Toyota Sequoia (2005). Manual — part 572
![](/vehicles/linovind/vere/fry/oues.png)
DIDAW–01
Vehicle brought into a workshop
4. Check the diagnostic trouble codes
DTC is not output (Go to step 6)
5. Diagnostic trouble code chart.
Go to step 7
7. Circuit inspection and part inspection
10. Perform confirmation test
END
Items inside
are titles of pages in this manual,
with the page number in the bottom portion. See
the pages for detailed explanations.
P.
P.
P.
1. Customer problem analysis
P.
2. Problem Symptom Confirmation
Symptom does
not occur
Malfunction
code
6. Problem symptoms table
P.
8. Identification of problem
Symptom occurs
Go to step 4
3. Symptom Simulation
P.
9. Repair or replace
Normal system
code
–
DIAGNOSTICS
REAR SEAT ENTERTAINMANT SYSTEM
DI–2083
2277
HOW TO PROCEED WITH TROUBLESHOOTING
![](/vehicles/linovind/vere/fry/xpi.png)
DIDAX–01
I28289
RSE SYSTEM Check Sheet
Inspector’s name:
Customer’s Name
VIN
Production Date
Licence Plate No.
Odometer Reading
/ /
km
mile
Frequency of Problem Occurrence
/ /
Constant
Intermittent ( Times a day)
Brought–in Date
Problem
Symptom
Headphone
DTC
Check
Parts name
DTC (1st time).
DTC (2nd time).
Switch Assy
Disc Player Controller
Multi–display Controller Sub–assy
Television Display Assy
Disc Player Controller
Television Display Assy
DI–2084
–
DIAGNOSTICS
REAR SEAT ENTERTAINMANT SYSTEM
2278
CUSTOMER PROBLEM ANALYSIS CHECK
![](/vehicles/linovind/vere/fry/hicheryag.png)
DIDAY–01
I28281
”Diagnosis MENU”
to section
Press ENTER on
remote control
The entire screen is changed
to the color which is selected
in the color bar check mode.
Select color by
remote control
operation
–
DIAGNOSTICS
REAR SEAT ENTERTAINMANT SYSTEM
DI–2085
2279
DISPLAY CHECK MODE
DISPLAY CHECK MODE
HINT:
Illustrations may differ from the actual vehicle depending on the device settings and options. There-
fore, some detailed areas may not be shown exactly the same as on the actual vehicle.
Display check mode is operated as follows.
![](/vehicles/linovind/vere/fry/ppandex.png)
I28282
*2
*1
I28283
The entire screen is
changed to the color
which is selected in
the color bar check
mode.
Press ENTER
on remote
control
Select color by
remote control
operation
I28284
DI–2086
–
DIAGNOSTICS
REAR SEAT ENTERTAINMANT SYSTEM
2280
(a)
Display Check Mode
Display
Contents
Color Bar Check/*1
Color display is checked.
Remote Commander/*2
Operating condition of remote command-
er display is checked.
HINT:
In Display Check Mode, above checks can be performed.
(b)
Display Color Bar Check
(1)
Start the Diagnosis System (See page
(2)
Select ”MENU”.
(3)
Select ”Display Check”.
(4)
Select ”Color Bar Check”.
(5)
Make sure that each color name is corresponding
to each color on the bar.
HINT:
Select Black, Red, Green, Blue, White and Stripe to display se-
lected colors and stripe on the entire screen.
(6)
Compare the color with the Color Bar Check, and
make sure that the color is the same.
(c)
Display Remote Commander Check
(1)
Start the Diagnosis system (See page
(2)
Select ”MENU”.
(3)
Select ”Display Check”.
(4)
Select ”Remote Commander”.
(5)
Press each switch and make sure that it corre-
sponds to the display on the screen.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст