Toyota Camry (2018 year). Manual — part 97
398
5-4. Other interior features
®
button (inside the
vehicle) for 2 seconds and
release it. Repeat this
sequence (press/hold/
release) up to 3 times to
complete programming.
If the garage door opener
motor operates when the
HomeLink
®
button is
pressed, the garage door
opener motor recognizes the
HomeLink
®
signal.
■
Enabling 2-way communication with a garage door (only avail-
able for compatible devices)
When enabled, 2-way communication allows you to check the sta-
tus of the opening and closing of a garage door through indicators
in your vehicle.
2-way communication is only available if the garage door opener
motor used is a compatible device. (To check device compatibility,
refer to www.HomeLink.com.)
Within 5 seconds after programming the garage door opener has
been completed, if the garage door opener motor is trained to
HomeLink
®
, both garage door operation indicators will flash rap-
idly green and the light on the garage door opener motor will
blink twice, indicating that 2-way communication is enabled.
If the indicators do not flash, perform
and
within the first 10
presses of the HomeLink
®
button after programming has been
completed.
Press a programmed HomeLink
®
button to operate a garage
door.
Within 1 minute of pressing the HomeLink
®
button, after the
garage door operation has stopped, press the “Learn” or “Smart”
button on the garage door opener motor. Within 5 seconds of the
establishment of 2-way communication with the garage door
opener, both garage door operation indicators in the vehicle will
flash rapidly green and the light on the garage door opener motor
will blink twice, indicating that 2-way communication is enabled.
3
1
2
3
2
3
399
5-4. Other interior features
In
te
rior fe
atures
■
Reprogramming a single HomeLink
®
button
When the following procedure is performed, buttons which already
have devices registered to them can be overwritten:
With one hand, press and hold the desired HomeLink
®
button.
When the HomeLink
®
indicator starts flashing orange, continue
to hold the HomeLink
®
button and perform “Programming the
HomeLink
®
”
(it takes 20 seconds for the HomeLink
®
indicator
to start flashing).
Press the appropriate HomeLink
®
button. The HomeLink
®
indicator
light should turn on.
The status of the opening and
closing of a garage door is shown
by the indicators.
Opening
Closing
This function is only available if the
garage door opener motor used is
a compatible device. (To check
device compatibility, refer to
www.HomeLink.com.)
The indicators can operate within approximately 820 ft. (250 m) of
the garage door. However, if there are obstructions between the
garage door and the vehicle, such as houses and trees, feedback
signals from the garage door may not be received. To recall the pre-
vious door operation status, press and release either HomeLink
®
buttons
and
or
and
simultane-
ously. The last recorded status will be displayed for 3 seconds.
Operating the HomeLink
®
Garage door operation indicators
1
2
1
1
2
Color
Status
Orange (flashing)
Currently opening/closing
Green
Opening/closing has completed
Red (flashing)
Feedback signals cannot be received
400
5-4. Other interior features
®
indicator light
changes from continuously lit
orange to rapidly flashing green.
If you sell your vehicle, be sure to
erase the programs stored in the
HomeLink
®
memory.
■
Codes stored in the HomeLink
®
memory
●
The registered codes are not erased even if the battery cable is discon-
nected.
●
If learning failed when registering a different code to a HomeLink
®
button
that already has a code registered to it, the already registered code will not
be erased.
■
Before programming
●
Install a new battery in the transmitter.
●
The battery side of the transmitter must be pointed away from the Home-
Link
®
.
■
Certification for the garage door opener
For vehicles sold in the U.S.A.
For vehicles sold in Canada
Erasing the entire HomeLink
®
memory (all three codes)
401
5-4. Other interior features
In
te
rior fe
atures
■
When support is necessary
Visit on the web at www.homelink.com/toyota or call 1-800-355-3515.
WARNING
■
When programming a garage door or other remote control device
The garage door or other device may operate, so ensure people and
objects are out of danger to prevent potential harm.
■
Conforming to federal safety standards
Do not use the HomeLink
®
compatible transceiver with any garage door
opener or device that lacks safety stop and reverse features as required by
federal safety standards. This includes any garage door that cannot detect
an interfering object. A door or device without these features increases the
risk of death or serious injury.
■
When operating or programming HomeLink
®
Never allow a child to operate or play with the HomeLink
®
buttons.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст