Toyota Tundra. Manual — part 2326
Fig. 124: Identifying Water Bypass Hose With Bolts
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
24
INSTALL OIL PRESSURE SENDER GAUGE ASSEMBLY (see INSTALLATION )
25
INSTALL OIL FILTER ELEMENT (see REPLACEMENT )
26
CONNECT NO. 2 FUEL TUBE SUB-ASSEMBLY
a
Connect the fuel tube with the 2 bolts
Torque: 10 N*m (102 kgf*cm, 7 ft.*lbf)
2009 Toyota Tundra
2009 ENGINE Lubrication (3UR-FE) - Tundra
Fig. 125: Identifying Fuel Tube Bolts
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
27
CONNECT COOLER COMPRESSOR ASSEMBLY
a
Install the cooler compressor with the 2 stud bolts
Torque: 10 N*m (102 kgf*cm, 7 ft.*lbf)
Fig. 126: Identifying Cooler Compressor With Stud Bolts
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
b
Install the 2 bolts and 2 nuts
Torque: 25 N*m (250 kgf*cm, 18 ft.*lbf)
NOTE:
Tighten the bolts and nuts in the order shown in the illustration to
2009 Toyota Tundra
2009 ENGINE Lubrication (3UR-FE) - Tundra
28
CONNECT HEATER HOSE AND PIPE
a
Connect the 3 hoses
b
Install the 2 bolts
Torque: 10 N*m (102 kgf*cm, 7 ft.*lbf)
Fig. 127: Identifying Hoses And Bolts
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
29
CONNECT AIR PUMP HOSE AND WIRE HARNESS
a
Connect the No 2 and No 3 air hoses
b
Connect the 2 clamps and air pump wire harness
30
INSTALL INTAKE MANIFOLD
a
Install the intake manifold (see INSTALLATION )
Fig. 128: Identifying Intake Manifold No. 2 And No. 3 Air Hoses
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
31
CONNECT ENGINE WIRE
a
Engine Room RH Side:
1
Connect the 5 clamps
2
Connect the throttle position sensor and throttle control motor connector
install the cooler compressor.
2009 Toyota Tundra
2009 ENGINE Lubrication (3UR-FE) - Tundra
3
Connect the 2 air pump connectors
4
Install the ground wire with the 2 bolts
Torque: 8.0 N*m (82 kgf*cm, 71 in.*lbf)
5
Connect the noise filter connector
6
Connect the 2 VVT sensor connectors
7
Connect the injector connector
8
Connect the 4 ignition coil connectors
9
Connect the 2 camshaft timing oil control valve connectors
Fig. 129: Identifying Ignition Coil Connectors And VVT Sensor Connectors
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
10
Connect the 2 clamps and power steering oil pressure switch connector
11
for 4WD:
Connect the clamp and junction connector
Fig. 130: Identifying Clamp And Junction Connector
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
2009 Toyota Tundra
2009 ENGINE Lubrication (3UR-FE) - Tundra
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст