Toyota Highlander (2018 year). Manual — part 21
96
2. Instrument cluster
■
Operating the meter control switches
Enter/Set/Reset
Select an item/change pages
Return to the previous
screen
Press: Displays the screen
registered as the top screen
When no screen has been regis-
tered, the drive information
screen will be displayed.
Press and hold: Registers the currently displayed screen as the
top screen
When the confirmation screen is displayed, select yes to register the
screen. If the selected screen cannot be registered, a registration failure
message will be shown.
1
2
3
4
97
2. Instrument cluster
2
Instrum
e
nt clus
ter
● Current fuel consumption
*
1
Displays the current rate of fuel consumption
● Average fuel economy (after reset
*
2
/after start/after refuel)
*
1
Displays the average fuel economy since the function was reset,
the engine was started, and the vehicle was refueled, respectively
Use the displayed average fuel economy as a reference.
● Average vehicle speed (after reset
*
2
/after start)
*
1
Displays the average vehicle speed since the function was reset
and the engine was started, respectively
● Elapsed time (after reset
*
2
/after start)
*
1
Displays the elapsed time since the function was reset and the
engine was started, respectively
● Distance (driving range/after start/after reset
*
2
)
*
1
Displays the estimated maximum distance that can be driven with
the quantity of fuel remaining and the distance driven after the
engine was started, respectively.
• This distance is computed based on your average fuel consumption. As
a result, the actual distance that can be driven may differ from that dis-
played.
• When only a small amount of fuel is added to the tank, the display may
not be updated.
When refueling, turn the engine switch off. If the vehicle is refueled with-
out turning the engine switch off, the display may not be updated.
● Eco Driving Indicator
● AWD control (if equipped)
Displays the torque distribution between the front and rear axles of
the AWD control system
● Display off
A blank screen is displayed
*
1
: Can be registered to Drive information 1 through 3. (
*
2
: Resetting procedures:
• Select a function to be reset using the meter control switches and then
press and hold to reset.
• If there is more than one function that can be reset, check boxes will be
displayed next to those functions.
Drive information
98
2. Instrument cluster
■
Stop & Start system operation time (current)/status notification
Displays the current amount of time the engine has been stopped
due to the operation of the Stop & Start system. Also shows the sta-
tus of the Stop & Start system with a pop-up display. (
■
Stop & Start system operation time (after start/after reset)
Displays the accumulated total of the following:
• Stop & Start system operation time since engine start
• Stop & Start system operation time since display was reset
■
Stop & Start system settings
Press the center button of the meter control switches to display the
Stop & Start system settings screen.
On this screen, the following operations can be performed:
● Stop & Start
The length of time the Stop & Start system will operate when the “A/C”
switch of the air conditioning system is on can be set to 2 different lev-
els. This setting can also be changed on
.
● Reset
Select to reset the Stop & Start system operation time display.
To reset, move the cursor to “Reset”, and then press and hold the center
button.
Stop & Start system information (if equipped)
99
2. Instrument cluster
2
Instrum
e
nt clus
ter
Select
using the meter control switches.
Select an item and then set it with the center button.
■
LDA (Lane Departure Alert with steering control) settings
→P. 683
■
PCS (Pre-Collision System) settings
→P. 683
■
BSM (Blind Spot Monitor) settings (if equipped)
Select to activate/deactivate the BSM (Blind Spot Monitor).
(
■
Power mode (driving mode) settings (if equipped)
Select to activate/deactivate the power mode. (
■
Stop & Start system settings (if equipped)
The length of time the Stop & Start system will operate when the “A/
C” switch of the air conditioning system is on can be set to 2 differ-
ent levels. (
■
Meter settings
● Language
Select to change the language on the display.
● Units
Select to change the unit of measure for fuel consumption.
● Maintenance system (for U.S.A.)
Select to reset the maintenance data after the required mainte-
nance is performed. (
→
● Eco Driving Indicator Light
Select to activate/deactivate the Eco Driving Indicator Light.
(
●
switch settings
You can register 1 screen as the top screen. To register, press
and hold
while the desired screen is displayed.
● Drive information 1 through 3
Select to select up to 2 items that will be displayed on a Drive
information screen, up to 3 Drive information screens can be set.
Settings display
1
2
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст