Nissan Pathfinder (2005 year). Manual — part 194
DTC P1031, P1032, P1051, P1052 A/F SENSOR 1 HEATER
EC-403
C
D
E
F
G
H
I
J
K
L
M
A
EC
2005 Pathfinder
BANK 2
BBWA1733E
EC-404
DTC P1031, P1032, P1051, P1052 A/F SENSOR 1 HEATER
2005 Pathfinder
Specification data are reference values and are measured between each terminal and ground.
Pulse signal is measured by CONSULT-II.
CAUTION:
Do not use ECM ground terminals when measuring input/output voltage. Doing so may result in dam-
age to the ECM's transistor. Use a ground other than ECM terminals, such as the ground.
: Average voltage for pulse signal (Actual pulse signal can be confirmed by oscilloscope.)
Diagnostic Procedure
UBS00KBL
1.
CHECK GROUND CONNECTIONS
1.
Turn ignition switch OFF.
2.
Loosen and retighten three ground screws on the body. Refer to
.
OK or NG
OK
>> GO TO 2.
NG
>> Repair or Replace ground connections.
TERMI-
NAL
NO.
WIRE
COLOR
ITEM
CONDITION
DATA (DC Voltage)
24
G
A/F sensor 1 heater
(Bank 2)
[Engine is running]
●
Warm-up condition
●
Idle speed
Approximately 5V
PBIB1584E
BBIA0539E
DTC P1031, P1032, P1051, P1052 A/F SENSOR 1 HEATER
EC-405
C
D
E
F
G
H
I
J
K
L
M
A
EC
2005 Pathfinder
2.
CHECK AIR FUEL RATIO (A/F) SENSOR 1 POWER SUPPLY CIRCUIT
1.
Disconnect air fuel ratio (A/F) sensor 1 harness connector.
2.
Turn ignition switch ON.
3.
Check voltage between air fuel ratio sensor 1 terminal 3 and
ground with CONSULT-II or tester.
OK or NG
OK
>> GO TO 4.
NG
>> GO TO 3.
3.
DETECT MALFUNCTIONING PART
Check the following.
●
Harness connectors E5, F14
●
IPDM E/R harness connector E119
●
10A fuse
●
Harness for open or short between air fuel ratio sensor 1 and fuse
>> Repair or replace harness or connectors.
4.
CHECK AIR FUEL RATIO (A/F) SENSOR 1 HEATER OUTPUT SIGNAL CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect ECM harness connector.
3.
Check harness continuity between ECM terminal 2 (bank 1) or 24 (bank 2) and air fuel ratio (A/F) sensor
1 terminal 4.
Refer to Wiring Diagram.
4.
Also check harness for short to ground or short to power.
OK or NG
OK
>> GO TO 5.
NG
>> Repair open circuit or short to ground or short to power in harness or connectors.
Voltage: Battery voltage
BBIA0544E
PBIB1683E
Continuity should exist.
EC-406
DTC P1031, P1032, P1051, P1052 A/F SENSOR 1 HEATER
2005 Pathfinder
5.
CHECK AIR FUEL RATIO (A/F) SENSOR 1 HEATER
Refer to
EC-406, "Component Inspection"
.
OK or NG
OK
>> GO TO 6.
NG
>> GO TO 7.
6.
CHECK INTERMITTENT INCIDENT
Perform
EC-158, "TROUBLE DIAGNOSIS FOR INTERMITTENT INCIDENT"
.
OK or NG
OK
>> GO TO 7.
NG
>> Repair or replace.
7.
REPLACE AIR FUEL RATIO (A/F) SENSOR 1
Replace air fuel ratio (A/F) sensor 1.
CAUTION:
●
Discard any air fuel ratio (A/F) sensor which has been dropped from a height of more than 0.5 m
(19.7 in) onto a hard surface such as a concrete floor; use a new one.
●
Before installing new air fuel ratio (A/F) sensor, clean exhaust system threads using Heated Oxy-
gen Sensor Thread Cleaner tool J-43897-18 or J-43897-12 and approved anti-seize lubricant.
>> INSPECTION END
Component Inspection
UBS00KBM
AIR FUEL RATIO (A/F) SENSOR 1 HEATER
Check resistance between terminals 3 and 4.
Check continuity between terminals 3 and 1, 2, 5, 6, terminals 4 and
1, 2, 5, 6.
If NG, replace the air fuel ratio (A/F) sensor 1.
CAUTION:
●
Discard any air fuel ratio (A/F) sensor which has been
dropped from a height of more than 0.5 m (19.7 in) onto a
hard surface such as a concrete floor; use a new one.
●
Before installing new air fuel ratio (A/F) sensor, clean
exhaust system threads using Heated Oxygen Sensor
Thread Cleaner tool J-43897-18 or J-43897-12 and approved
anti-seize lubricant.
Removal and Installation
UBS00KBN
AIR FUEL RATIO (A/F) SENSOR 1
Refer to
EM-21, "EXHAUST MANIFOLD AND THREE WAY CATALYST"
.
Resistance: 2.3 - 4.3
Ω
at 25
°
C (77
°
F)
Continuity should not exist.
PBIB1684E
DTC P1065 ECM POWER SUPPLY
EC-407
C
D
E
F
G
H
I
J
K
L
M
A
EC
2005 Pathfinder
DTC P1065 ECM POWER SUPPLY
PFP:23710
Component Description
UBS00KBO
Battery voltage is supplied to the ECM even when the ignition switch
is turned OFF for the ECM memory function of the DTC memory, the
air-fuel ratio feedback compensation value memory, the idle air vol-
ume learning value memory, etc.
On Board Diagnosis Logic
UBS00KBP
DTC Confirmation Procedure
UBS00KBQ
NOTE:
If DTC Confirmation Procedure has been previously conducted, always turn ignition switch OFF and wait at
least 10 seconds before conducting the next test.
WITH CONSULT-II
1.
Turn ignition switch ON and wait at least 1 second.
2.
Select “DATA MONITOR” mode with CONSULT-II.
3.
Start engine and let it idle for 1 second.
4.
Turn ignition switch OFF, wait at least 10 seconds, and then turn
ON.
5.
Repeat steps 3 and 4 for 4 times.
6.
If 1st trip DTC is detected, go to
EC-409, "Diagnostic Procedure"
.
WITH GST
Follow the procedure “WITH CONSULT-II” above.
PBIB1164E
DTC No.
Trouble diagnosis name
DTC detecting condition
Possible cause
P1065
1065
ECM power supply cir-
cuit
ECM back-up RAM system does not function
properly.
●
Harness or connectors
[ECM power supply (back-up) circuit is
open or shorted.]
●
ECM
SEF058Y
EC-408
DTC P1065 ECM POWER SUPPLY
2005 Pathfinder
Wiring Diagram
UBS00KBR
BBWA1758E
DTC P1065 ECM POWER SUPPLY
EC-409
C
D
E
F
G
H
I
J
K
L
M
A
EC
2005 Pathfinder
Specification data are reference values and are measured between each terminal and ground.
CAUTION:
Do not use ECM ground terminals when measuring input/output voltage. Doing so may result in dam-
age to the ECM's transistor. Use a ground other than ECM terminals, such as the ground.
Diagnostic Procedure
UBS00KBS
1.
CHECK ECM POWER SUPPLY
1.
Turn ignition switch OFF.
2.
Disconnect ECM harness connector.
3.
Check voltage between ECM terminal 121 and ground with
CONSULT-II or tester.
OK or NG
OK
>> GO TO 3.
NG
>> GO TO 2.
2.
DETECT MALFUNCTIONING PART
Check the following.
●
20A fuse
●
IPDM E/R harness connector E121
●
Harness for open or short between ECM and IPDM E/R
>> Repair open circuit in harness or connectors.
3.
CHECK INTERMITTENT INCIDENT
Refer to
EC-158, "TROUBLE DIAGNOSIS FOR INTERMITTENT INCIDENT"
.
OK or NG
OK
>> GO TO 4.
NG
>> Repair or replace harness or connectors.
TER-
MINAL
NO.
WIRE
COLOR
ITEM
CONDITION
DATA (DC Voltage)
121
R/B
Power supply for ECM
(Back-up)
[Ignition switch: OFF]
BATTERY VOLTAGE
(11 - 14V)
Voltage: Battery voltage
MBIB0026E
EC-410
DTC P1065 ECM POWER SUPPLY
2005 Pathfinder
4.
PERFORM DTC CONFIRMATION PROCEDURE
With CONSULT-II
1.
Turn ignition switch ON.
2.
Select “SELF DIAG RESULTS” mode with CONSULT-II.
3.
Touch “ERASE”.
4.
Perform DTC Confirmation Procedure.
See
.
5.
Is the 1st trip DTC P1065 displayed again?
With GST
1.
Turn ignition switch ON.
2.
Select Service $04 with GST.
3.
Touch “ERASE”.
4.
Perform DTC Confirmation Procedure.
See
.
5.
Is the 1st trip DTC P1065 displayed again?
Yes or No
Yes
>> GO TO 5.
No
>> INSPECTION END
5.
REPLACE ECM
1.
Replace ECM.
2.
Perform initialization of NVIS(NATS) system and registration of all NVIS(NATS) ignition key IDs. Refer to
BL-101, "ECM Re-communicating Function"
.
3.
Perform
.
4.
Perform
EC-88, "Accelerator Pedal Released Position Learning"
.
5.
Perform
EC-88, "Throttle Valve Closed Position Learning"
.
6.
Perform
EC-89, "Idle Air Volume Learning"
.
>> INSPECTION END

Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст