Toyota Tundra. Manual — part 2757
![](/vehicles/linovind/mig/oudithero/anoh.png)
Fig. 73: Pressing Out Rear Spring Leaf Bush
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
REASSEMBLY
1. INSTALL REAR SPRING LEAF BUSH
a. Install a new bush to the leaf spring.
1. Install the bushing while aligning it with the matchmarks so that its openings are as shown in
the illustration.
b. Use SST and a press, press both bushes into the leaf spring.
SST 09710-28012 (09710-07062), 09710-30041 (09710-03211)
bush on the front side of the vehicle.
NOTE:
Be sure to install each bushing to the correct positions.
NOTE:
Align SST, which presses the bush, to the outer casing of the bush.
2009 Toyota Tundra
2009 SUSPENSION Suspension - Tundra
![](/vehicles/linovind/mig/oudithero/fes.png)
Fig. 74: Pressing In Rear Spring Leaf Bush
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
INSTALLATION
HINT:
Use the same procedures for the RH side and LH side.
The procedures listed below are for the LH side.
A bolt without a torque specification is shown in the standard bolt chart (see SPECIFIED TORQUE
FOR STANDARD BOLTS ).
1. INSTALL REAR SPRING SHACKLE BUSH
a. Install the 2 shackle bushes to the frame.
Fig. 75: Locating Rear Spring Shackle Bush
2009 Toyota Tundra
2009 SUSPENSION Suspension - Tundra
![](/vehicles/linovind/mig/oudithero/wam.png)
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
2. INSTALL TUBE
a. Install the tube to the bush.
Fig. 76: Locating Tube
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
3. TEMPORARILY INSTALL REAR SPRING ASSEMBLY LH
a. Temporarily install the spring with the No. 2 spring shackle plate, shackle outer plate, 2 washers
and 2 nuts to the rear side.
Fig. 77: Locating No. 2 Spring Shackle Plate And Bolts
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
b. Temporarily install the spring with the bolt, washer and nut to the front side.
Fig. 78: Locating Rear Spring Bolt
2009 Toyota Tundra
2009 SUSPENSION Suspension - Tundra
![](/vehicles/linovind/mig/oudithero/fto.png)
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
4. INSTALL REAR SPRING BUMPER SUB-ASSEMBLY
a. Install the spring bumper.
Fig. 79: Locating Leaf Spring Center Bolt And Nut
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
5. TEMPORARILY INSTALL REAR SPRING U BOLT
a. Temporarily install the spring seat and 2 U bolts with the 4 washers and 4 nuts.
6. CONNECT N0. 3 PARKING BRAKE CABLE ASSEMBLY
a. Connect the parking brake cable to the vehicle with the 3 bolts.
Torque: for Bolt A
NOTE:
Align the leaf spring center bolt and nut with the installation hole of
the rear axle housing and spring bumper so that they are not loose.
NOTE:
Tighten the nuts in the order shown in the illustration.
Install the U bolts so that the lengths of the 4 ends under the
spring seat are the same.
Fig. 80: Identifying Rear Spring U Bolt Tightening Sequence
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
2009 Toyota Tundra
2009 SUSPENSION Suspension - Tundra
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст