Great Wall Hover. Manual — part 41
Front axle propeller shaft (4WD) assembly
Rear axle propeller shaft (4WD) assembly
N
m: Specified torque
universal-joint fork
front section of
rear axle propeller
shaft
intermediate sup-
port assembly
universal-
joint fork
shim
nut
circlip
cross-axle assembly
rear section assembly of
rear axle propeller shaft
flange fork
circlip
cross-axle assembly
axle tube assembly
front axle drive shaft assembly
N
m: Specified torque
universal-joint fork
circlip
cross-axle
assembly
drive shaft axle
pipe assembly
N
m: Specified torque
flange fork
transmission
drive shaft assembly
rear axle assembly
front axle drive shaft assembly
transmission
rear axle drive
shaft assembly
transfer case
rear axle assembly
Disassembly of drive shaft:
Remove the intermediate support bolt of drive shaft firstly (CC6460KY
is without intermediate support connecting bolt ), then remove the
connecting bolt between the drive shaft and rear axle , lastly, pull out
the drive shaft assembly from the transmission output spline shaft and
remove it in integral.
Installation of drive shaft:
1
. Firstly, check the drive shaft for damage, spline for corrosion
and connecting surface for deficiency of damage or sand hole by
itself.
2
Install the connecting spline bushing of drive shaft on the
transmission output spline shaft carefully; then install the drive
shaft intermediate support on the intermediate support bracket
of carriage.
3
. Use the special drive shaft bolt, nut and spring shim to connect
the drive shaft to the vehicle axle ring flange and tighten it. The
tightening torque is 78
5N
m
4
. Tighten the drive shaft intermediate support nut, the tightening
torque is 63
5N
m (the front and rear drive shaft in
CC6460KY model are the integral and has the installation
content)
Chapter 7
Suspension and vehicle axle
Rear suspension . . . . . . …112
Troubleshooting
Failure Cause
Repair
content
Floating/pulling
The tyre is worn or charged improperly.
The front wheel alignment is incorrect.
The wheel bearing is adjusted too tightened.
The front /rear suspension components is loose or
damaged
The steering linkage is loose or worn
The steering device is connected unsound or worn.
Charge the tyre to the proper pressure or
replace the tyre.
Check the condition of front wheel
alignment.
Adjust the wheel bearing
Tighten or replace the suspension
partTighten or replace the steering
linkage
Adjust or replace the steering device
Subsidence of vehicle body
Overload of vehicle
vibration damper is worn
spring is weak
Check the load weight
Replace the vibration damper
Replace the spring
Left-right swing/up-down
bounce
The tyre is charged improperly
The stabilizer bar is bend or damaged
The vibration damper is worn
Charge the tyre to the proper pressure
Replace the stabilizer bar
Replace the vibration damper
Front wheel vibration
The tyre is worn or is charged improperly
Unbalance of each wheel
The vibration damper is worn
The front wheel alignment is incorrect
The wheel bearing is worn or adjusted badly
The ball joint or bushing is worn
The steering system is loose or worn
The steering mechanism is adjusted badly or damaged
Replace the tyre or charge it to the proper
pressure.
Balance all wheels
Replace the vibration damper
Check the condition of front wheel
alignment
Replace or adjust the wheel bearing
Check the ball joint or bushing
Tighten or replace the steering linkage
Adjust or repair the steering device
Abnormal abrasion of tyre
The tyre is charged improperly
The vibration damper is worn
The front wheel alignment is badly
The suspension part is worn
Charge the tyre to the proper pressure
Replace the vibration damper
Check the condition of front wheel
alignment
Replace the suspension part
Oil leakage of differential
High oil level or incorrect oil grade
The oil seal is worn or damaged
The matching flange is loose or damaged
Drain the oil to the specified level or
replace the oil
Replace the oil seal
Tighten or replace the flange
The axle has the noise
The oil grade is low or incorrect
The clearance of the pinion, ring gear or side gear is
large.
The ring, pinion gear or side gear is worn or broken
The pinion gear bearing is worn
The bearing of rear axle half shaft is worn.
The differential bearing is loose or worn
Fill with the lubrication oil or replace the
oil according to the specification
Check the clearance
Check each gear
Replace the bearing
Replace the bearing
Tighten or replace the bearing
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст