96.84 ft·lbf}
End Of Sie
N·m {kgf·m, ft·lbf}
93.1—131.3
{9.50—13.38,
68.67—96.84}
93.1—131.3
{9.50—13.38,
68.67—96.84}
119.6—154.8
{12.20—15.78,
88.3—114.1}
119.6—154.8
{12.20—15.78,
88.3—114.1}
TRANSVERSE
MEMBER
acxuuw00001674
FRONT
acxuuw00001675
B
C
A
acxuuw00001676
1871-1U-06B(02-13).fm 14 ページ 2006年3月15日 水曜日 午前11時0分
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст