Toyota Tundra. Manual — part 2258

Fig. 404: Locating Engine Wire, Clamps And Oil Pressure Sender Gauge Connectors
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.

3. Connect the throttle sensor connector.

4. Connect the noise filter connector.

5. Connect the fuel injector connector.

6. Connect the 2 VVT sensor connectors.

7. Connect the 4 ignition coil connectors.

8. Connect the 2 camshaft timing control valve connectors.

d. Engine LH Side:

1. Connect the 7 clamps and install the engine wire with the bolt.

Torque: 20 N*m (204 kgf*cm, 15 ft.*lbf)

Fig. 405: Locating Engine Wire, Clamps And Engine Coolant Temperature Sensor
Connectors

Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.

2. Connect the noise filter connector.

3. Connect the fuel injector connector.

2009 Toyota Tundra

2009 ENGINE Engine Mechanical (3UR-FBE) - Tundra

4. Connect the engine coolant temperature sensor connector.

5. Connect the purge VSV connector.

6. Connect the vacuum switching valve connector (for ACIS).

7. Connect the camshaft position sensor connector.

8. Connect the 2 VVT sensor connectors.

9. Connect the 4 ignition coil connectors.

10. Connect the 2 camshaft timing control valve connector.

FRONT ENGINE MOUNTING

COMPONENTS

Fig. 406: Identifying Front Engine Mounting Components With Torque Specifications
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.

REMOVAL

1. REMOVE ENGINE ASSEMBLY

a. Remove the engine assembly from the vehicle (See REMOVAL ).

2. REMOVE FRONT ENGINE MOUNTING INSULATOR RH

a. Remove the nut and mounting insulator.

Fig. 407: Locating Front Engine Mounting Insulator With Nut - RH
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.

2009 Toyota Tundra

2009 ENGINE Engine Mechanical (3UR-FBE) - Tundra

3. REMOVE WATER DRAIN COCK SUB-ASSEMBLY

a. Remove the drain cock from the cylinder block LH side.

Fig. 408: Locating Drain Cock
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.

4. REMOVE FRONT ENGINE MOUNTING INSULATOR LH

a. Remove the nut and mounting insulator.

Fig. 409: Locating Front Engine Mounting Insulator With Mounting Nut - LH
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.

INSTALLATION

1. INSTALL FRONT ENGINE MOUNTING INSULATOR LH

a. Install the mounting insulator with the nut.

Torque: 72 N*m (734 kgf*cm, 53 ft.*lbf)

2009 Toyota Tundra

2009 ENGINE Engine Mechanical (3UR-FBE) - Tundra

Fig. 410: Locating Mounting Insulator With Nut
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.

2. INSTALL WATER DRAIN COCK SUB-ASSEMBLY

a. Apply seal packing to 2 or 3 threads of the drain cock.

Seal packing:

Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent

Fig. 411: Applying Seal Packing To Drain Cock Threads
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.

b. Install the drain cock to the cylinder block LH side.

Torque: 30 N*m (306 kgf*cm, 22 ft.*lbf)

2009 Toyota Tundra

2009 ENGINE Engine Mechanical (3UR-FBE) - Tundra

Была ли эта страница вам полезна?
Да!Нет
8 посетителей считают эту страницу полезной.
Большое спасибо!
Ваше мнение очень важно для нас.

Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.

Текст

Политика конфиденциальности