Discovery 2. Manual — part 441
ENGINE - V8
OVERHAUL 12-2-57
6. Apply smear of Retinax LX grease to oil seal
running surface on crankshaft.
7. Fit seal to timing gear cover using tool LRT-12-
089.
8. Clean and fit crankshaft pulley.
9. Fit crankshaft pulley bolt and tighten to 270 Nm
(200 lbf.ft).
10. Remove tool LRT-12-080 from crankshaft
pulley.
11. Clean oil filter mating face.
12. Lubricate new oil filter seal with clean engine oil
and fit filter.
13. Ensure coolant pump and pulley mating faces
are clean.
14. Remove all traces of thread locking material
from coolant pump pulley drive flange bolt
holes using an M8 tap.
15. Fit coolant pump pulley and tighten new
Patchlok bolts to 22 Nm (16 lbf.ft).
16. Fit oil pick up strainer.
ENGINE - V8, OVERHAUL, Strainer
Timing chain and gears
$% 12.65.12.01
Disassembly
1. Remove timing gear cover gasket.
ENGINE - V8, OVERHAUL, Gasket -
2. Fit crankshaft pulley bolt and rotate engine to
align timing marks. Remove crankshaft pulley
bolt.
ENGINE - V8
12-2-58 OVERHAUL
3. Restrain camshaft gear and remove gear
retaining bolt.
4. Remove timing chain and gears as an
assembly.
5. Remove gears from timing chain.
6. Remove key from crankshaft.
Reassembly
1. Clean timing chain and gears and gear
locations.
2. Fit key to crankshaft.
3. Temporarily fit gears to camshaft and
crankshaft. If necessary, rotate shafts to align
timing marks. When aligned correctly, the
timing marks will face each other; crankshaft
gear timing mark at twelve o'clock position and
camshaft gear timing mark at six o'clock
position.
4. Remove gears from shafts and fit to timing
chain.
5. With timing marks aligned, fit timing chain and
gears as an assembly.
6. Restrain the camshaft gear and tighten
retaining bolt to 50 Nm (37 lbf.ft).
7. Fit timing gear cover gasket.
ENGINE - V8
OVERHAUL 12-2-59
Rocker shaft - overhaul
$% 12.29.49
If both rocker shafts are to be removed, identify
each assembly to ensure refitment to original
cylinder head.
Disassembly
1. Release ht leads from rocker covers.
2. Remove 4 bolts securing rocker cover and
remove cover.
3. Remove and discard rocker cover gaskets.
4. Progressively remove 4 bolts securing rocker
shaft assembly to cylinder head, release
rocker shaft from push rods and remove rocker
shaft.
5. Ensure push rods remain located in tappets
when rocker shaft is removed. Retain all
components in their removed sequence for
re-assembly.
6. Remove and discard split pin from one end of
rocker shaft.
7. Collect plain and wave washers.
8. Remove the rocker arms, rocker pillars and
springs.
9. Remove and discard remaining split pin and
collect plain and wave washers.
Inspect
1. Clean all components.
2. Inspect rocker shaft and rocker arms for wear
and scoring. Replace as required.
3. Replace weak or broken springs.
4. Lubricate moving parts with clean engine oil.
ENGINE - V8
12-2-60 OVERHAUL
Reassembly
1. Reassemble rocker shafts, ensuring that
components are returned to their original
positions, secure plain washers with new split
pins.
2. Ensure shaft identification groove is positioned
at one o'clock, with push rod locations of rocker
arms to the right. Oil feed restriction will
result if rocker shafts are incorrectly
assembled.
3. Position rocker shaft assembly to cylinder
head ensuring push rods are engaged in
rocker arms.
4. Fit rocker shaft bolts and progressively tighten
to 40 Nm (30 lbf.ft).
5. Clean mating faces of rocker covers and
cylinder heads.
6. Fit new rocker cover gaskets, dry, position
rocker cover, fit bolts and working in diagonal
sequence, tighten to:
l
Stage 1 - 3 Nm (2.5 lbf.ft)
l
Stage 2 - 8 Nm (6 lbf.ft)
7. Ensure that gasket is correctly positioned
around periphery of rocker cover.
8. Secure ht leads to rocker cover.
Gasket - cylinder head
$% 12.29.02.01
Disassembly
1. Remove inlet manifold gasket.
ENGINE - V8, OVERHAUL, Gasket -
2. RH cylinder head: Remove auxiliary drive belt
tensioner.
3. RH cylinder head: Remove bolts securing
alternator mounting bracket and remove
bracket.
4. Noting their fitted order, disconnect ht leads
from spark plugs.
5. Progressively remove 4 bolts securing the
rocker shaft and remove rocker shaft.
6. Remove push rods and store in their fitted
order.
7. Working in the sequence shown remove 10
bolts securing the cylinder head to block.
Discard the bolts.
8. Remove cylinder head.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст