Toyota Sequoia (2005). Manual — part 256
![](/vehicles/linovind/vere/fry/zeex.png)
F19134
ON
OFF
0.25 sec.
0.25 sec.
F19133
0.125 sec.
0.125 sec.
ON
OFF
–
DIAGNOSTICS
TIRE PRESSURE WARNING SYSTEM
DI–819
1013
*2: Comes on and goes off repeatedly at 0.25 second intervals.
*3: Comes on and goes off repeatedly at 0.125 second inter-
vals.
![](/vehicles/linovind/vere/fry/ksin.png)
DIDK4–01
D13491
DLC3:
CG
TC
F19148
Combination Meter
Tire Pressure
Warning Lamp
F19128
ON
0.25 sec.
OFF
0.25 sec.
0.5 sec.
1.5 sec.
4.5 sec.
2.5 sec.
0.5 sec.
ON
OFF
Normal System Code:
Code 13 and 33:
1.5 sec.
Repeat
D05981
DLC3
Hand–Held
Tester
DI–820
–
DIAGNOSTICS
TIRE PRESSURE WARNING SYSTEM
1014
DTC CHECK / CLEAR
1.
DTC CHECK (USING SST CHECK WIRE)
(a)
Check DTCs.
(1)
Using the SST, connect terminals TC and CG of
DLC3.
SST
09843–18040
(2)
Turn the ignition switch to the ON position.
(3)
Read and record any DTCs from the tire pressure
warning lamp on the combination meter. Refer to
the illustration on the left for examples of a normal
system code and codes 13 and 33.
HINT:
If the tire pressure warning lamp does not blink any DTCs
or the normal system code, inspect the tire pressure
warning lamp circuit or TC terminal circuit.
Trouble Area
See page
Tire pressure warning lamp circuit
TC terminal circuit
If 2 or more malfunctions are indicated at the same time,
the lowest numbered DTC is displayed first.
(4)
Refer to the Diagnostic Trouble Code Chart (see
page
(5)
After completing the check, turn the ignition switch
off and remove the SST from DLC3.
SST
09843–18040
2.
DTC CHECK (USING HAND–HELD TESTER)
(a)
Check DTCs.
(1)
Connect the hand–held tester to the DLC3.
(2)
Turn the ignition switch to the ON position.
(3)
Read the DTCs following the prompts on the tester
screen.
HINT:
Refer to the hand–held tester operator’s manual for further de-
tails.
–
DIAGNOSTICS
TIRE PRESSURE WARNING SYSTEM
DI–821
1015
3.
DTC CLEAR
HINT:
After repairing the malfunctions, clear the DTCs.
(a)
Connect the hand–held tester to DLC3.
(b)
Turn the ignition switch to the ON position.
(c)
Erase the DTCs following the prompts on the tester
screen.
HINT:
Refer to the hand–held tester operator’s manual for further de-
tails.
![](/vehicles/linovind/vere/fry/berdorey.png)
DIDK5–01
DI–822
–
DIAGNOSTICS
TIRE PRESSURE WARNING SYSTEM
1016
DATA LIST / ACTIVE TEST
1.
DATA LIST
(a)
Connect the hand–held tester to DLC3.
(b)
Turn the ignition switch to the ON position.
(c)
Following the display on the hand–held tester, read the ”DATA LIST”.
Item
Measurement item/
Range (Display)
Normal Condition
Diagnostic Note
MODE STATUS
Tire pressure warning system
mode/NORMAL or REG 2nd or
REG M or TEST
NORMAL: Normal mode
TEST: Test mode
–
MAIN TIRE
Number of main tire ID to be regis-
tered/0 or 1 or 2 or 3 or 4 or 5
0 to 5 should be displayed
–
2ND TIRE
Number of 2ND tire ID to be regis-
tered/0 to 1 or 2 or 3 or 4 or 5
0 to 5 should be displayed
–
SELECT SW
Select switch/Main, 2nd
Main
–
INITIAL SW
Initialization switch/ON, OFF
ON: Switch on
OFF: Switch off
–
VEHICLE SPEED
Vehicle speed reading/
min.: 0 km/h (0 mph),
max.: 255 km/h (158 mph)
Actual vehicle speed
Speed indicated on the
combination meter
REGIT ID1 CODE
Registered ID1 code/min.: 0,
max.: FFFFFFF
The ID No. registered in the trans-
mitter ID1 is displayed
–
REGIT ID2 CODE
Registered ID2 code/min.: 0,
max.: FFFFFFF
The ID No. registered in the trans-
mitter ID2 is displayed
–
REGIT ID3 CODE
Registered ID3 code/min.: 0,
max.: FFFFFFF
The ID No. registered in the trans-
mitter ID3 is displayed
–
REGIT ID4 CODE
Registered ID4 code/min.: 0,
max.: FFFFFFF
The ID No. registered in the trans-
mitter ID4 is displayed
–
REGIT ID5 CODE
Registered ID5 code/min.: 0,
max.: FFFFFFF
The ID No. registered in the trans-
mitter ID5 is displayed
–
TRANS STATUS
ID code transmission status/
FINISH or NOW
FINISH or NOW
–
TIREPRESS1
ID1 tire inflation pressure/
min.: 0 kPa (0 kgf
⋅
cm
2
, 0 psi),
max.: 637.5 kPa (6.48 kgf
⋅
cm
2
,
92.2 psi)
Actual tire inflation pressure
–
TIREPRESS2
ID2 tire inflation pressure/
min.: 0 kPa (0 kgf
⋅
cm
2
, 0 psi),
max.: 637.5 kPa (6.48 kgf
⋅
cm
2
,
92.2 psi)
Actual tire inflation pressure
–
TIREPRESS3
ID3 tire inflation pressure/
min.: 0 kPa (0 kgf
⋅
cm
2
, 0 psi),
max.: 637.5 kPa (6.48 kgf
⋅
cm
2
,
92.2 psi)
Actual tire inflation pressure
–
TIREPRESS4
ID4 tire inflation pressure/
min.: 0 kPa (0 kgf
⋅
cm
2
, 0 psi),
max.: 637.5 kPa (6.48 kgf
⋅
cm
2
,
92.2 psi)
Actual tire inflation pressure
–
TIREPRESS5
ID5 tire inflation pressure/
min.: 0 kPa (0 kgf
⋅
cm
2
, 0 psi),
max.: 637.5 kPa (6.48 kgf
⋅
cm
2
,
92.2 psi)
Actual tire inflation pressure
–
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст