Toyota Sequoia (2005). Manual — part 778
SA24D–04
F14486
40 mm
(1.57 in.)
F14485
SST
F14484
SST
–
SUSPENSION AND AXLE
REAR DIFFERENTIAL FRONT OIL SEAL
SA–105
3101
REPLACEMENT
1.
DRAIN DIFFERENTIAL OIL
2.
DISCONNECT REAR PROPELLER SHAFT
2WD: See page
3.
REMOVE COMPANION FLANGE
(a)
2WD:
Remove the companion flange nut.
(1)
Using a chisel and hammer, loosen the staked part
of the nut.
(2)
Install the 3 stud bolts so that the heads come out
40 mm (1.57 in.).
(3)
Set the SST and install the 3 nuts to the companion
flange.
SST
09213–58013
(4)
Install the other SST to the set SST to hold the com-
panion flange, and remove the nut.
SST
09330–00021
(5)
Remove the 3 nuts, SST and stud bolts from the
companion flange.
SA2349
SST
R13357
SST
R13358
SST
SST
R13359
SST
SA–106
–
SUSPENSION AND AXLE
REAR DIFFERENTIAL FRONT OIL SEAL
3102
(b)
4WD:
(1)
Using a chisel and hammer, loosen the staked part
of the nut.
(2)
Using SST to hold the flange, remove the nut.
SST
09330–00021
(c)
Using SST, remove the companion flange.
SST
09950–30012 (09951–03010, 09953–03010,
09954–03010, 09955–03030, 09956–03050)
4.
REMOVE OIL SEAL
Using SST, remove the oil seal.
SST
09308–10010
5.
REMOVE FRONT BEARING
Using SST, remove the front bearing from the drive pinion.
SST
09556–22010
6.
REMOVE BEARING SPACER
(a)
Remove the 2 washers.
(b)
Remove the bearing spacer.
7.
INSTALL NEW BEARING SPACER
(a)
Install a new bearing spacer.
(b)
Install the 2 washers.
8.
INSTALL FRONT BEARING
(a)
Place the front bearing.
R13361
SST
R13360
SST
Vinyl Tape
F14486
40 mm
(1.57 in.)
F14485
SST
F14522
SST
–
SUSPENSION AND AXLE
REAR DIFFERENTIAL FRONT OIL SEAL
SA–107
3103
(b)
Using SST and the companion flange, install the front
bearing then remove the companion flange.
SST
09950–30012 (09951–03010, 09953–03010,
09954–03010, 09955–03030, 09956–03050)
9.
INSTALL NEW OIL SEAL
(a)
Coat a new oil seal lip with MP grease.
(b)
Using SST and a plastic hammer, install the oil seal until
its surface is flush with the differential carrier end.
SST
09316–12010, 09649–17010
HINT:
Connect 2 SST with vinyl tape.
10.
INSTALL COMPANION FLANGE
(a)
Place the companion flange on the drive pinion.
(b)
Coat the threads of a new nut with hypoid gear oil.
(c)
2WD:
Install the companion flange nut.
(1)
Install the 3 stud bolts so that the heads come out
40 mm (1.57 in.).
(2)
Set the SST and install the 3 nuts to the companion
flange .
SST
09213–58013
(3)
Install the other SST to the set SST to hold the com-
panion flange and torque the nut.
SST
09330–00021
Torque: 147 N·m (1,500 kgf·cm, 109 ft·lbf)
(4)
Remove the 3 nuts, SST and stud bolts from the
companion flange.
FA1083
SST
FA1084
R13337
Less than
5 mm (0.20 in.)
SA–108
–
SUSPENSION AND AXLE
REAR DIFFERENTIAL FRONT OIL SEAL
3104
(d)
4WD:
Using SST to hold the flange, torque the nut.
SST
09330–00021
Torque: 147 N·m (1,500 kgf·cm, 109 ft·lbf)
11.
ADJUST DRIVE PINION PRELOAD
(See page
)
12.
STAKE DRIVE PINION NUT
13.
CONNECT REAR PROPELLER SHAFT
2WD: See page
14.
FILL DIFFERENTIAL WITH HYPOID GEAR OIL
Torque: 49 N·m (500 kgf·cm, 36 ft·lbf)
Oil type: Hypoid gear oil API GL–5
Recommended oil viscosity:
SAE 75W – 140 (Synthetic)
Capacity: 3.65 liters (3.86 US qts, 3.21 Imp. qts)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст