Defender. Manual — part 118
power
Fuel injection
pump fault
Fuel rail
pressure
limiting valve
Clear the DTCs and carry out a road test to confirm repair.
P00897A Fuel pressure
regulator
performance
Fuel rail
pressure
limiting valve
has activated
The fuel rail pressure limiting valve operates as a disposable item
in the event of excess system pressure. Once activated the valve
cannot be guaranteed leak free and should be replaced. Install a
new fuel rail pressure limiting valve.
REFER to:
Fuel Pressure Relief Valve
(303-04A Fuel Charging and
Controls - 2.4L Duratorq-TDCi HPCR (103kW/140PS) - Puma,
Removal and Installation).
P009111 Fuel pressure
regulator control
circuit - circuit short
to ground
Fuel suction
control valve
circuit: short
circuit to
ground
Fuel suction
control valve
fault
Check the fuel suction control valve and circuits. Refer to the
electrical guides. The fuel suction control valve is not serviceable
separately. Install a new fuel injection pump if necessary.
REFER to:
Fuel Injection Pump
(303-04A Fuel Charging and
Controls - 2.4L Duratorq-TDCi HPCR (103kW/140PS) - Puma,
Removal and Installation).
Clear the DTCs and test for normal operation.
P009112 Fuel pressure
regulator control
circuit - circuit short
to battery
Fuel suction
control valve
circuit: short
circuit to power
Fuel suction
control valve
fault
P009211 Fuel pressure
regulator control
circuit - circuit short
to ground
Fuel suction
control valve
circuit: short
circuit to
ground
Fuel suction
control valve
fault
Check the fuel suction control valve and circuits. Refer to the
electrical guides. The fuel suction control valve is not serviceable
separately. Install a new fuel injection pump if necessary.
REFER to:
Fuel Injection Pump
(303-04A Fuel Charging and
Controls - 2.4L Duratorq-TDCi HPCR (103kW/140PS) - Puma,
Removal and Installation).
Clear the DTCs and test for normal operation.
P009212 Fuel pressure
regulator control
circuit - circuit short
to battery
Fuel suction
control valve
circuit: short
circuit to power
Fuel suction
control valve
fault
P01802F Fuel temperature
sensor A circuit -
signal erratic
Fuel
temperature
sensor circuit:
short circuit to
ground
Fuel
temperature
sensor circuit:
short circuit to
power
Fuel
temperature
sensor circuit:
open circuit
Fuel
temperature
sensor fault
Check the fuel temperature sensor and circuits. Refer to the
electrical guides. The fuel temperature sensor is not serviceable
separately. Install a new fuel injection pump if necessary.
REFER to:
Fuel Injection Pump
(303-04A Fuel Charging and
Controls - 2.4L Duratorq-TDCi HPCR (103kW/140PS) - Puma,
Removal and Installation).
Clear the DTCs and test for normal operation.
P018011 Fuel temperature
sensor A circuit -
circuit short to
ground
Fuel
temperature
sensor circuit:
short circuit to
ground
Fuel
temperature
sensor fault
P018015 Fuel temperature
Fuel
sensor A circuit -
circuit short to
battery or open
temperature
sensor circuit:
short circuit to
power
Fuel
temperature
sensor circuit:
open circuit
Fuel
temperature
sensor fault
P019011 Fuel rail pressure
sensor A circuit -
circuit short to
ground
Fuel rail
pressure sensor
circuit: short
circuit to
ground
Fuel rail
pressure sensor
fault
Check the fuel rail pressure sensor and circuits. Refer to the
electrical guides. The fuel rail pressure sensor is not serviceable
separately. Install a new fuel rail if necessary.
REFER to:
Fuel Rail
(303-04A Fuel Charging and Controls - 2.4L
Duratorq-TDCi HPCR (103kW/140PS) - Puma, Removal and
Installation).
Clear the DTCs and test for normal operation.
P019015 Fuel rail pressure
sensor A circuit -
circuit short to
battery or open
Fuel rail
pressure sensor
circuit: short
circuit to power
Fuel rail
pressure sensor
circuit: open
circuit
Fuel rail
pressure sensor
fault
P019164 Fuel rail pressure
sensor A circuit
range/performance -
signal plausibility
failure
Fuel rail
pressure sensor
circuit: short
circuit to power
Fuel rail
pressure sensor
circuit: short
circuit to
ground
Fuel rail
pressure sensor
circuit: open
circuit
Fuel rail
pressure sensor
fault
Check the fuel rail pressure sensor and circuits. Refer to the
electrical guides. The fuel rail pressure sensor is not serviceable
separately. Install a new fuel rail if necessary.
REFER to:
Fuel Rail
(303-04A Fuel Charging and Controls - 2.4L
Duratorq-TDCi HPCR (103kW/140PS) - Puma, Removal and
Installation).
Clear the DTCs and test for normal operation.
P020011 Injector circuit -
circuit short to
ground
Injector circuit:
short circuit to
ground
Injector fault
Check the injector and injector circuit. Refer to the electrical
guides. Install a new injector if necessary.
REFER to:
Fuel Injector
(303-04A Fuel Charging and Controls -
2.4L Duratorq-TDCi HPCR (103kW/140PS) - Puma, Removal and
Installation).
Clear the DTCs and test for normal operation.
P020012 Injector circuit -
circuit short to
battery
Injector circuit:
short circuit to
power
Injector fault
P020100 Cylinder 1 (injector
1) circuit / open
Cylinder 1
injector circuit:
open circuit
Cylinder 1
injector fault
Check the cylinder 1 injector and circuit. Refer to the electrical
guides. Install a new injector if necessary.
REFER to:
Fuel Injector
(303-04A Fuel Charging and Controls -
2.4L Duratorq-TDCi HPCR (103kW/140PS) - Puma, Removal and
Installation).
Clear the DTCs and test for normal operation.
P020200 Cylinder 2 (injector
4) circuit / open
Cylinder 2
injector circuit:
open circuit
Cylinder 2
injector fault
Check the cylinder 2 injector and circuit. Refer to the electrical
guides. Install a new injector if necessary.
REFER to:
Fuel Injector
(303-04A Fuel Charging and Controls -
2.4L Duratorq-TDCi HPCR (103kW/140PS) - Puma, Removal and
Installation).
Clear the DTCs and test for normal operation.
P020300 Cylinder 3 (injector
2) circuit / open
Cylinder 3
injector circuit:
open circuit
Check the cylinder 3 injector and circuit. Refer to the electrical
guides. Install a new injector if necessary.
REFER to:
Fuel Injector
(303-04A Fuel Charging and Controls -
Cylinder 3
injector fault
2.4L Duratorq-TDCi HPCR (103kW/140PS) - Puma, Removal and
Installation).
Clear the DTCs and test for normal operation.
P020400 Cylinder 4 (injector
3) circuit / open
Cylinder 4
injector circuit:
open circuit
Cylinder 4
injector fault
Check the cylinder 4 injector and circuit. Refer to the electrical
guides. Install a new injector if necessary.
REFER to:
Fuel Injector
(303-04A Fuel Charging and Controls -
2.4L Duratorq-TDCi HPCR (103kW/140PS) - Puma, Removal and
Installation).
Clear the DTCs and test for normal operation.
P026100 Cylinder 1 injector 1
circuit low
Cylinder 1
injector circuit:
short circuit to
ground
Cylinder 1
injector fault
Check the cylinder 1 injector and circuit. Refer to the electrical
guides. Install a new injector if necessary.
REFER to:
Fuel Injector
(303-04A Fuel Charging and Controls -
2.4L Duratorq-TDCi HPCR (103kW/140PS) - Puma, Removal and
Installation).
Clear the DTCs and test for normal operation.
P026400 Cylinder 2 injector 4
circuit low
Cylinder 2
injector circuit:
short circuit to
ground
Cylinder 2
injector fault
Check the cylinder 2 injector and circuit. Refer to the electrical
guides. Install a new injector if necessary.
REFER to:
Fuel Injector
(303-04A Fuel Charging and Controls -
2.4L Duratorq-TDCi HPCR (103kW/140PS) - Puma, Removal and
Installation).
Clear the DTCs and test for normal operation.
P026700 Cylinder 3 injector 2
circuit low
Cylinder 3
injector circuit:
short circuit to
ground
Cylinder 3
injector fault
Check the cylinder 3 injector and circuit. Refer to the electrical
guides. Install a new injector if necessary.
REFER to:
Fuel Injector
(303-04A Fuel Charging and Controls -
2.4L Duratorq-TDCi HPCR (103kW/140PS) - Puma, Removal and
Installation).
Clear the DTCs and test for normal operation.
P027000 Cylinder 4 injector 3
circuit low
Cylinder 4
injector circuit:
short circuit to
ground
Cylinder 4
injector fault
Check the cylinder 4 injector and circuit. Refer to the electrical
guides. Install a new injector if necessary.
REFER to:
Fuel Injector
(303-04A Fuel Charging and Controls -
2.4L Duratorq-TDCi HPCR (103kW/140PS) - Puma, Removal and
Installation).
Clear the DTCs and test for normal operation.
P029C00 Cylinder 1 balance -
(injector 1)
restricted
Injector leak
Cylinder
compression
low
- Blow-by
past the
injector
- Blow-by
past the
glow plug
- Mechanical
fault, valve,
piston/ring,
etc.
Injector fault
Check the injector and surrounding area for evidence of fuel
leakage. Disconnect the injector and check for evidence of fuel
leakage in the connector. Rectify as necessary. Clear the DTCs.
Reconnect the injector and start the engine. Allow to warm up
and allow to idle (cylinder balance diagnosis is now active). If the
DTC resets, check for blow-by etc. and rectify as necessary. Clear
the DTCs and recheck. Carry out a compression test only if the
DTC resets. If the above tests are all within range, install a new
injector.
REFER to:
Fuel Injector
(303-04A Fuel Charging and Controls -
2.4L Duratorq-TDCi HPCR (103kW/140PS) - Puma, Removal and
Installation).
Clear the DTCs and test for normal operation.
P02A000 Cylinder 2 balance -
(injector 4)
restricted
Injector leak
Cylinder
compression
low
- Blow-by
past the
injector
- Blow-by
past the
glow plug
- Mechanical
fault, valve,
piston/ring,
etc.
Injector fault
Check the injector and surrounding area for evidence of fuel
leakage. Disconnect the injector and check for evidence of fuel
leakage in the connector. Rectify as necessary. Clear the DTCs.
Reconnect the injector and start the engine. Allow to warm up
and allow to idle (cylinder balance diagnosis is now active). If the
DTC resets, check for blow-by etc. and rectify as necessary. Clear
the DTCs and recheck. Carry out a compression test only if the
DTC resets. If the above tests are all within range, install a new
injector.
REFER to:
Fuel Injector
(303-04A Fuel Charging and Controls -
2.4L Duratorq-TDCi HPCR (103kW/140PS) - Puma, Removal and
Installation).
Clear the DTCs and test for normal operation.
P02A400 Cylinder 3 balance -
(injector 2)
restricted
Injector leak
Cylinder
compression
low
- Blow-by
past the
injector
Check the injector and surrounding area for evidence of fuel
leakage. Disconnect the injector and check for evidence of fuel
leakage in the connector. Rectify as necessary. Clear the DTCs.
Reconnect the injector and start the engine. Allow to warm up
and allow to idle (cylinder balance diagnosis is now active). If the
injector
- Blow-by
past the
glow plug
- Mechanical
fault, valve,
piston/ring,
etc.
Injector fault
DTC resets, check for blow-by etc. and rectify as necessary. Clear
the DTCs and recheck. Carry out a compression test only if the
DTC resets. If the above tests are all within range, install a new
injector.
REFER to:
Fuel Injector
(303-04A Fuel Charging and Controls -
2.4L Duratorq-TDCi HPCR (103kW/140PS) - Puma, Removal and
Installation).
Clear the DTCs and test for normal operation.
P02A800 Cylinder 4 balance -
(injector 3)
restricted
Injector leak
Cylinder
compression
low
- Blow-by
past the
injector
- Blow-by
past the
glow plug
- Mechanical
fault, valve,
piston/ring,
etc.
Injector fault
Check the injector and surrounding area for evidence of fuel
leakage. Disconnect the injector and check for evidence of fuel
leakage in the connector. Rectify as necessary. Clear the DTCs.
Reconnect the injector and start the engine. Allow to warm up
and allow to idle (cylinder balance diagnosis is now active). If the
DTC resets, check for blow-by etc. and rectify as necessary. Clear
the DTCs and recheck. Carry out a compression test only if the
DTC resets. If the above tests are all within range, install a new
injector.
REFER to:
Fuel Injector
(303-04A Fuel Charging and Controls -
2.4L Duratorq-TDCi HPCR (103kW/140PS) - Puma, Removal and
Installation).
Clear the DTCs and test for normal operation.
P062B16 Internal control
module fuel injector
control performance
- circuit voltage
below threshold
Engine control
module (ECM)
fault
Refer to the warranty and policy and procedures manual if the
ECM is suspect.
P062B17 Internal control
module fuel injector
control performance
- circuit voltage
above threshold
Engine control
module (ECM)
fault
P115A00 Low fuel level -
forced limited power
Low fuel
Fuel level
sensor circuit:
short circuit to
ground
Fuel level
sensor circuit:
open circuit
Fuel level
sensor fault
Check that there is sufficient fuel in the tank. Check the fuel level
sensor and circuits. Refer to the electrical guides. Install a new
fuel level sensor if necessary.
REFER to:
Fuel Level Sender
(310-01 Fuel Tank and Lines - 2.4L
Duratorq-TDCi HPCR (103kW/140PS) - Puma, Removal and
Installation).
Clear the DTCs and test for normal operation.
P115B00 Low fuel level -
forced engine
shutdown
Low fuel
Fuel level
sensor circuit:
short circuit to
ground
Fuel level
sensor circuit:
open circuit
Fuel level
sensor fault
Check that there is sufficient fuel in the tank. Check the fuel level
sensor and circuits. Refer to the electrical guides. Install a new
fuel level sensor if necessary.
REFER to:
Fuel Level Sender
(310-01 Fuel Tank and Lines - 2.4L
Duratorq-TDCi HPCR (103kW/140PS) - Puma, Removal and
Installation).
Clear the DTCs and test for normal operation.
P116900 Fuel rail pressure
sensor in range but
high
Fuel rail
pressure sensor
circuit: short
circuit to
ground
Fuel rail
pressure sensor
circuit: short
circuit to power
Fuel rail
pressure sensor
circuit: open
circuit
Fuel rail
pressure sensor
fault
Check the fuel rail pressure sensor and circuits. Refer to the
electrical guides. The fuel rail pressure sensor is not serviceable
separately. Install a new fuel rail if necessary.
REFER to:
Fuel Rail
(303-04A Fuel Charging and Controls - 2.4L
Duratorq-TDCi HPCR (103kW/140PS) - Puma, Removal and
Installation).
Clear the DTCs and test for normal operation.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст