Toyota Urban Cruiser (2015 year). Instruction — part 14
2-1. Driving procedures
Horn
To sound the horn, press on or
close to the
mark.
2
■ After adjusting the steering wheel
Make sure that the steering wheel is securely locked.
The horn may not sound if the steering wheel is not securely locked.
(→P. 95)
195
URBAN CRUISER_OM_OM52F47E_(EE)
2-2. Instrument cluster
Gauges and meters
Instrument cluster light control button
To adjust the brightness of the instrument cluster light. (→P. 197)
Speedometer
Displays the vehicle speed.
“MODE” button
Switches the multi-information display. Pushing and holding the button
will reset the trip meter when the trip meter is being displayed.
Multi-information display
→P. 202
Tachometer
Displays the engine speed in revolutions per minute.
Fuel gauge and instrument cluster light control display
Displays the quantity of fuel remaining in the tank.
196
URBAN CRUISER_OM_OM52F47E_(EE)
2-2. Instrument cluster
Instrument cluster light control
To adjust the brightness of the instrument cluster lights, push the
switch.
Darker
Brighter
2
■ The meters and display illuminate when
Vehicles without a smart entry & start system
The engine switch is in the “ON” position.
Vehicles with a smart entry & start system
The “ENGINE START STOP” switch is in IGNITION ON mode.
NOTICE
■ To prevent damage to the engine and its components
●Do not let the indicator needle of the tachometer enter the red zone, which
indicates the maximum engine speed.
●The engine may be overheating if the high engine coolant temperature
warning light comes on. In this case, immediately stop the vehicle in a safe
place, and check the engine after it has cooled completely. (→P. 493)
197
URBAN CRUISER_OM_OM52F47E_(EE)
2-2. Instrument cluster
Indicators and warning lights
The indicator and warning lights on the instrument cluster and cen-
ter panel inform the driver of the status of the vehicle’s various sys-
tems.
Instrument cluster
Center panel
198
URBAN CRUISER_OM_OM52F47E_(EE)
2-2. Instrument cluster
■ Indicators
The indicators inform the driver of the operating state of the
vehicle’s various systems.
*1
Turn signal indicator
Four-wheel drive lock
(→P. 193)
indicator (→P. 229)
(4WD models
Headlight high beam
Low engine coolant
indicator (→P. 208)
temperature indicator
2
*1, 2
Tail light indicator
Slip indicator (→P. 224)
(→P. 207)
(if equipped)
*1, 4
Front fog light indicator
VSC OFF indicator
(→P. 211)
(→P. 225)
(if equipped)
(if equipped)
*1
Rear fog light indicator
“TRC OFF” indicator
(→P. 211)
(→P. 224)
*1
Engine preheating
Gear Shift Indicator
indicator (→P. 185, 181)
(→P. 190)
(diesel engine)
*1
*1
“ECO” indicator
“PASSENGER
(→P. 217)
AIRBAG” indicator
(if equipped)
(→P. 140)
*1
“ECO OFF” indicator
(→P. 217)
(if equipped)
199
URBAN CRUISER_OM_OM52F47E_(EE)
2-2. Instrument cluster
■ Warning lights
Warning lights inform the driver of malfunctions in any of the
vehicle’s systems. (→P. 439)
*1
*1
*1
*1
*1
*1
*1
*1
*1, 3
*1
(if equipped)
(diesel
(diesel
engine)
engine)
*1
*1, 3
(diesel
(if equipped)
(4WD
engine)
models)
*1: These lights turn on when the engine switch is turned to the “ON”
position
(vehicles without a smart entry & start system) or the
“ENGINE START STOP” switch is turned to IGNITION ON mode
(vehicles with a smart entry & start system) to indicate that a
system check is being performed. They will turn off after the engine
is started, or after a few seconds. There may be a malfunction in a
system if a light does not come on, or if the lights do not turn off.
Have the vehicle inspected by any authorized Toyota dealer or
repairer, or another duly qualified and equipped professional for
details.
*2: The indicator flashes to indicate that the system is operating.
*3: The indicator comes on to indicate a malfunction.
*4: The indicator comes on to indicate that the system is off.
200
URBAN CRUISER_OM_OM52F47E_(EE)
2-2. Instrument cluster
CAUTION
■ If a safety system warning light does not come on
Should a safety system light such as the ABS or SRS warning light not come
on when you start the engine, this could mean that these systems are not
available to help protect you in an accident, which could result in death or
serious injury. Have the vehicle inspected by any authorized Toyota dealer or
repairer, or another duly qualified and equipped professional immediately if
this occurs.
2
201
URBAN CRUISER_OM_OM52F47E_(EE)
2-2. Instrument cluster
Multi-information display
The multi-information display presents the driver with a variety of
driving-related data.
● Odometer/trip meter display
(→P. 203)
● Trip information
(→P. 203)
Displays driving range, fuel
consumption and other cruis-
ing-related information.
● Outside temperature display
(→P. 204)
Indicates the outside tempera-
ture.
Switch the display
Display items can be switched
by pressing the “MODE” button.
202
URBAN CRUISER_OM_OM52F47E_(EE)
2-2. Instrument cluster
● Odometer
Displays the total distance the vehicle has been
driven.
● Trip meters A and B
Displays the distance the vehicle has been driven
since the meter was last reset. Trip meters A and
2
B can be used to record and display different dis-
tances independently.
Press and hold the button to reset.
● Instantaneous fuel consumption
Displays the instantaneous fuel consumption.
● Average fuel consumption
Displays the average fuel consumption since the
vehicle was last refueled.
Use the displayed average fuel consumption as a
reference.
203
URBAN CRUISER_OM_OM52F47E_(EE)
2-2. Instrument cluster
● Average vehicle speed
Displays the average vehicle speed since the
engine was started.
● Driving range
Displays the estimated maximum distance that
can be driven with the quantity of fuel remaining.
• This distance is computed based on your aver-
age fuel consumption. As a result, the actual dis-
tance that can be driven may differ from that
displayed.
• When only a small amount of fuel is added to the
tank, the display may not be updated.
● Outside temperature display
Displays the outside temperature.
The temperature range that can be displayed is
from -40°C (-40°F) to 50°C (122°F).
When the outside air temperature falls below 3°C
(37°F) while driving, the temperature display flashes
to indicate that the outside air temperature is
becoming low.
204
URBAN CRUISER_OM_OM52F47E_(EE)
2-2. Instrument cluster
● Stop & Start system total operation time (if equipped)
Displays the total amount of time that the engine
has been stopped due to operation of the Stop &
Start system since the system was last reset.
Press and hold the button to reset.
● Stop & Start system operation time (if equipped)
Displays the amount of time the engine was
2
stopped due to operation of the Stop & Start sys-
tem during the current trip (from the “ENGINE
START STOP” switch in the IGNITION ON mode
to the OFF [vehicles with smart entry & start sys-
tem] or from the engine switch in the “ON” posi-
tion to the
“LOCK” position
[vehicles without
smart entry & start system]).
205
URBAN CRUISER_OM_OM52F47E_(EE)
2-2. Instrument cluster
■ Outside temperature display
● In the following situations, the correct outside temperature may not be
displayed, or the display may take longer than normal to change.
• When stopped, or driving at low speeds (less than 20 km/h [12 mph])
• When the outside temperature has changed suddenly (at the entrance/
exit of a garage, tunnel, etc.)
● When “--” is displayed, the system may be malfunctioning.
Take your vehicle to any authorized Toyota dealer or repairer, or another
duly qualified and equipped professional.
NOTICE
■ The multi-information display at low temperatures
Allow the interior of the vehicle to warm up before using the liquid crystal
information display. At extremely low temperatures, the information display
monitor may respond slowly, and display changes may be delayed.
206
URBAN CRUISER_OM_OM52F47E_(EE)
2-3. Operating the lights and wipers
Headlight switch
The headlights can be operated manually.
Turning the end of the lever turns on the lights as follows:
The front position, tail,
license plate lights
turn on.
The headlights and all
lights listed above turn
2
on.
207
URBAN CRUISER_OM_OM52F47E_(EE)
2-3. Operating the lights and wipers
Turning on the high beam headlights
With the headlights on, push
the lever forward to turn on the
high beams.
Pull the lever back to the center
position to turn the high beams
off.
Pull the lever toward you to
turn on the high beams.
Release the lever to turn them off.
You can flash the high beams
with the headlights on or off.
208
URBAN CRUISER_OM_OM52F47E_(EE)
2-3. Operating the lights and wipers
Manual headlight leveling dial
The level of the headlights can be adjusted according to the number
of passengers and the loading condition of the vehicle.
Raises the level of the head-
lights
Lowers the level of the head-
lights
2
■ Guide to dial settings
Occupancy and luggage load conditions
Dial position
2WD
4WD
Occupants
Luggage load
models
models
Driver
None
0
0
Driver and front
None
0.5
0.5
passenger
All seats occupied
None
1.5
2.0
All seats occupied
Full luggage loading
2.0
2.5
Driver
Full luggage loading
3.0
3.5
209
URBAN CRUISER_OM_OM52F47E_(EE)
Большое спасибо!
Ваше мнение очень важно для нас.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст