Discovery 2. Manual — part 729
CHARGING AND STARTING
REPAIRS
86-1-3
5. Remove alternator from mounting bracket.
6. Remove pulley from alternator.
Refit
1. Fit alternator pulley and tighten nut to 80 Nm
(59 lbf.ft).
2. Position alternator to mounting bracket.
3. Connect alternator cables and tighten B+ nut to
18 Nm (13 lbf.ft), and D+ nut to 5 Nm (3.7 lbf.ft).
4. Locate alternator in mounting bracket.
5. Fit alternator mounting bolts and tighten to 45
Nm (33 lbf.ft).
6. Fit auxiliary drive belt.
REPAIRS, Belt - auxiliary drive.
Belt - auxiliary drive
$% 86.10.03
Remove
1. Remove viscous fan:
l
l
2. Turn drive belt tensioner using a 15 mm ring
spanner and release belt from pulleys.
Refit
1. Clean drive belt pulley grooves and ensure
grooves are not damaged.
2. Fit new drive belt around pulleys, ensure belt is
correctly aligned in pulley grooves.
3. With assistance, hold tensioner fully clockwise
and fit drive belt around remaining pulley.
Release tensioner.
4. Fit viscous fan:
l
l
CHARGING AND STARTING
86-1-4
REPAIRS
Battery
$% 86.15.01
Remove
1. Release fixings and remove battery cover.
2. Disconnect both battery leads, negative lead
first.
3. Remove lock nuts and retaining nuts securing
battery clamp.
4. Remove battery clamp.
5. Remove battery.
Refit
1. Clean battery terminals and coat with
petroleum jelly.
2. Fit battery.
3. Fit battery clamp and tighten retaining nuts and
lock nuts.
4. Fit both battery leads, negative lead last.
5. Fit battery cover and secure fixings.
Battery carrier
$% 86.15.11
Remove
1. Remove battery.
2. Release strap and remove jack.
3. Release coolant hose from clip.
4. Diesel models: Remove screw securing ECM,
release ECM and position aside.
5. Remove 7 bolts securing battery carrier.
6. Remove battery carrier.
NOTE: Do not carry out further dismantling if
component is removed for access only.
7. Remove jack retaining strap, speed nut and
clip.
CHARGING AND STARTING
REPAIRS
86-1-5
Refit
1. Fit jack retaining strap, speed nut and clip.
2. Fit battery carrier, fit bolts and tighten to 28 Nm
(21 lbf.ft).
3. Diesel models: Fit ECM and secure with
screw.
4. Secure coolant hose.
5. Fit and secure jack.
6. Fit battery.
Starter motor - diesel
$% 86.60.01
Remove
1. Release fixings and remove battery cover.
2. Disconnect battery earth lead.
3. Raise front of vehicle.
WARNING: Do not work on or under a
vehicle supported only by a jack. Always
support the vehicle on safety stands.
4. Remove underbelly panel.
5. Disconnect Lucar connector from starter
solenoid.
6. Remove nut and disconnect battery lead from
starter solenoid.
7. Remove nut and 2 bolts securing starter motor
and remove starter motor from engine.
Refit
1. Clean starter motor and mating face on engine.
2. Fit starter motor and tighten nut and 2 bolts to
27 Nm (20 lbf.ft).
3. Connect lead to starter solenoid and tighten nut
to 10 Nm (7 lbf.ft).
4. Connect Lucar connector to starter solenoid.
5. Fit underbelly panel.
6. Remove stand(s) and lower vehicle.
7. Connect battery earth lead.
8. Fit battery cover and secure the fixings.
CHARGING AND STARTING
86-1-6
REPAIRS
Starter motor - V8
$% 86.60.01
Remove
1. Release fixings and remove battery cover.
2. Disconnect battery earth lead.
3. Raise front of vehicle.
WARNING: Do not work on or under a
vehicle supported only by a jack. Always
support the vehicle on safety stands.
4. Remove 3 nuts securing exhaust flange to
front pipe, release front pipe and collect
gasket.
5. Remove bolt securing heat shield to engine
mounting bracket, release heat shield from
starter motor and remove from vehicle.
6. Remove nut securing battery lead to starter
solenoid and release lead.
7. Disconnect Lucar connector from starter
solenoid.
8. Remove 2 Allen bolts securing starter motor
and remove starter motor from engine.
Refit
1. Clean starter motor and mating face on engine.
2. Fit starter motor and tighten Allen bolts to 44
Nm (32 lbf.ft).
3. Connect Lucar connector to starter solenoid.
4. Fit battery lead to solenoid and tighten nut.
5. Position heat shield to starter motor, locate tag
in engine mounting bracket, fit bolt and tighten
to 10 Nm (7 lbf.ft).
6. Clean exhaust manifold and front pipe mating
faces.
7. Using a new gasket, position front pipe, fit nuts
and tighten to 30 Nm (22 lbf.ft).
8. Remove stand(s) and lower vehicle.
9. Connect battery earth lead.
10. Fit battery cover and secure fixings.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст