Toyota Tundra. Manual — part 2289
![](/vehicles/linovind/mig/oudithero/quna.png)
Fig. 12: Identifying O-Ring
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
5. ADD ENGINE OIL
a. Add fresh oil.
Standard Oil Grade
STANDARD OIL GRADE SPECIFICATIONS STANDARD OIL GRADE
SPECIFICATIONS
Standard Oil Capacity
STANDARD OIL CAPACITY SPECIFICATIONS STANDARD OIL CAPACITY
SPECIFICATIONS
b. Install the oil filler cap.
6. INSPECT FOR OIL LEAK
a. Start the engine. Make sure that there are no oil leaks from the area that was worked on.
7. INSPECT ENGINE OIL LEVEL (See ON-VEHICLE INSPECTION )
Oil Grade
Oil Viscosity (SAE)
ILSAC multigrade engine
oil
0W-20
5W-20 (0W-20 is best choice for fuel economy and good starting in
cold weather.)
Item
Specified Condition
Drain and refill with oil filter change
7.0 liters (7.4 US qts, 6.2 lmp. qts)
Drain and refill without oil filter change 6.6 liters (7.0 US qts, 5.8 lmp. qts)
Dry fill
8.4 liters (8.9 US qts, 7.4 lmp. qts)
2009 Toyota Tundra
2009 ENGINE Lubrication (3UR-FBE) - Tundra
![](/vehicles/linovind/mig/oudithero/tosab.png)
8. INSTALL NO. 1 ENGINE UNDER COVER
a. Hook the engine under cover to the vehicle body as shown in the illustration.
b. Install the 3 screws and 5 bolts.
Torque: for bolt
29 N*m (296 kgf*cm, 21 ft.*lbf)
for screw
5.4 N*m (55 kgf*cm, 48 in.*lbf)
Fig. 13: Locating No. 1 Engine Under Cover Screws And Bolts
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
OIL PRESSURE SWITCH
COMPONENTS
2009 Toyota Tundra
2009 ENGINE Lubrication (3UR-FBE) - Tundra
![](/vehicles/linovind/mig/oudithero/hebernorut.png)
Fig. 14: Identifying Oil Pressure Sender Gauge Assembly And Related Components With Torque
Specifications
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
ON-VEHICLE INSPECTION
1
INSPECT OIL PRESSURE SENDER GAUGE ASSEMBLY
2009 Toyota Tundra
2009 ENGINE Lubrication (3UR-FBE) - Tundra
![](/vehicles/linovind/mig/oudithero/poud.png)
Fig. 15: Inspecting Oil Pressure Sender Gauge Assembly
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
a
Disconnect the sender gauge connector
b
Apply battery positive (+) voltage to the sender gauge terminal through a test LED
c
Check that the LED does not illuminate when the engine is stopped
d
Check that the LED flashes when the engine is running The number of flashes varies with engine
speed
If the operation is not as specified, replace the oil pressure sender gauge assembly
REMOVAL
1
REMOVE NO. 1 ENGINE UNDER COVER (See REPLACEMENT )
2
REMOVE OIL PRESSURE SENDER GAUGE ASSEMBLY
a
Disconnect the sender gauge connector
Fig. 16: Locating Sender Gauge Connector
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
2009 Toyota Tundra
2009 ENGINE Lubrication (3UR-FBE) - Tundra
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст