Toyota Tundra. Manual — part 995

1. REMOVE REAR WHEEL LH

2. DISCONNECT REAR DISC BRAKE CYLINDER ASSEMBLY LH

a. Remove the 2 bolts and disconnect the rear disc brake cylinder.

b. Hang the disc brake cylinder with a piece of wire.

3. REMOVE REAR DISC (See REMOVAL )

4. REMOVE PARKING BRAKE SHOE RETURN SPRING

a. Using SST, remove the return spring.

SST: 09703-30011

Fig. 45: Removing Return Spring Using SST
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.

5. REMOVE NO. 1 PARKING BRAKE SHOE ASSEMBLY LH

a. Using SST, remove the shoe hold down spring cup, compression spring and shoe hold down spring

pin.

SST 09718-00011

NOTE:



Do not disconnect the flexible hose from the disc brake
cylinder.



Do not twist or bend the flexible hose.

Fig. 44: Identifying Rear Disc Brake Cylinder Bolts
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.

2009 Toyota Tundra

2009 BRAKES Parking Brake - Tundra

b. Disconnect the tension spring from the No. 1 parking brake shoe.

c. Remove the No. 1 parking brake shoe and shoe adjuster screw set.

Fig. 46: Removing No. 1 Parking Brake Shoe And Shoe Adjuster Screw Set
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.

6. REMOVE NO. 2 PARKING BRAKE SHOE ASSEMBLY LH

a. Using SST, remove the shoe hold down spring cup, compression spring and shoe hold down spring

pin.

SST 09718-00011

b. Remove the No. 2 parking brake shoe.

Fig. 47: Removing No. 2 Parking Brake Shoe
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.

7. REMOVE PARKING BRAKE SHOE LEVER LH

a. Disconnect the No. 3 parking brake cable from the parking brake shoe lever.

b. Remove the parking brake shoe lever.

2009 Toyota Tundra

2009 BRAKES Parking Brake - Tundra

Fig. 48: Removing Parking Brake Shoe Lever
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.

8. REMOVE NO. 3 PARKING BRAKE CABLE ASSEMBLY

a. Remove the bolt and No. 3 parking brake cable.

Fig. 49: Identifying No. 3 Parking Brake Cable Bolt
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.

9. REMOVE PARKING BRAKE ANCHOR BLOCK

a. Remove the 2 nuts and anchor block.

Fig. 50: Identifying Parking Brake Anchor Block Nuts
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.

INSPECTION

2009 Toyota Tundra

2009 BRAKES Parking Brake - Tundra

1. CHECK BRAKE DISC INSIDE DIAMETER

a. Using a drum gauge or equivalent, measure the inside diameter of the disc.

Standard inside diameter:

240 mm (9.45 in.)

Maximum inside diameter:

241 mm (9.49 in.)

If the inside diameter of the disc is greater than the maximum, replace the disc.

Fig. 51: Measuring Inside Diameter Of Disc Using Drum Gauge
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.

2. CHECK PARKING BRAKE SHOE LINING THICKNESS

a. Using a ruler, measure the thickness of the shoe lining.

Standard thickness:

3.8 mm (0.148 in.)

Minimum thickness:

1.0 mm (0.0394 in.)

If the lining thickness is equal to or less than the minimum, or if severe or uneven wear is present,
replace the shoe.

2009 Toyota Tundra

2009 BRAKES Parking Brake - Tundra