Volvo S60 Inscription (2016 year). Instruction — part 9
||
07 Driver support
07
152
*
Option/accessory, for more information, see Introduction.
WARNING
•
Adaptive Cruise Control is not a colli-
sion avoidance system. The driver is
always responsible for applying the
brakes if the system does not detect
another vehicle.
•
Adaptive Cruise Control does not react
to people or animals, or small vehicles
such as bicycles and motorcycles. It
also does not react to slow moving,
parked or approaching vehicles, or
stationary objects.
•
Do not use Adaptive Cruise Control in
demanding driving conditions such as
city driving or other heavy traffic situa-
tions, in slippery conditions, when
there is a great deal of water or slush
on the road, during heavy rain or
snow, in poor visibility, on winding
roads or on highway on- or off-ramps.
The distance to the vehicle ahead (in the
same lane) is monitored by a radar sensor.
Your vehicle's speed is regulated by acceler-
ating and braking. The brakes may emit a
sound when they are being modulated by the
adaptive cruise control system. This is nor-
mal.
WARNING
The brake pedal moves when the adaptive
cruise control system modulates the
brakes. Do not rest your foot under the
brake pedal.
The ACC system is designed to smoothly
regulate speed. However, the driver must
apply the brakes in situations that require
immediate braking. This applies when there
are great differences in speed between vehi-
cles, or if the vehicle ahead brakes suddenly.
WARNING
Due to limitations in the radar sensor,
braking may occur unexpectedly or not at
all, see Adaptive Cruise Control – limita-
Adaptive Cruise Control can be put in active
mode at any permitted speed. However, if the
vehicle's speed falls below 18 mph (30 km/h)
or if engine speed (rpm) becomes too low,
ACC disengages (goes into standby mode)
and will no longer modulate the brakes. The
driver will then have to maintain a safe dis-
tance to the vehicle ahead.
WARNING
When Adaptive Cruise Control is in
standby mode or is switched off com-
pletely, the brakes will not be modulated
automatically. The driver must assume full
control over the vehicle.
Warning light—driver braking required
Adaptive Cruise Control can exert brake force
that is equivalent to approximately 40% of
the vehicle's total braking capacity. In situa-
tions requiring more brake force than ACC
can provide and if the driver does not apply
the brakes, an audible signal from the Colli-
sion Warning system will sound and warning
light will illuminate (see Collision warning* –
function (p. 177)) in the windshield to alert
the driver to react.
Strong sunlight, reflections, extreme light
contrasts, the use of sunglasses, or if the
driver is not looking straight ahead may
make the visual warning signal in the wind-
shield difficult to see.
1
The illustration is generic; details will vary, depending on the model
07 Driver support
07
153
WARNING
Adaptive Cruise Control only warns of
vehicles detected by the radar sensor, see
Adaptive Cruise Control – limitations
(p. 159). In some cases there may be no
warning or the warning may be delayed.
The driver should always apply the brakes
when necessary.
Steep inclines and/or heavy loads
ACC is primarily intended for use on fairly
level roads. The system may have difficulty
maintaining the correct distance to a vehicle
ahead on steep inclines, if the vehicle is car-
rying a heavy load or is towing a trailer. In
these situations, the driver should always be
prepared to apply the brakes if necessary.
Related information
•
Adaptive Cruise Control – introduction
Adaptive Cruise Control – engaging
Putting ACC in standby mode
Before ACC can be used to regulate speed
and/or the distance to a vehicle ahead, it
must first be put in standby mode.
To do so:
Controls and display
Off/On/Standby mode
•
Press
(2).
> The same symbol (7) appears (in white) in
the instrument panel to indicate that ACC
is in standby mode.
The driver's door must be closed and the
driver's seat belt must be fastened before
ACC can be put in active mode. If the driv-
er's seat belt is taken off or if the driver's
door is opened, ACC will return to standby
mode.
Related information
•
07 Driver support
07
154
Adaptive Cruise Control – setting
speed
Setting a speed
Once ACC has been put in standby mode:
Controls and display
Put in active mode and set a speed (each
additional press increases/decreases
speed by 1 mph (approximately 2 km/h))
•
Press
or
(4).
> The set speed, for example 60 mph (5),
will be magnified for several seconds and
the frame around the speed will change
colors from white to green to indicate
that this speed has been stored (set).
When this symbol has changed col-
ors from white to green, ACC is in
active mode and the vehicle will
maintain the set speed.
This symbol indicates that
you are approaching a vehi-
cle ahead.
ACC will switch from main-
taining a set speed to main-
taining a set distance from
that vehicle.
When this happens, a speed
range will be indicated on
the speedometer:
The higher speed (the cur-
rently set speed (5)) will be
marked in green.
The lower speed in the range is the speed of
the vehicle ahead.
Changing the set speed
•
After a speed has been set, it can be
increased or decreased by briefly press-
ing the
or
buttons. Each time one
of these buttons is pressed, the vehicle's
speed changes by 5 mph or 5 km/h. If the
speed is increased by pressing the accel-
erator pedal, the vehicle's speed when
the button is pressed will be set.
•
Press and hold one of these buttons to
increase/decrease the speed in 1-mph or
1-km/h increments. Release the button
when you have reached the desired
speed.
•
If one of the Adaptive Cruise Control
buttons is pressed for more than
approximately one minute, ACC will be
deactivated. The engine must then be
switched off and restarted to reset
ACC.
•
In some situations Adaptive Cruise
Control cannot be put in active mode.
Cruise control Unavailable
is shown
in the display, see Adaptive Cruise
Control – symbols and messages
Related information
•
07 Driver support
07
}}
155
Adaptive Cruise Control – setting time
interval
Setting a time interval
Controls and display
Decrease/increase time interval
The set time interval to vehicles ahead can be
increased by pressing
and decreased by
pressing
. The current time interval is
shown briefly in the display following adjust-
ment.
Different time intervals can
be selected and are shown in
the instrument panel
2
as 1–5
horizontal bars. The greater
the number of bars, the
longer the time interval. One
bar represents a time interval
of approximately 1 second; 5 bars is approxi-
mately 3 seconds.
To set/change a time interval:
•
Press the
/
buttons (3).
At low speeds, when the distance to the vehi-
cle ahead is short, ACC increases the time
interval slightly. In order to follow the vehicle
ahead as smoothly as possible, ACC allows
the time interval to vary considerably in cer-
tain situations.
WARNING
•
Only use a time interval that is suitable
in current traffic conditions.
•
A short time interval gives the driver
limited reaction time if an unexpected
situation occurs in traffic.
Related information
•
Adaptive Cruise Control – introduction
Adaptive Cruise Control –
deactivating
Standby mode (temporary deactivation)
To temporarily deactivate ACC (put it in
standby mode):
Controls and display
Resume previous settings.
Off/On/Standby mode
•
Press
(2).
This symbol and the marking for the set
speed with change colors from green to
white.
The previously set speed and time interval are
resumed by pressing
(1).
2
The same symbol appears if Distance Alert (see Distance Alert – introduction (p. 164)) is activated
||
07 Driver support
07
156
WARNING
The vehicle may accelerate quickly after
has been pressed if its current speed is
considerably lower than the set speed.
Standby mode due to action by the
driver
ACC is temporarily deactivated and put in
standby mode:
•
if the brakes are applied
•
if the gear selector is moved to N
•
if the driver drives faster than the set
speed for more than 1 minute.
In this happens, the driver will have to regu-
late the vehicle's speed.
If the accelerator pedal is only depressed
for a short time, such as when passing
another vehicle, ACC is deactivated tem-
porarily and is reactivated when the pedal
is released.
Automatic standby mode
ACC is linked to other systems such as the
stability system. If this system is not function-
ing properly, ACC will switch off automati-
cally.
In the event of automatic deactivation, an
audible signal will sound and the message
Cruise control Cancelled
is shown in the
instrument panel. The driver must then inter-
vene and adapt the vehicle's speed to the
surrounding traffic and regulate the distance
to the vehicle ahead.
An automatic switch to standby mode may be
caused if:
•
engine speed (rpm) is too high/low
•
The driver's door is opened
•
The driver unbuckles his/her seat belt
•
the vehicle's speed goes below 18 mph
(30 km/h)
•
the wheels lose traction
•
brake temperature is high
•
the radar sensor is obstructed by, for
example, wet snow or rain.
Resuming the set speed
If ACC is in standby mode, it can be reactiva-
ted by pressing the
button on the steering
wheel keypad. The vehicle will return to the
most recently set speed.
WARNING
The vehicle may accelerate quickly after
has been pressed if its current speed is
considerably lower than the set speed.
Turning ACC off completely
Controls and display
Resume previous settings.
Off/On/Standby mode
•
From standby mode, press (2)
once.
•
From active mode, press (2)
twice.
The set speed and time interval are then
cleared from the system's memory and can-
not be resumed by pressing (1)
.
Related information
•
07 Driver support
07
}}
157
Adaptive Cruise Control – passing
another vehicle
Passing another vehicle
If your vehicle’s speed is being regulated by
ACC and the driver indicates that he/she
would like to pass the vehicle ahead by using
the left turn signal, ACC can assist by accel-
erating briefly.
This function is active at speeds above
approximately 45 mph (70 km/h).
WARNING
Please be aware that this function will also
cause the vehicle to accelerate briefly in
certain situations other than passing
another vehicle, for example using the left
turn signal to indicate a lane change or a
turn toward a highway exit at speeds
above approximately 45 mph (70 km/h).
Related information
•
Adaptive Cruise Control – introduction
Adaptive Cruise Control (ACC) –
Queue Assist
Queue Assist is an added ACC feature that is
linked to your vehicle's automatic transmis-
sion.
Introduction
Queue Assist is an added ACC feature that is
linked to your vehicle's automatic transmis-
sion.
Queue Assist consists of the following func-
tions:
•
Enhanced speed interval (including when
the vehicle is at a complete stop or is
moving at speed below 18 mph
(30 km/h))
•
Automatic standby mode when ACC
changes target vehicles
•
No automatic braking when at a standstill
•
The parking brake is applied automati-
cally
Please note that the lowest speed that can be
set is 18 mph (30 km/h), although ACC can
maintain a set speed/distance to a vehicle
ahead down to a standstill. Queue Assist
consists of the following features:
Enhanced speed interval
The driver's door must be closed and the
driver's seat belt must be fastened before
ACC can be put in active mode. If the driv-
er's seat belt is taken off or if the driver's
door is opened, ACC will return to standby
mode.
Your vehicle can maintain the set time interval
to the vehicle ahead at any permissible
speed, including a complete stop.
In order to activate ACC at speeds below
18 mph (30 km/h):
•
The vehicle ahead must be within a rea-
sonable distance (not farther away than
approx. 100 ft/30 meters)
•
The lowest speed that can be selected is
18 mph (30 km/h), although ACC will also
help maintain the set time interval to the
vehicle ahead at lower speeds, including
a complete stop.
During short stops (less than approximately
3 seconds) in slow-moving traffic, your vehi-
cle will begin moving again automatically as
soon as the vehicle ahead begins to move.
If it takes more than 3 seconds for the vehicle
ahead to begin moving, ACC will be automat-
ically go into standby mode.
||
07 Driver support
07
158
The driver will then have to reactivate ACC in
one of the following ways:
•
By pressing
•
By accelerating up to at least 3 mph
(4 km/h). ACC will then resume following
the vehicle ahead.
Your vehicle will then resume following the
vehicle ahead at the set time interval.
ACC can remain active and keep your
vehicle at a standstill for up to 4 minutes.
After 4 minutes have elapsed, the parking
brake will be engaged and ACC will go into
standby mode.
To reactivate ACC, the driver must release
the parking brake (see Parking brake –
general information (p. 232)).
Automatic standby mode when ACC
changes target vehicles
If the vehicle ahead turns suddenly, there may be
a stationary vehicle ahead
The following only applies at speeds below
approximately 18 mph (30 km/h):
If ACC changes target vehicles (the vehicle
that the radar sensor has detected) from a
moving vehicle to a stationary one, the sys-
tem will apply the brakes in your vehicle.
WARNING
At speeds above 18 mph (30 km/h), ACC
will not react to a stationary vehicle and
apply the brakes but will instead acceler-
ate to the previously set speed. The driver
must actively apply the brakes to stop the
vehicle.
ACC disengages and goes into standby
mode if:
•
Your vehicle's speed goes below 10 mph
(15 km/h) and ACC cannot determine if
the target object is a stationary vehicle or
some other type of object such as e.g., a
speed bump.
•
Your vehicle's speed goes below 10 mph
(15 km/h) and the vehicle ahead turns so
that ACC no longer has a target vehicle to
follow.
No automatic braking when at a
standstill
In certain situations, ACC will no longer apply
the brakes and go into standby mode while
the vehicle is not moving. This means that the
driver will have to apply the brakes.
This happens if:
•
The driver presses the brake pedal
•
The parking brake is activated
•
The gear selected is moved to P, N or R
•
The driver presses the
button to put
ACC in standby mode
The parking brake is applied
automatically
In certain situations, ACC will apply the park-
ing brake in order to continue keeping the
vehicle at a standstill.
This happens if:
•
The driver opens the door or takes off
his/her seat belt
•
The stability system is put in Sport mode
(see Stability system – operation (p. 142))
•
ACC has kept the vehicle at a standstill
for more than 2 minutes
•
The engine has been switched off
•
The brakes have overheated
Related information
•
07 Driver support
07
}}
159
Radar sensor
The radar sensor is designed to help detect
cars or larger vehicles driving in the same
direction as your vehicle, in the same lane.
The radar sensor and its limitations
In addition to being used by the Adaptive
Cruise Control (ACC), the radar sensor is also
used by Distance Alert (see Distance Alert –
introduction (p. 164)) and Collision Warning
with Full Auto-brake and Pedestrian Detec-
tion (see Collision warning – introduction
WARNING
•
If there is visible damage to the front
grille or you suspect that the radar
sensor may be damaged in any way,
contact a trained and qualified Volvo
service technician as soon as possible.
The radar sensor may only function
partially (or not at all) if it is damaged
or is not securely fastened in place.
•
Accessories or other objects, such as
extra headlights, must not be installed
in front of the grille.
•
Modification of the radar sensor could
make its use illegal.
The radar sensor's capacity to detect vehi-
cles ahead is impeded:
•
if the radar sensor is obstructed and can-
not detect other vehicles, for example in
heavy rain, or if snow or other objects are
obscuring the radar sensor.
Keep the area in front of the radar sensor
clean.
•
if the speed of vehicles ahead is signifi-
cantly different from your own speed.
Related information
•
Adaptive Cruise Control – introduction
•
Collision warning – introduction (p. 175)
•
Distance Alert – introduction (p. 164)
Adaptive Cruise Control – limitations
The ACC cannot cover all driving situations
and traffic, weather and road conditions.
Situations where ACC may not function
optimally
WARNING
•
The radar sensor has a limited field of
vision. In some situations it may detect
a vehicle later than expected or not
detect other vehicles at all.
•
If ACC is not functioning properly,
cruise control will also be disabled.
||
07 Driver support
07
160
Radar sensor's field of vision (shown in pink)
In certain situations, the radar sensor
cannot detect vehicles at close quarters,
for example a vehicle that suddenly
enters the lane between your vehicle and
the target vehicle.
Small vehicles, such as motorcycles, or
vehicles not driving in the center of the
lane may remain undetected.
In curves, the radar sensor may detect
the wrong vehicle or lose sight of the tar-
get vehicle.
WARNING
•
Adaptive Cruise Control cannot cover
all driving situations and traffic,
weather and road conditions. The
"Function" section provides informa-
tion about limitations that the driver
must be aware of before using this
feature.
•
This system is designed to be a sup-
plementary driving aid. It is not, how-
ever, intended to replace the driver's
attention and judgement. The driver is
responsible for maintaining a safe dis-
tance and speed and must intervene if
Adaptive Cruise Control does not
maintain a suitable speed or suitable
distance to the vehicle ahead.
•
Maintenance of ACC components may
only be performed by a trained and
qualified Volvo technician.
WARNING
•
Adaptive Cruise Control is not a colli-
sion avoidance system. The driver is
always responsible for applying the
brakes if the system does not detect
another vehicle.
•
Adaptive Cruise Control does not react
to people or animals, or small vehicles
such as bicycles and motorcycles. It
also does not react to slow moving,
parked or approaching vehicles, or
stationary objects.
•
Do not use Adaptive Cruise Control in
demanding driving conditions such as
city driving or other heavy traffic situa-
tions, in slippery conditions, when
there is a great deal of water or slush
on the road, during heavy rain or
snow, in poor visibility, on winding
roads or on highway on- or off-ramps.
Related information
•
07 Driver support
07
}}
161
Adaptive Cruise Control – symbols
and messages
Symbols and messages in the display
A text message can be erased by pressing
briefly on the OK button on the turn signal
lever.
Symbol Message
Description
Green symbol
A speed has been set.
White symbol
ACC is in standby mode but no speed has been set.
-
Standard cruise control has been selected manually.
-
Set ESC to Normal to
enable Cruise
ACC cannot be put in active mode until the stability system is switched normal operating mode, see
Stability system – introduction (p. 141) for more information.
-
Cruise control Cancel-
led
ACC has been automatically switched off. The driver has to regulate the vehicle’s speed/distance to the
vehicle ahead.
-
Cruise control Unavail-
able
ACC cannot be put in active mode. This may be due to:
•
high brake temperature
•
the radar sensor is obstructed (by heavy rain, snow, etc.)
Radar blocked See
manual
ACC has been temporarily disconnected because the radar is obstructed in some way and cannot detect
other vehicles.
In this situation, the driver can switch to standard cruise control, see Toggling between ACC and CC
(standard Cruise Control) (p. 149)
See Adaptive Cruise Control – limitations (p. 159) for information on the radar sensor’s limitations.
||
07 Driver support
07
162
Symbol Message
Description
-
Cruise control Service
required
ACC is not functioning.
Contact a trained and qualified Volvo service technician.
-
Press Brake To hold
+
an audible signal
The vehicle is at a standstill and ACC will release the brakes before the parking brake engages to keep
the vehicle stopped but a problem with the parking brake means that the vehicle may begin to roll.
The driver will have to apply the brakes. The message will remain in the display and the audible signal
will continue until the driver applies the brakes or presses the accelerator pedal.
-
Below 30 km/h Only
following
This is displayed if you try to activate ACC at speeds below approx. 18 mph (30 km/h) without a vehicle
ahead within range (approx. 100 ft/30 meters).
Related information
•
07 Driver support
07
163
Adaptive Cruise Control –
troubleshooting
If the message
Radar blocked See manual
is displayed, this means that the radar signals
from the sensor have been obstructed and
that a vehicle ahead cannot be detected.
This, in turn, means that the functions of the
ACC, Distance Alert, and Collision Warning
System with Auto-brake and Pedestrian
Detection will not function.
The table lists possible causes for this mes-
sage being displayed, and suitable actions.
Cause
Action
The surface of the radar in the grille is dirty or obstructed in some
way.
Clean the radar surface, or remove the object causing the obstruction.
Heavy rain or snow is interfering with the radar signals.
No action possible. Heavy precipitation may affect the function of the
radar.
Swirling water or snow from the surface of the road may interfere
with the radar signals.
No action possible. A very wet or snow-covered road surface may affect
the function of the radar.
The surface of the radar is clean but the message remains in the
display.
Wait a short time. It may take several minutes for the radar to detect that
it is no longer obstructed.
Related information
•
07 Driver support
07
164
Distance Alert – introduction
Distance Alert is part of Adaptive Cruise Con-
trol and is a function that provides information
about the time interval to the vehicle ahead.
Introduction
Distance Alert is active at speeds above
approximately 18 mph (30 km/h). Time inter-
val information is only given for a vehicle that
is driving ahead of your vehicle in the same
direction. No information is provided for vehi-
cles driving toward you, moving very slowly,
or at a standstill.
Amber warning light
3
.
An amber warning light in the windshield
glows steadily if your vehicle is closer to the
one ahead than the set time interval.
Distance Alert only monitors distance to
the vehicle ahead while Adaptive Cruise
Control is in standby mode or off.
WARNING
Distance Alert only indicates the distance
to the vehicle ahead. It does not affect the
speed of your vehicle.
Related information
•
Distance Alert – operation (p. 164)
•
Distance Alert – limitations (p. 165)
•
Distance Alert – symbols and messages
Distance Alert – operation
Distance Alert is part of Adaptive Cruise Con-
trol and is a function that provides information
about the time interval to the vehicle ahead.
Press the button in the center instrument
panel to switch this function on or off. The
indicator light in the button illuminates when
the function is on.
Depending on the optional equipment
selected, there may not be room for a Dis-
tance Alert button in the center console. In
this case, the function is controlled through
the menu system. Press MY CAR and go to
Settings
Car settings
Distance alert
On/Off
.
3
The illustration is generic; certain details may vary from model to model
07 Driver support
07
}}
165
Setting a time interval
Controls and display
Time interval: Increase/decrease
Time interval On
Press
to increase the interval or
to
decrease it.
Five different time intervals
can be selected and are
shown in the display as 1–5
horizontal bars. The greater
the number of bars, the
longer the time interval. One
bar represents approximately
1 second to the vehicle ahead; 5 bars is
approximately 3 seconds.
•
The higher your vehicle’s speed, the
greater the distance to the vehicle
ahead, measured in feet (meters), for a
given time interval.
•
The set time interval is also used by
Adaptive Cruise Control, see Adaptive
Cruise Control – setting speed (p. 154).
WARNING
Only use a time interval that is suitable in
current traffic conditions.
Related information
•
Distance Alert – introduction (p. 164)
•
Distance Alert – limitations (p. 165)
•
Distance Alert – symbols and messages
Distance Alert – limitations
Distance Alert is part of Adaptive Cruise Con-
trol and is a function that provides information
about the time interval to the vehicle ahead.
Limitations
Distance Alert uses the same radar sensor
used by Adaptive Cruise Control and the Col-
lision Warning system. See Adaptive Cruise
Control – limitations (p. 159) for more infor-
mation on the radar sensor’s limitations.
Strong sunlight, reflections, extreme light
contrasts, the use of sunglasses, or if the
driver is not looking straight ahead may
make the visual warning signal in the wind-
shield difficult to see.
WARNING
•
Bad weather or winding roads may
affect the radar sensor’s capacity to
detect vehicles ahead.
•
The size of the vehicle ahead, such as
a motorcycle, may also make it difficult
to detect. This may result in the warn-
ing light illuminating at a shorter dis-
tance than the one that has been set,
or that the light will not come on at all.
||
07 Driver support
07
166
Related information
•
Distance Alert – introduction (p. 164)
•
Distance Alert – operation (p. 164)
•
07 Driver support
07
167
Distance Alert – symbols and
messages
Distance Alert is part of Adaptive Cruise Con-
trol and is a function that provides information
about the time interval to the vehicle ahead.
Symbols and text messages
A text message can be erased by pressing
briefly on the OK button on the turn signal
lever.
Symbol Message
Description
Radar blocked See
manual
Distance Alert has been temporarily disconnected because the radar is obstructed in some way and can-
not detect other vehicles. See Adaptive Cruise Control – limitations (p. 159) for information on the radar
sensor’s limitations.
Collision warn. Serv-
ice required
Distance Alert or Collision Warning with Full Auto-brake and Pedestrian Detection is not functioning prop-
erly. Contact a trained and qualified Volvo service technician.
Related information
•
Distance Alert – introduction (p. 164)
•
Distance Alert – operation (p. 164)
•
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст