Ford Escape Hybrid (2012 year). Manual — part 24
MYKEY
姞
The MyKey
威 feature allows you to program a restricted driving mode to
promote good driving habits. All but one of the keys programmed to the
vehicle can be activated as a MyKey
威. The key will remain restricted
until MyKey
威 is cleared. Any remaining keys are referred to as an
“administrator key” or admin key. The admin key can be used to create a
MyKey
威, program optional MyKey威 settings, and clear the MyKey威
feature. When the MyKey
威 feature is enabled the user can use System
Check in the message center to see how many MyKeys
威 and admin keys
are programmed to the vehicle, and how many total miles have been
driven with the MyKey
威 active.
MyKey
威 restricted features
Standard settings – these settings cannot be changed
• The audio system will be muted whenever Belt-Minder威 is activated
until the safety belts are buckled. Refer to the Seating and Safety
Restraints chapter for a detailed description of Belt-Minder
威 operation.
• Low fuel warnings are displayed in the message center followed by a
chime when the distance to empty value reaches 75 miles (120 km).
• The reverse sensing system cannot be turned off.
Optional settings – these settings can be changed
• Vehicle speed is limited to 80 mph (130 km/h). Visual warnings are
displayed followed by a chime when the vehicle speed has reached
80 mph (130 km/h).
• Visual warnings are displayed followed by a chime when a preselected
vehicle speed of 45, 55 or 65 mph (75, 90, or 105 km/h) is exceeded.
• The maximum volume of the audio system is limited to 45%. MYKEY
VOLUME LIMITED will be displayed in the radio or (if equipped)
navigation screen when attempting to exceed the limited volume.
• The AdvanceTrac威 system cannot be turned off. When this optional
setting is on, the MyKey
威 user will not be able to deactivate the
system. Note: It may be beneficial to deactivate the AdvanceTrac
威
system if the vehicle is stuck in snow, mud, or sand.
Create a MyKey
威
To program MyKey
威 on one of the keys programmed to the vehicle,
insert the key that you want to make a MyKey
威 into the ignition. Turn
the ignition on. Use the message center buttons to do the following:
1. Press SETUP until PRESS RESET TO CREATE MYKEY is displayed.
Locks and Security
98
2. Press and release the RESET button. HOLD RESET TO CONFIRM
MYKEY will be displayed.
3. Press and hold the RESET button for two seconds until MARK THIS
AS RESTRICTED is displayed.
4. Wait until KEY RESTRICTED AT NEXT START is displayed.
MyKey
威 is successfully programmed. Make sure you label it so you can
distinguish it from the admin keys. Note: To program the optional
settings go to Step 2 in the Programming MyKey
威 Optional Settings
section. If your vehicle is equipped with remote start, see the Using
MyKey
威 with Remote Start Systems section.
Note: The MyKey
威 can be cleared within the same key cycle that it was
created, otherwise a standard key (Administrator key) is required to
clear the MyKey
威 programming. To clear all MyKeys威 go to Step 2 in the
Clear MyKey
威 section.
Programming MyKey
威 Optional Settings
Turn the ignition on using an admin key. To program the optional
settings, use the message center buttons to do the following:
1. Press SETUP until RESET FOR MYKEY SETTINGS is displayed.
2. Press and release the RESET button to display MyKey
威 setup menus.
The first menu shown is:
MYKEY MAX MPH <80 MPH> OFF
3. If you don’t want to change the maximum speed setting, press the
SETUP button to display the next menu. The remaining menus appear as
follows with the default settings shown:
MYKEY MPH TONES 45 55 65 <OFF>
MYKEY VOLUME LIMIT <ON> OFF
MYKEY ADVTRAC CTRL ON <OFF>.
4. On any of the menus press RESET to highlight your choice with the
<…>.
5. Press SETUP to enter your choice. The next optional setting will be
displayed.
6. Repeat Steps 4 and 5 until you are done changing the optional settings.
Clear MyKey
威
To reset all MyKeys
威 as admin keys do the following:
1. Turn the vehicle on using the admin key.
2. Press SETUP until PRESS RESET TO CLEAR MYKEY is displayed.
Locks and Security
99
3. Press and release the RESET button. HOLD RESET TO CONFIRM
CLEAR is displayed.
4. Press and hold the RESET button for two seconds until ALL MYKEYS
CLEARED is displayed.
Check MyKey
威 System Status
The vehicle’s message center system check will provide the status of the
following MyKey
威 parameters:
• MYKEY MILES — This odometer only tracks mileage when a MyKey威
is used. If mileage does not accumulate as expected, then the MyKey
威
is not being used by the intended user. The only way to reset this
odometer to zero is by clearing MyKey
威. If this odometer is lower than
the last time you checked, then the MyKey
威 system has been recently
cleared.
• # MYKEY(S) PROGRAMMED — Indicates how many MyKeys威 are
programmed to the vehicle. Can be used to detect deletion of a
MyKey
威.
• # ADMIN KEYS PROGRAMMED — Indicates how many Admin keys
are programmed to the vehicle. Can be used to detect if an additional
spare key has been programmed to the vehicle
Refer to Message center in the Instrument Cluster chapter for MyKey
威
system warnings displays.
Using MyKey
威 with Remote Start Systems
MyKey
威 is not compatible with non-Ford approved aftermarket remote
start systems. If you choose to install a remote start system please see
your authorized dealer for a Ford approved remote start system.
When using a Ford-approved remote start system, the default settings
will recognize the remote start system as an additional admin Key with
its associated privileges. You should program the remote start system as
a MyKey
威 in addition to the key that you have already programmed as a
MyKey
威. To program the remote start system as MyKey威, do the
following:
1. Enter the vehicle and close all doors.
2. Remote start the vehicle using a remote start fob.
3. Follow steps 1-4 in the Create a MyKey
威 section.
Note: For all vehicles, the number of MYKEY(S) PROGRAMMED or
ADMIN KEYS PROGRAMMED that is displayed in the MyKey
威 System
Status menus will include the remote start system as an additional key in
the total count. See the Check MyKey
威 System Status section.
Locks and Security
100
Note: For all vehicles with remote start installed, it is possible to
program all original vehicle keys as MyKeys
威, in which case, you will
need to use your remote start system to reset all MyKeys
威 as admin keys
by doing the following:
1. Enter the vehicle, close all doors.
2. Remote start the vehicle using your remote start fob.
3. Follow Steps 1-4 in the Clear MyKey
威 section.
Troubleshooting
Condition
Potential Causes
Can’t create a MyKey
威
• Key in the ignition is already a
MyKey
威
• Key in the ignition is the last
remaining admin key (there always
has to be at least one admin key)
• SecuriLock威 Passive Anti-Theft
System is disabled or in unlimited
mode
• Vehicle has been started using a
remote start system that is
programmed as MyKey
威. Refer to
Using MyKey
威 with Remote Start
Systems section.
Cannot program the MyKey
威
optional settings
• Key in the ignition is a MyKey威
• No MyKeys威 are programmed to the
vehicle. Refer to Create a MyKey
威
section
• Vehicle has been started using a
remote start system that is
programmed as MyKey
威. Refer to
Using MyKey
威 with Remote Start
Systems section.
Locks and Security
101
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст