Jaguar S-Type Electrical System Manual — part 11
The following abbreviations are used to represent values for Control Module Pin-Out data
I
Input
S
SCP Network
B+
Battery Voltage
Hz
Frequency
O
Output
A
ACP Network
V
Voltage (DC)
kHz
Frequency x 1000
REF
Reference Voltage / Ground
D
Serial and Encoded Data
PWM
Pulse Width Modulated
mA
Milliamperes
CAUTION: The information on this data page is furnished to aid the user in understanding circuit operation.
THIS INFORMATION SHOULD BE USED FOR
REFERENCE ONLY.
NOTE: The values listed are approximately those that can be expected at the control module connector pins with all circuit connections made and all components
connected and fitted.
“Active” means a load is applied or a switch is ON; “Inactive” means a load is not applied or a switch is OFF.
Refer to the front of this book for detailed information and illustrations regarding the location and identification of harnesses, relays, fuses, grounds, control
modules and control module pins.
DATE OF ISSUE:
July 1999
Fig. 08.1
COMPONENTS
Component
Connector(s)
Connector Description
Location
AUTOLAMP SENSOR
SL2
6-WAY / WHITE
TOP OF FASCIA
COLUMN SWITCHGEAR (LIGHTING STALK)
CS13
10-WAY / BLACK
STEERING COLUMN
FRONT POWER DISTRIBUTION BOX
ENGINE COMPARTMENT, RH FRONT
GENERAL ELECTRONIC CONTROL MODULE
CA24
26-WAY / WHITE
‘A’ POST, LH SIDE
CA31
20-WAY / BLACK
‘A’ POST, LH SIDE
CA84
4-WAY / GREY
‘A’ POST, LH SIDE
FH9
22-WAY / BLACK
‘A’ POST, LH SIDE
FH59
12-WAY / BLACK
‘A’ POST, LH SIDE
FH60
17-WAY / BLACK
‘A’ POST, LH SIDE
HEADLAMP UNIT – LH
HL2L
2-WAY / BLACK
ENGINE COMPARTMENT
HL3L
2-WAY / BLACK
ENGINE COMPARTMENT
HL4L
2-WAY / GREY
ENGINE COMPARTMENT
HL5L
10-WAY / BLACK
ENGINE COMPARTMENT
HEADLAMP UNIT – RH
HL2R
2-WAY / BLACK
ENGINE COMPARTMENT
HL3R
2-WAY / BLACK
ENGINE COMPARTMENT
HL4R
2-WAY / GREY
ENGINE COMPARTMENT
HL5R
10-WAY / BLACK
ENGINE COMPARTMENT
INSTRUMENT PACK
FC14
22-WAY / GREY
FASCIA
FC15
20-WAY / BLACK
FASCIA
FC63
22-WAY / BLACK
FASCIA
LIGHTING SWITCH
FC11
10-WAY / YELLOW
FASCIA, ADJACENT TO STEERING COLUMN
MESSAGE CENTER SWITCH PACK
FC65
8-WAY / BLACK
FASCIA, ADJACENT TO INSTRUMENT PACK
TURN SIGNAL REPEATER – LH
FH62
1-WAY / BLACK
FRONT FENDER, LH SIDE
TURN SIGNAL REPEATER – RH
FH76
1-WAY / BLACK
FRONT FENDER, RH SIDE
HARNESS IN-LINE CONNECTORS AND JUNCTION CONNECTORS
Connector
Connector Description
Location
BF1
6-WAY / GREY / FRONT HARNESS TO BUMPER LINK LEAD
BEHIND LH FRONT WHEEL ARCH LINER
CS3
10-WAY / GREY / FASCIA HARNESS TO COLUMN SWITCHGEAR HARNESS
BELOW STEERING COLUMN
FH39
12-WAY / GREY / FRONT HARNESS TO HEADLAMP LINK LEAD
BEHIND HEADLAMP ASSEMBLY, RH SIDE
FH40
12-WAY / GREY / FRONT HARNESS TO HEADLAMP LINK LEAD
BEHIND HEADLAMP ASSEMBLY, LH SIDE
SL3
10-WAY / GREY / FASCIA HARNESS TO ROAD PRICING MODULE LINK LEAD
BEHIND FASCIA END PANEL, RH SIDE
GROUNDS
Ground
Ground Description
Location
FC38
GROUND EYELET
BEHIND CENTER CONTROL CONSOLE / CENTER CONSOLE TRIM
FH22
GROUND EYELET
BEHIND LH HEADLAMP ASSEMBLY / ENGINE COMPARTMENT
FH77
GROUND EYELET
‘A’ POST; LH SIDE; ADJACENT TO GECM / ‘A’ POST TRIM
CONTROL MODULE PIN-OUT INFORMATION (FOLD OUT PAGE)
CONTROL MODULE PIN-OUT INFORMATION
General Electronic Control Module
P
Pin
Description
Active
Inactive
I
CA31-3
IGNITION SWITCHED POWER SUPPLY – LOGIC
B+
GROUND
O
FH9-7
LH TURN SIGNAL REPEATER ACTIVATE
GROUND (PULSED)
B+
O
FH9-11
RH SIDE MARKER ACTIVATE
GROUND
B+
O
FH9-19
RH TURN SIGNAL REPEATER ACTIVATE
GROUND (PULSED)
B+
O
FH9-22
LH SIDE MARKER ACTIVATE
GROUND
B+
S
FH59-1
SCP -
2 – 1600 Hz
O
FH59-2
LH FRONT PARK LAMP ACTIVATE
GROUND
B+
O
FH59-5
FRONT FOG LAMP RELAY ACTIVATE
GROUND
B+
I
FH59-6
BATTERY POWER SUPPLY
B+
B+
S
FH59-7
SCP +
2 – 1600 Hz
O
FH59-10
RH FRONT PARK LAMP ACTIVATE
GROUND
B+
I
FH59-12
GROUND SUPPLY
GROUND
GROUND
O
FH60-4
RH FRONT TURN SIGNAL LAMP ACTIVATE
GROUND (PULSED)
B+
O
FH60-5
LH FRONT TURN SIGNAL LAMP
GROUND (PULSED)
B+
O
FH60-7
RH DIPPED BEAM ACTIVATE
GROUND (PWM)
B+
O
FH60-8
LH DIPPED BEAM ACTIVATE
GROUND (PWM)
B+
O
FH60-10
RH MAIN BEAM ACTIVATE
GROUND (PWM)
B+
I
FH60-11
GROUND SUPPLY
GROUND
GROUND
I
FH60-13
GROUND SUPPLY
GROUND
GROUND
I
FH60-14
GROUND SUPPLY
GROUND
GROUND
I
FH60-15
GROUND SUPPLY
GROUND
GROUND
O
FH60-17
LH MAIN BEAM ACTIVATE
GROUND (PWM)
B+
Instrument Pack
P
Pin
Description
Active
Inactive
I
FC14-19
AUTO HEADLAMP SENSOR HEADLAMP ACTIVATION REQUEST
B+ = ON
GROUND = OFF
I
FC15-3
BATTERY POWER SUPPLY
B+
B+
I
FC15-6
IGNITION SWITCHED POWER SUPPLY
B+
GROUND
REF
FC15-9
LIGHTING STALK SWITCHES REFERENCE VOLTAGE
B+
GROUND
I
FC15-13
GROUND SUPPLY
GROUND
GROUND
S
FC15-15
SCP +
2 – 1600 Hz
S
FC15-16
SCP -
2 – 1600 Hz
I
FC15-17
IGNITION SWITCHED POWER SUPPLY
B+
GROUND
I
FC15-19
MAIN BEAM FLASH REQUEST
3.2V (MOMENTARY)
4.8V = AT REST
I
FC15-20
TURN SIGNALS / HAZARD LAMP ACTIVATE
GROUND = HAZARD; 1.2V = LEFT; 3.2V = RIGHT
4.7V = AT REST
REF
FC63-1
LIGHTING SWITCH REFERENCE GROUND
GROUND
GROUND
I
FC63-12
EXTERIOR LIGHTING MODE SELECTION REQUEST
2.9V = SIDE LAMPS; 2.1V = HEADLAMPS; 0.8V = FOGLAMPS
I
FC63-13
FRONT FOGLAMP ACTIVATION REQUEST
1.5V = ON
4.7V = OFF
I
FC63-14
AUTO HEADLAMP DELAY SETTING FEEDBACK
1.4V = 3 MINUTES
3.9V = SECONDS
NOTE: Refer to the Appendix at the rear of this book for SCP Network Messages.
The following abbreviations are used to represent values for Control Module Pin-Out data
I
Input
S
SCP Network
B+
Battery Voltage
Hz
Frequency
O
Output
A
ACP Network
V
Voltage (DC)
kHz
Frequency x 1000
REF
Reference Voltage / Ground
D
Serial and Encoded Data
PWM
Pulse Width Modulated
mA
Milliamperes
CAUTION: The information on this data page is furnished to aid the user in understanding circuit operation.
THIS INFORMATION SHOULD BE USED FOR
REFERENCE ONLY.
