Toyota Sequoia (2005). Manual — part 53
START
Confirm vehicle VIN
Preparation:
1. Connect hand–held tester to DLC3
2. Turn ignition switch to ON
3. Turn tester ON
Hand–held tester operation:
1. Select DIAGNOSIS
2. Select ENHANCED OBD ll
READ:
Menu Screen:
*********************************
[ VIN ]
*********************************
PRESS [EXIT]
ERROR
PRESS [EXIT]
DTC P0630 was detected.
P0630 [VIN Not Programmed
or Mismatch – ECM/PCM]
Please input the VIN.
PRESS [EXIT]
Possible cause:
To Menu Screen
17–digit VIN
displayed
3. Select VIN
DTC P0630 Set
VIN Previously Stored
VIN Not Stored
[EXIT]
[EXIT]
[EXIT]
2. VIN WRITE
VIN
Select VIN READ
1. VIN READ
1. VIN READ
ERROR
ECM does not respond the VIN.
1: VIN is not written yet.
2: Vehicle does not support this
function.
–
DIAGNOSTICS
ENGINE
DI–15
209
3.
READ VIN (Vehicle Identification Number)
(a)
Read VIN using a hand–held tester.
START
Confirm vehicle VIN
Preparation:
1. Connect hand–held tester to DLC3
2. Turn ignition switch to ON
3. Turn tester ON
Hand–held tester operation:
Write:
Menu Screen:
This function overwrites the
following VIN with a new VIN.
*********************************
[ VIN ]
*********************************
[YES] to Continue
[NO] to EXIT
To Menu Screen
Continued on next page
NOTICE
Do you wish to continue?
[YES]
[NO]
1. Select DIAGNOSIS
2. Select ENHANCED OBD ll
3. Select VIN
1. VIN READ
1. VIN READ
VIN
Select VIN WRITE
[YES] or [NO]
[YES]
2. VIN WRITE
To Menu
Screen
[NO]
CONFIRMATION
This function will erase the
DTCs automatically after
writing the VIN.
Do you wish to continue?
[YES]
17–digit VIN displayed
VIN Previously Stored
DI–16
–
DIAGNOSTICS
ENGINE
210
4.
WRITE VIN
(a)
Write VIN using the hand–held tester.
Your VIN is incorrect.
Please enter the VIN again.
Input a new VIN
PRESS [ENTER]
If you want to clear the VIN,
press [NO] key.
To Menu Screen
Writing Successful
[ENTER]
Continued from previous page
WRITING COMPLETE
NOW WRITING
Input Error
INPUT ERROR
[EXIT] to RETURN
[EXIT]
WRITING FAILED
Turn IG OFF, then ON,
Please try again.
PRESS [EXIT]
[EXIT]
Writing Error
SET NEW VIN
Press [RIGHT]/[LEFT] to shift
the cursor right/left.
Press [UP]/[DOWN] to
increase/decrease value.
Or, input digit with the 10 key.
PRESS [ENTER]
CONFIRMATION
PRESS [ENTER]
Vehicle is stopped.
New Registration
[ENTER]
[ENTER]
PRESS [ENTER]
Communication Error
[ENTER]
COMMUNICATION ERROR
PRESS [EXIT]
Turn IG OFF, then ON.
VIN input method
The following VIN has been
written correctly.
The DTCs have been erased
correctly.
To Menu Screen
To Menu Screen
[EXIT]
Input Instructions
Engine is not running.
–
DIAGNOSTICS
ENGINE
DI–17
211
DID7U–01
A21570
DI–18
–
DIAGNOSTICS
ENGINE
212
LIST OF DISABLE A MONITOR
HINT:
This table indicates ECM monitoring status for the items in the upper columns if the DTCs in each line on
the left are being set.
As for the ”X” mark, when the DTC on the left is stored, detection of the DTC in the upper column is not per-
formed.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст