Mazda 6. Manual — part 334

AUDIO AND NAVIGATION SYSTEM

T–95

T

5. With the code number displayed, press the

AUTO-M button, then simultaneously press
channel button 6 for approximately 2 seconds.
“CODE” will be displayed for approximately 5
seconds. After it disappears, the code number is
canceled.

6. If “Err” (error) appears on the display, repeat the

procedure from Step 4.

Canceling Anti-theft Operation
Properly input the selected code number to deactivate the anti-theft system and resume normal audio operation.

1. Turn the ignition switch to ACC position. (“CODE” will flash on the display.)
2. First press the AUTO-M button, then

simultaneously press channel button 6 for
approximately 2 seconds until bars appears on
the display.

Note

• Perform Step 3 within 10 seconds after

Step 2.

3. Use channel buttons 1–4 to input the selected

code number. Press button 1 for the first digit, 2
for the second, 3 for the third, and 4 for the last
digit. Input the number within 10 seconds. If the
display is deleted, repeat the procedure from Step
1.

Caution

• Three consecutive errors, including

turning the ignition switch to LOCK
position and disconnecting the audio
unit, will activate the anti-theft system
and render the audio unit completely
inoperative.

4. With the code number displayed, press the

AUTO-M button, then simultaneously press
channel button 6 for approximately 2 seconds.
“CODE” will flash for approximately 5 seconds..

5. If “Err” (error) appears on the display, repeat the

procedure from Step 1.

End Of Sie

A6E8124W025

A6E8124W026

A6E8124W027

A6E8124W025

T–96

AUDIO AND NAVIGATION SYSTEM

CENTER PANEL MODULE REMOVAL/INSTALLATION

A6E812466900W02

1. Cancel the anti-theft operation. (with anti-theft system) (See

T–93 ANTI-THEFT SYSTEM

.)

2. Disconnect the negative battery cable.
3. Remove the glove compartment.
4. Remove the rear console.
5. Remove in the order indicated in the table.

6. Install in the reverse order of removal.

Caution

• Make certain that the wiring harness and

antenna feeder are not caught between
the unit and dashboard. If the harness or
the antenna feeder is caught between the
unit and dashboard, it may cause trouble
or malfunctions.

7. Operate the anti-theft system by setting the code number. (with anti-theft system) (See

T–93 ANTI-THEFT

SYSTEM

.)

Center Panel Module Removal Note

1. Pull the center panel module toward you, then

disengage clip A from the dashboard, and remove
the center panel module.

End Of Sie

1

Dial (manual A/C only)

2

Screw (manual A/C only)

3

Screw

4

Bolt

5

Center panel module
(See

T–96 Center Panel Module Removal Note

)

6

Connector

7

Antenna feeder

A6E8124W020

A6E8124W029

AUDIO AND NAVIGATION SYSTEM

T–97

T

CENTER PANEL MODULE DISASSEMBLY/ASSEMBLY

A6E812466900W03

Caution

• Before disassembling the center panel module, spread a cloth on the floor to put the

disassembled parts on. This protects the surface of the panel from scratches or dirt.

1. Remove the center panel module. (See

T–96 CENTER PANEL MODULE REMOVAL/INSTALLATION

.)

2. Remove in the order indicated in the table.

3. Install in the reverse order of removal.

End Of Sie

AUDIO UNIT DISASSEMBLY/ASSEMBLY

A6E812466900W04

1. Remove the audio unit. (See

T–97 CENTER PANEL MODULE DISASSEMBLY/ASSEMBLY

.)

2. Disassemble in the order indicated in the table.

3. Assemble in the reverse order of disassembly.

End Of Sie

1

Screw

2

Audio unit

3

Screw

4

Circuit board (manual A/C only)

5

Cover (upper module)

6

Cover (lower module)

7

Passenger-side air bag cut indicator light bulb

8

Socket

9

Screw

10

Bracket

11

Screw

12

Climate control unit (auto A/C only)

13

Screw

14

Ventilator grille

15

Center panel

A6E8124W012

1

Cover (without upper module)

2

Screw

3

Upper module

4

Screw

5

Lower module

6

Screw

7

Wiring harness

8

Base unit

A6E8124W013

T–98

AUDIO AND NAVIGATION SYSTEM

CAR-NAVIGATION UNIT REMOVAL/INSTALLATION

A6E812466902W01

1. Disconnect the negative battery cable.
2. Remove the glove compartment.
3. Remove in the order indicated in the table.

4. Install in the reverse order of removal.

Car-navigation Unit Installation Note

1. Insert the car-navigation unit bracket into the

dashboard member hole, and with the car-
navigation unit fixed in place install the bolt.

End Of Sie

LCD UNIT REMOVAL/INSTALLATION

A6E812466902W02

1. Disconnect the negative battery cable.
2. Remove the center panel module. (See

T–96 CENTER PANEL MODULE REMOVAL/INSTALLATION

.)

3. Remove in the order indicated in the table.

4. Install in the reverse order of removal.

LCD Unit Removal Note

1. Pull up the front part of the LCD unit.

1

Bolt

2

Car-navigation unit
(See

T–98 Car-navigation Unit Installation Note

)

3

Connector

A6E8124W015

A6E8124W016

1

Cover

2

Bolt

3

Screw

4

LCD unit
(See

T–98 LCD Unit Removal Note

)

5

Connector

A6E8124W014

A6E8124W017