Toyota Tundra. Manual — part 587

2. INSTALL NO. 1 RADIO BRACKET

a. Install the bracket with the 4 bolts.

Fig. 467: Identifying No. 1 Radio Bracket Bolts
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.

3. INSTALL NAVIGATION RECEIVER ASSEMBLY WITH BRACKET

a. Connect the connectors.

b. Insert the navigation receiver as shown in the illustration to attach the 3 clips on its backside.

Fig. 468: Removal/Installation Of Navigation Receiver
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.

c. Install the navigation receiver with the 4 bolts.

NOTE:

When inserting the navigation receiver, do not press the knobs on it.

2009 Toyota Tundra

2009 ACCESSORIES AND EQUIPMENT Navigation - Tundra

Fig. 469: Identifying Navigation Receiver With Bolts
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.

4. INSTALL INTEGRATION CONTROL AND PANEL ASSEMBLY (for Manual Air Conditioning

System) (See INSTALLATION )

5. INSTALL INTEGRATION CONTROL AND PANEL ASSEMBLY (for Automatic Air

Conditioning System) (See INSTALLATION )

6. INSTALL CENTER LOWER INSTRUMENT PANEL FINISH PANEL (See INSTALLATION )

7. INSTALL INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY (See INSTALLATION )

8. INSTALL FRONT CONSOLE BOX (See INSTALLATION )

9. INSTALL REAR CONSOLE BOX ASSEMBLY (See INSTALLATION )

10. INSTALL CONSOLE BOX CARPET (See INSTALLATION )

11. INSTALL REAR CONSOLE END PANEL SUB-ASSEMBLY (See INSTALLATION )

12. INSTALL REAR UPPER CONSOLE PANEL SUB-ASSEMBLY (See INSTALLATION )

13. INSTALL UPPER CONSOLE PANEL SUB-ASSEMBLY (See INSTALLATION )

14. INSTALL SHIFT LEVER KNOB SUB-ASSEMBLY (See INSTALLATION )

15. INSTALL LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY LH (See

INSTALLATION )

16. INSTALL INSTRUMENT SIDE PANEL LH (See INSTALLATION )

17. INSTALL COWL SIDE TRIM BOARD LH (See INSTALLATION )

18. INSTALL FRONT DOOR SCUFF PLATE LH

a. for Double Cab:

Install the front door scuff plate LH (See INSTALLATION ).

b. for CrewMax:

Install the front door scuff plate LH (see INSTALLATION ).

2009 Toyota Tundra

2009 ACCESSORIES AND EQUIPMENT Navigation - Tundra

19. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NAVIGATION ANTENNA

COMPONENTS

Fig. 470: Identifying Navigation Antenna Components
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.

NOTE:

Some systems need to be initialized after the cable is reconnected (see
INITIALIZATION ).

2009 Toyota Tundra

2009 ACCESSORIES AND EQUIPMENT Navigation - Tundra

REMOVAL

1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

2. REMOVE INSTRUMENT PANEL SUB-ASSEMBLY

a. for Column Shift Type:

Remove the instrument panel (see REMOVAL ).

b. for Floor Shift Type:

Remove the instrument panel (see REMOVAL ).

3. REMOVE NO. 1 HEATER TO REGISTER DUCT WITH NO. 2 HEATER TO REGISTER DUCT

(See DISASSEMBLY )

4. REMOVE NO. 2 SIDE DEFROSTER NOZZLE DUCT (See DISASSEMBLY )

5. REMOVE NO. 1 SIDE DEFROSTER NOZZLE DUCT (See DISASSEMBLY )

6. REMOVE DEFROSTER NOZZLE ASSEMBLY (See DISASSEMBLY )

7. REMOVE NAVIGATION ANTENNA ASSEMBLY

a. Detach the clamp.

b. Remove the 2 screws and antenna.

NOTE:



Some systems need to be initialized after the cable is reconnected
(see INITIALIZATION ).



After the ignition switch is turned OFF, the navigation system
requires approximately 90 seconds to record various types of
memory and settings. As a result, after turning the ignition switch
OFF, wait 90 seconds or more before disconnecting the cable from
the negative (-) battery terminal.

2009 Toyota Tundra

2009 ACCESSORIES AND EQUIPMENT Navigation - Tundra