Qashqai J11. Exterior Lighting system — part 21
![](/vehicles/gon/xpitwh/thado/plld.png)
EXL-322
< REMOVAL AND INSTALLATION >
[HALOGEN HEADLAMP]
FRONT FOG LAMP
• Never touch the glass of bulb directly by hand. Keep grease and other oily matters away from it.
• Never touch bulb by hand while it is lit or right after being turned OFF.
• