Toyota Tundra. Manual — part 2375

2

REMOVE NO. 1 ENGINE UNDER COVER (See REPLACEMENT )

3

REMOVE V-BANK COVER (See REMOVAL )

4

REMOVE AIR CLEANER HOSE ASSEMBLY (See REMOVAL )

5

REMOVE AIR CLEANER ASSEMBLY (See REMOVAL )

6

REMOVE FAN AND GENERATOR V BELT (See )

7

REMOVE FRONT FENDER APRON SEAL RH (See REMOVAL )

8

DISCONNECT VANE PUMP ASSEMBLY

a

Disconnect the 2 clamps and power steering oil pressure switch connector

Fig. 9: Locating Power Steering Oil Pressure Switch Connector Clamps
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.

b

Remove the 2 bolts and disconnect the vane pump

Fig. 10: Locating Vane Pump Bolts
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.

OFF, wait 90 seconds or more before disconnecting the cable from
the negative (-) battery terminal.

2009 Toyota Tundra

2009 ENGINE Starting (3UR-FE) - Tundra

9

REMOVE GENERATOR ASSEMBLY

a

Disconnect the generator connector

b

Remove the terminal cap and nut, and disconnect the generator wire

Fig. 11: Locating Generator Connector Terminal Cap And Nut
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.

c

Remove the bolt and disconnect the wire harness bracket from the generator

Fig. 12: Locating Wire Harness Bracket Bolt
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.

d

Remove the 2 bolts, 2 nuts and generator

Fig. 13: Locating Generator Nuts And Bolts
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.

2009 Toyota Tundra

2009 ENGINE Starting (3UR-FE) - Tundra

10

REMOVE ENGINE OIL LEVEL DIPSTICK GUIDE

a

Remove the dipstick

b

Remove the bolt and dipstick guide

c

Remove the O-ring from the dipstick guide

Fig. 14: Locating Dipstick Guide Bolt
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.

11

REMOVE FRONT EXHAUST PIPE ASSEMBLY

a

Disconnect the air fuel ratio sensor connector

b

Disconnect the heated oxygen sensor connector and 2 clamps

c

Remove the 2 bolts

d

Remove the 3 nuts and front exhaust pipe

e

Remove the 2 gaskets

12

REMOVE NO. 1 EXHAUST MANIFOLD HEAT INSULATOR (See REMOVAL )

13

REMOVE EXHAUST MANIFOLD SUB-ASSEMBLY RH (See REMOVAL )

14

REMOVE STARTER COVER

a

Remove the 3 bolts and starter cover

Fig. 15: Locating Starter Cover Bolts
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.

15

REMOVE STARTER ASSEMBLY

a

Disconnect the starter connector

2009 Toyota Tundra

2009 ENGINE Starting (3UR-FE) - Tundra

b

Remove the nut and disconnect the starter wire

Fig. 16: Locating Starter Connector Nut
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.

c

Remove the 2 bolts and starter

Fig. 17: Locating Starter Bolts
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.

d

Remove the flywheel housing side cover

Fig. 18: Locating Flywheel Housing Side Cover
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.

DISASSEMBLY

1

REMOVE MAGNET STARTER SWITCH ASSEMBLY

a

Remove the nut, and disconnect the lead wire from the magnet starter switch

2009 Toyota Tundra

2009 ENGINE Starting (3UR-FE) - Tundra