NOTE: The values listed are approximately those that can be expected at the control module connector pins with all circuit connections made and all components
connected and fitted.
“Active” means a load is applied or a switch is ON; “Inactive” means a load is not applied or a switch is OFF.
Refer to the front of this book for detailed information and illustrations regarding the location and identification of harnesses, relays, fuses, grounds, control
modules and control module pins.
DATE OF ISSUE:
July 1999
Fig. 08.2
COMPONENTS
Component
Connector(s)
Connector Description
Location
AUTOLAMP SENSOR
SL2
6-WAY / WHITE
TOP OF FASCIA
BRAKE SWITCH
CA37
2-WAY / GREEN
TOP OF BRAKE PEDAL
COLUMN SWITCHGEAR (LIGHTING STALK)
CS13
10-WAY / BLACK
STEERING COLUMN
HIGH MOUNTED STOP LAMP
CA18
3-WAY / GREY
PARCEL SHELF
INSTRUMENT PACK
FC14
22-WAY / GREY
FASCIA
FC15
20-WAY / BLACK
FASCIA
FC63
22-WAY / BLACK
FASCIA
LIGHTING SWITCH
FC11
10-WAY / YELLOW
FASCIA, ADJACENT TO STEERING COLUMN
MESSAGE CENTER SWITCH PACK
FC65
8-WAY / BLACK
FASCIA, ADJACENT TO INSTRUMENT PACK
NUMBER PLATE LAMP – LH
CA66
2-WAY / BLACK
BEHIND TRUNK LID LINER
NUMBER PLATE LAMP – RH
CA67
2-WAY / BLACK
BEHIND TRUNK LID LINER
POWERTRAIN CONTROL MODULE
FH1
58-WAY / GREY
FRONT BULKHEAD, PASSENGER SIDE
GB1
32-WAY / GREY
FRONT BULKHEAD, PASSENGER SIDE
PI1
60-WAY / GREY
FRONT BULKHEAD, PASSENGER SIDE
REAR ELECTRONIC CONTROL MODULE
CA63
17-WAY / BLACK
TRUNK, RH REAR
CA99
4-WAY / GREY
TRUNK, RH REAR
CA100
12-WAY / BLACK
TRUNK, RH REAR
CA101
20-WAY / BLACK
TRUNK, RH REAR
CA102
22-WAY / BLACK
TRUNK, RH REAR
CA103
26-WAY / WHITE
TRUNK, RH REAR
CA104
4-WAY / BLACK
TRUNK, RH REAR
SIDE MARKER LAMP – LH REAR
BR6
2-WAY / BLACK
REAR BUMPER, LH SIDE
SIDE MARKER LAMP – RH REAR
BR7
2-WAY / BLACK
REAR BUMPER, RH SIDE
TAIL LAMP UNIT – LH
CA10
7-WAY / BLACK
VEHICLE, LH REAR
TAIL LAMP UNIT – RH
CA68
7-WAY / BLACK
VEHICLE, RH REAR
HARNESS IN-LINE CONNECTORS AND JUNCTION CONNECTORS
Connector
Connector Description
Location
BR1
10-WAY / GREY / CABIN HARNESS TO BUMPER HARNESS
BEHIND RH REAR QUARTER TRIM
CA98
22-WAY / WHITE / JUNCTION CONNECTOR
TRUNK; ADJACENT TO RECM, RH SIDE
CA168
10-WAY / BLUE / DIODE MODULE
TRUNK, RH SIDE
CA169
2-WAY / BLACK / DIODE
BELOW RH REAR LAMP ASSEMBLY
CA170
2-WAY / BLACK / DIODE
BELOW LH REAR LAMP ASSEMBLY
CS3
10-WAY / GREY / FASCIA HARNESS TO COLUMN SWITCHGEAR HARNESS
BELOW STEERING COLUMN
FH13
20-WAY / BLACK / CABIN HARNESS TO FRONT HARNESS
ADJACENT TO PRIMARY JUNCTION BOX
SL3
10-WAY / GREY / FASCIA HARNESS TO ROAD PRICING MODULE LINK LEAD
BEHIND FASCIA END PANEL, RH SIDE
GROUNDS
Ground
Ground Description
Location
CA156
GROUND EYELET
TRUNK; RH REAR SIDE; ADJACENT TO RECM / TRUNK RH TRIM
FC38
GROUND EYELET
BEHIND CENTER CONTROL CONSOLE / CENTER CONSOLE TRIM
CONTROL MODULE PIN-OUT INFORMATION (FOLD OUT PAGE)
CONTROL MODULE PIN-OUT INFORMATION
Instrument Pack
P
Pin
Description
Active
Inactive
I
FC14-19
AUTO HEADLAMP SENSOR HEADLAMP ACTIVATION REQUEST
B+ = ON
GROUND = OFF
I
FC15-3
BATTERY POWER SUPPLY
B+
B+
I
FC15-6
IGNITION SWITCHED POWER SUPPLY
B+
GROUND
REF
FC15-9
LIGHTING STALK SWITCHES REFERENCE VOLTAGE
B+
GROUND
I
FC15-13
GROUND SUPPLY
GROUND
GROUND
S
FC15-15
SCP +
2 – 1600 Hz
S
FC15-16
SCP -
2 – 1600 Hz
I
FC15-17
IGNITION SWITCHED POWER SUPPLY
B+
GROUND
I
FC15-19
MAIN BEAM FLASH REQUEST
3.2V (MOMENTARY)
4.8V = AT REST
I
FC15-20
TURN SIGNALS / HAZARD LAMP ACTIVATE
GROUND = HAZARD; 1.2V = LEFT; 3.2V = RIGHT
4.7V = AT REST
REF
FC63-1
LIGHTING SWITCH REFERENCE GROUND
GROUND
GROUND
I
FC63-12
EXTERIOR LIGHTING MODE SELECTION REQUEST
2.9V = SIDE LAMPS; 2.1V = HEADLAMPS; 0.8V = FOGLAMPS
I
FC63-13
FRONT FOGLAMP ACTIVATION REQUEST
1.5V = ON
4.7V = OFF
I
FC63-14
AUTO HEADLAMP DELAY SETTING FEEDBACK
1.4V = 3 MINUTES
3.9V = SECONDS
Powertrain Control Module
P
Pin
Description
Active
Inactive
S
FH1-3
SCP +
2 – 1600 Hz
S
FH1-4
SCP -
2 – 1600 Hz
Rear Electronic Control Module
P
Pin
Description
Active
Inactive
O
CA63-1
RH STOP LAMP ACTIVATE
GROUND
B+
O
CA63-2
LH STOP LAMP ACTIVATE
GROUND
B+
O
CA63-3
LH REAR TURN SIGNAL ACTIVATE
GROUND (PULSED)
B+
O
CA63-4
RH REAR TURN SIGNAL ACTIVATE
GROUND (PULSED)
B+
O
CA63-5
RH TAIL LAMP ACTIVATE
GROUND
B+
O
CA63-6
LH TAIL LAMP ACTIVATE
GROUND
B+
O
CA63-7
LH REAR FOG LAMP ACTIVATE
GROUND
B+
O
CA63-8
RH REAR FOG LAMP ACTIVATE
GROUND
B+
O
CA63-9
LH REVERSE LAMP ACTIVATE
GROUND
B+
O
CA63-10
RH REVERSE LAMP ACTIVATE
GROUND
B+
O
CA63-17
HIGH MOUNTED STOP LAMP ACTIVATE
GROUND
B+
O
CA100-5
REAR NUMBER PLATE LAMP ACTIVATE
GROUND
B+
O
CA100-6
LH REAR SIDE MARKER LAMP ACTIVATE
GROUND
B+
I
CA100-8
IGNITION SWITCHED POWER SUPPLY – INERTIA SWITCH
B+
GROUND
O
CA100-12
RH REAR SIDE MARKER LAMP ACTIVATE
GROUND
B+
I
CA101-3
BATTERY POWER SUPPLY – LOGIC
B+
B+
S
CA102-1
SCP +
2 – 1600 Hz
S
CA102-2
SCP -
2 – 1600 Hz
I
CA102-12
GROUND
GROUND
GROUND
I
CA102-13
BRAKE ON / OFF SIGNAL
B+ = BRAKE APPLIED
GROUND
I
CA103-11
GROUND SUPPLY
GROUND
GROUND
I
CA103-12
GROUND SUPPLY
GROUND
GROUND
I
CA103-25
GROUND SUPPLY
GROUND
GROUND
I
CA103-26
GROUND SUPPLY
GROUND
GROUND
NOTE: Refer to the Appendix at the rear of this book for SCP Network Messages.
The following abbreviations are used to represent values for Control Module Pin-Out data
I
Input
S
SCP Network
B+
Battery Voltage
Hz
Frequency
O
Output
A
ACP Network
V
Voltage (DC)
kHz
Frequency x 1000
REF
Reference Voltage / Ground
D
Serial and Encoded Data
PWM
Pulse Width Modulated
mA
Milliamperes
CAUTION: The information on this data page is furnished to aid the user in understanding circuit operation.
THIS INFORMATION SHOULD BE USED FOR
REFERENCE ONLY.
NOTE: The values listed are approximately those that can be expected at the control module connector pins with all circuit connections made and all components
connected and fitted.
“Active” means a load is applied or a switch is ON; “Inactive” means a load is not applied or a switch is OFF.
Refer to the front of this book for detailed information and illustrations regarding the location and identification of harnesses, relays, fuses, grounds, control
modules and control module pins.
DATE OF ISSUE:
July 1999
Fig. 08.3
COMPONENTS
Component
Connector(s)
Connector Description
Location
BRAKE SWITCH
CA37
2-WAY / GREEN
TOP OF BRAKE PEDAL
HIGH MOUNTED STOP LAMP
CA18
3-WAY / GREY
PARCEL SHELF
NUMBER PLATE LAMP – LH
CA66
2-WAY / BLACK
BEHIND TRUNK LID LINER
NUMBER PLATE LAMP – RH
CA67
2-WAY / BLACK
BEHIND TRUNK LID LINER
REAR ELECTRONIC CONTROL MODULE
CA63
17-WAY / BLACK
TRUNK, RH REAR
CA99
4-WAY / GREY
TRUNK, RH REAR
CA100
12-WAY / BLACK
TRUNK, RH REAR
CA101
20-WAY / BLACK
TRUNK, RH REAR
CA102
22-WAY / BLACK
TRUNK, RH REAR
CA103
26-WAY / WHITE
TRUNK, RH REAR
CA104
4-WAY / BLACK
TRUNK, RH REAR
SIDE MARKER LAMP – LH REAR
BR6
2-WAY / BLACK
REAR BUMPER, LH SIDE
SIDE MARKER LAMP – RH REAR
BR7
2-WAY / BLACK
REAR BUMPER, RH SIDE
TAIL LAMP UNIT – LH
CA10
7-WAY / BLACK
VEHICLE, LH REAR
TAIL LAMP UNIT – RH
CA68
7-WAY / BLACK
VEHICLE, RH REAR
HARNESS IN-LINE CONNECTORS AND JUNCTION CONNECTORS
Connector
Connector Description
Location
BR1
10-WAY / GREY / CABIN HARNESS TO BUMPER HARNESS
BEHIND RH REAR QUARTER TRIM
CA98
22-WAY / WHITE / JUNCTION CONNECTOR
TRUNK; ADJACENT TO RECM, RH SIDE
CA168
10-WAY / BLUE / DIODE MODULE
TRUNK, RH SIDE
CA169
2-WAY / BLACK / DIODE
BELOW RH REAR LAMP ASSEMBLY
CA170
2-WAY / BLACK / DIODE
BELOW LH REAR LAMP ASSEMBLY
FH13
20-WAY / BLACK / CABIN HARNESS TO FRONT HARNESS
ADJACENT TO PRIMARY JUNCTION BOX
GROUNDS
Ground
Ground Description
Location
CA156
GROUND EYELET
TRUNK; RH REAR SIDE; ADJACENT TO RECM / TRUNK RH TRIM
CONTROL MODULE PIN-OUT INFORMATION (FOLD OUT PAGE)
CONTROL MODULE PIN-OUT INFORMATION
Rear Electronic Control Module
P
Pin
Description
Active
Inactive
O
CA100-5
REAR NUMBER PLATE LAMP ACTIVATE
GROUND
B+
O
CA100-6
LH REAR SIDE MARKER LAMP ACTIVATE
GROUND
B+
I
CA100-8
IGNITION SWITCHED POWER SUPPLY – INERTIA SWITCH
B+
GROUND
O
CA100-12
RH REAR SIDE MARKER LAMP ACTIVATE
GROUND
B+
I
CA101-3
BATTERY POWER SUPPLY – LOGIC
B+
B+
S
CA102-1
SCP +
2 – 1600 Hz
S
CA102-2
SCP -
2 – 1600 Hz
I
CA102-12
GROUND
GROUND
GROUND
I
CA102-13
BRAKE ON / OFF SIGNAL
B+ = BRAKE APPLIED
GROUND
I
CA103-11
GROUND SUPPLY
GROUND
GROUND
I
CA103-12
GROUND SUPPLY
GROUND
GROUND
I
CA103-25
GROUND SUPPLY
GROUND
GROUND
I
CA103-26
GROUND SUPPLY
GROUND
GROUND
NOTE: Refer to the Appendix at the rear of this book for SCP Network Messages.
Большое спасибо!
Ваше мнение очень важно для нас.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст