Nissan Pathfinder (2005 year). Manual — part 27
TROUBLE DIAGNOSIS FOR SYMPTOMS
AT-187
D
E
F
G
H
I
J
K
L
M
A
B
AT
2005 Pathfinder
Large Shock (“N” to “D” Position)
UCS0037M
SYMPTOM:
A noticeable shock occurs when the selector lever is shifted from the “N” to “D” position.
DIAGNOSTIC PROCEDURE
1.
CHECK SELF-DIAGNOSTIC RESULTS
Perform self-diagnosis. Refer to
AT-87, "SELF-DIAGNOSTIC RESULT MODE"
.
Is any malfunction detected by self-diagnostic results?
YES
>> Check the malfunctioning system. Refer to
AT-87, "SELF-DIAGNOSTIC RESULT MODE"
.
NO
>> GO TO 2.
2.
ENGINE IDLE SPEED
Check the engine idle speed. Refer to
EC-76, "Idle Speed and Ignition Timing Check"
.
OK or NG
OK
>> GO TO 3.
NG
>> Repair.
3.
CHECK CONTROL CABLE
Check the control cable.
●
Refer to
AT-222, "Checking of A/T Position"
.
OK or NG
OK
>> GO TO 4.
NG
>> Adjust control cable. Refer to
AT-222, "Adjustment of A/T Position"
.
4.
CHECK A/T FLUID LEVEL
Check the A/T fluid level. Refer to
.
OK or NG
OK
>> GO TO 5.
NG
>> Refill ATF.
5.
CHECK LINE PRESSURE
Check line pressure at idle with selector lever in “D” position. Refer to
.
OK or NG
OK
>> GO TO 8.
NG - 1 >> Line pressure high: GO TO 6.
NG - 2 >> Line pressure low: GO TO 7.
6.
DETECT MALFUNCTIONING ITEM
1.
Check control valve with TCM. Refer to
AT-233, "Control Valve With TCM and A/T Fluid Temperature Sen-
.
2.
Disassemble A/T. Refer to
.
3.
Check the following.
–
Oil pump assembly. Refer to
.
OK or NG
OK
>> GO TO 8.
NG
>> Repair or replace damaged parts.
AT-188
TROUBLE DIAGNOSIS FOR SYMPTOMS
2005 Pathfinder
7.
DETECT MALFUNCTIONING ITEM
1.
Check control valve with TCM. Refer to
AT-233, "Control Valve With TCM and A/T Fluid Temperature Sen-
.
2.
Disassemble A/T. Refer to
.
3.
Check the following.
–
Oil pump assembly. Refer to
.
–
Power train system. Refer to
.
–
Transmission case. Refer to
.
OK or NG
OK
>> GO TO 8.
NG
>> Repair or replace damaged parts.
8.
CHECK A/T FLUID CONDITION
1.
Remove oil pan. Refer to
AT-233, "Control Valve With TCM and A/T Fluid Temperature Sensor 2"
.
2.
Check A/T fluid condition. Refer to
AT-50, "Fluid Condition Check"
.
OK or NG
OK
>> GO TO 10.
NG
>> GO TO 9.
9.
DETECT MALFUNCTIONING ITEM
●
Check the malfunction items. If any items are damaged, repair or replace damaged parts. Refer to
(Symptom No.1).
OK or NG
OK
>> GO TO 10.
NG
>> Repair or replace damaged parts.
10.
CHECK SYMPTOM
Check again. Refer to
.
OK or NG
OK
>> INSPECTION END
NG
>> GO TO 11.
11.
PERFORM TCM INSPECTION
1.
Perform TCM input/output signals inspection. Refer to
AT-83, "TCM Input/Output Signal Reference Val-
.
2.
If NG, recheck A/T assembly harness connector terminals for damage or loose connection with harness
connector.
OK or NG
OK
>> INSPECTION END
NG
>> Repair or replace damaged parts.
TROUBLE DIAGNOSIS FOR SYMPTOMS
AT-189
D
E
F
G
H
I
J
K
L
M
A
B
AT
2005 Pathfinder
Vehicle Does Not Creep Backward In “R” Position
UCS0037N
SYMPTOM:
The vehicle does not creep in the “R” position. Or an extreme lack of acceleration is observed.
DIAGNOSTIC PROCEDURE
1.
CHECK SELF-DIAGNOSTIC RESULTS
Perform self-diagnosis. Refer to
AT-87, "SELF-DIAGNOSTIC RESULT MODE"
.
Is any malfunction detected by self-diagnostic results?
YES
>> Check the malfunctioning system. Refer to
AT-87, "SELF-DIAGNOSTIC RESULT MODE"
.
NO
>> GO TO 2.
2.
CHECK CONTROL CABLE
Check the control cable.
●
Refer to
AT-222, "Checking of A/T Position"
.
OK or NG
OK
>> GO TO 3.
NG
>> Adjust control cable. Refer to
AT-222, "Adjustment of A/T Position"
.
3.
CHECK A/T FLUID LEVEL
Check A/T fluid level. Refer to
.
OK or NG
OK
>> GO TO 4.
NG
>> Refill ATF.
4.
CHECK STALL TEST
Check stall revolution with selector lever in “1” and “R” positions.
Refer to
.
OK or NG
OK
>> GO TO 6.
OK in “1” position, NG in “R” position>>GO TO 5.
NG in both “1” and “R” positions>>GO TO 8.
5.
DETECT MALFUNCTIONING ITEM
1.
Disassemble A/T. Refer to
.
2.
Check the following items:
–
Reverse brake. Refer to
.
OK or NG
OK
>> GO TO 9.
NG
>> Repair or replace damaged parts.
6.
CHECK LINE PRESSURE
Check the line pressure with the engine idling. Refer to
.
OK or NG
OK
>> GO TO 9.
NG - 1 >> Line pressure high. GO TO 7.
NG - 2 >> Line pressure low. GO TO 8.
AT-190
TROUBLE DIAGNOSIS FOR SYMPTOMS
2005 Pathfinder
7.
DETECT MALFUNCTIONING ITEM
1.
Check control valve with TCM. Refer to
AT-233, "Control Valve With TCM and A/T Fluid Temperature Sen-
.
2.
Disassemble A/T. Refer to
.
3.
Check the following.
–
Oil pump assembly. Refer to
.
OK or NG
OK
>> GO TO 9.
NG
>> Repair or replace damaged parts.
8.
DETECT MALFUNCTIONING ITEM
1.
Check control valve with TCM. Refer to
AT-233, "Control Valve With TCM and A/T Fluid Temperature Sen-
.
2.
Disassemble A/T. Refer to
.
3.
Check the following.
–
Oil pump assembly. Refer to
.
–
Power train system. Refer to
.
–
Transmission case. Refer to
.
OK or NG
OK
>> GO TO 9.
NG
>> Repair or replace damaged parts.
9.
CHECK A/T FLUID CONDITION
1.
Remove oil pan. Refer to
AT-233, "Control Valve With TCM and A/T Fluid Temperature Sensor 2"
.
2.
Check A/T fluid condition. Refer to
AT-50, "Fluid Condition Check"
.
OK or NG
OK
>> GO TO 10.
NG
>> GO TO 13.
10.
DETECT MALFUNCTIONING ITEM
●
Check the malfunction items. If any items are damaged, repair or replace damaged parts. Refer to
(Symptom No.43).
OK or NG
OK
>> GO TO 11.
NG
>> Repair or replace damaged parts.
11.
CHECK SYMPTOM
Check again. Refer to
.
OK or NG
OK
>> INSPECTION END
NG
>> GO TO 12.
12.
PERFORM TCM INSPECTION
1.
Perform TCM input/output signals inspection. Refer to
AT-83, "TCM Input/Output Signal Reference Val-
.
2.
If NG, recheck A/T assembly harness connector terminals for damage or loose connection with harness
connector.
OK or NG
OK
>> INSPECTION END
NG
>> Repair or replace damaged parts.
TROUBLE DIAGNOSIS FOR SYMPTOMS
AT-191
D
E
F
G
H
I
J
K
L
M
A
B
AT
2005 Pathfinder
13.
DETECT MALFUNCTIONING ITEM
●
Check the malfunction items. If any items are damaged, repair or replace damaged parts. Refer to
(Symptom No.43).
OK or NG
OK
>> GO TO 11.
NG
>> Repair or replace damaged parts.
AT-192
TROUBLE DIAGNOSIS FOR SYMPTOMS
2005 Pathfinder
Vehicle Does Not Creep Forward In “D” Position
UCS0037O
SYMPTOM:
Vehicle does not creep forward when selecting “D” position.
DIAGNOSTIC PROCEDURE
1.
CHECK SELF-DIAGNOSTIC RESULTS
Perform self-diagnosis. Refer to
AT-87, "SELF-DIAGNOSTIC RESULT MODE"
.
Is any malfunction detected by self-diagnostic results?
YES
>> Check the malfunctioning system. Refer to
AT-87, "SELF-DIAGNOSTIC RESULT MODE"
.
NO
>> GO TO 2.
2.
CHECK CONTROL CABLE
Check the control cable.
●
Refer to
AT-222, "Checking of A/T Position"
.
OK or NG
OK
>> GO TO 3.
NG
>> Adjust control cable. Refer to
AT-222, "Adjustment of A/T Position"
.
3.
CHECK A/T FLUID LEVEL
Check A/T fluid level. Refer to
.
OK or NG
OK
>> GO TO 4.
NG
>> Refill ATF.
4.
CHECK STALL TEST
Check stall revolution with selector lever in “D” position. Refer to
.
OK or NG
OK
>> GO TO 5.
NG
>> GO TO 7.
5.
CHECK LINE PRESSURE
Check line pressure at idle with selector lever in “D” position. Refer to
.
OK or NG
OK
>> GO TO 8.
NG - 1 >> Line pressure high. GO TO 6.
NG - 2 >> Line pressure low. GO TO 7.
6.
DETECT MALFUNCTIONING ITEM
1.
Check control valve with TCM. Refer to
AT-233, "Control Valve With TCM and A/T Fluid Temperature Sen-
.
2.
Disassemble A/T. Refer to
.
3.
Check the following items:
–
Oil pump assembly. Refer to
.
OK or NG
OK
>> GO TO 8.
NG
>> Repair or replace damaged parts.
TROUBLE DIAGNOSIS FOR SYMPTOMS
AT-193
D
E
F
G
H
I
J
K
L
M
A
B
AT
2005 Pathfinder
7.
DETECT MALFUNCTIONING ITEM
1.
Check control valve with TCM. Refer to
AT-233, "Control Valve With TCM and A/T Fluid Temperature Sen-
.
2.
Disassemble A/T. Refer to
.
3.
Check the following.
–
Oil pump assembly. Refer to
.
–
Power train system. Refer to
.
–
Transmission case. Refer to
.
OK or NG
OK
>> GO TO 8.
NG
>> Repair or replace damaged parts.
8.
CHECK A/T FLUID CONDITION
1.
Remove oil pan. Refer to
AT-233, "Control Valve With TCM and A/T Fluid Temperature Sensor 2"
.
2.
Check A/T fluid condition. Refer to
AT-50, "Fluid Condition Check"
.
OK or NG
OK
>> GO TO 9.
NG
>> GO TO 12.
9.
DETECT MALFUNCTIONING ITEM
●
Check the malfunction items. If any items are damaged, repair or replace damaged parts. Refer to
(Symptom No.43).
OK or NG
OK
>> GO TO 10.
NG
>> Repair or replace damaged parts.
10.
CHECK SYMPTOM
Check again. Refer to
.
OK or NG
OK
>> INSPECTION END
NG
>> GO TO 11.
11.
PERFORM TCM INSPECTION
1.
Perform TCM input/output signals inspection. Refer to
AT-83, "TCM Input/Output Signal Reference Val-
.
2.
If NG, recheck A/T assembly harness connector terminals for damage or loose connection with harness
connector.
OK or NG
OK
>> INSPECTION END
NG
>> Repair or replace damaged parts.
12.
DETECT MALFUNCTIONING ITEM
●
Check the malfunction items. If any items are damaged, repair or replace damaged parts. Refer to
(Symptom No.43).
OK or NG
OK
>> GO TO 10.
NG
>> Repair or replace damaged parts.
AT-194
TROUBLE DIAGNOSIS FOR SYMPTOMS
2005 Pathfinder
Vehicle Cannot Be Started From D
1
UCS0037P
SYMPTOM:
Vehicle cannot be started from D
1
on cruise test - Part 1.
DIAGNOSTIC PROCEDURE
1.
CONFIRM THE SYMPTOM
Check if vehicle creeps in “R” position.
OK or NG
OK
>> GO TO 2.
NG
>> Refer to
AT-189, "Vehicle Does Not Creep Backward In “R” Position"
.
2.
CHECK SELF-DIAGNOSTIC RESULTS
Perform self-diagnosis. Refer to
AT-87, "SELF-DIAGNOSTIC RESULT MODE"
.
Is any malfunction detected by self-diagnostic results?
YES
>> Check the malfunctioning system. Refer to
AT-87, "SELF-DIAGNOSTIC RESULT MODE"
.
NO
>> GO TO 3.
3.
CHECK ACCELERATOR PEDAL POSITION (APP) SENSOR
Check accelerator pedal position (APP) sensor. Refer to
AT-127, "DTC P1705 THROTTLE POSITION SEN-
.
OK or NG
OK
>> GO TO 4.
NG
>> Repair or replace accelerator pedal position (APP) sensor.
4.
CHECK A/T FLUID LEVEL
Check A/T fluid level. Refer to
.
OK or NG
OK
>> GO TO 5.
NG
>> Refill ATF.
5.
CHECK LINE PRESSURE
Check line pressure at the engine stall point. Refer to
.
OK or NG
OK
>> GO TO 8.
NG - 1 >> Line pressure high. GO TO 6.
NG - 2 >> Line pressure low. GO TO 7.
6.
DETECT MALFUNCTIONING ITEM
1.
Check control valve with TCM. Refer to
AT-233, "Control Valve With TCM and A/T Fluid Temperature Sen-
.
2.
Disassemble A/T. Refer to
.
3.
Check the following.
–
Oil pump assembly. Refer to
.
OK or NG
OK
>> GO TO 8.
NG
>> Repair or replace damaged parts.

Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст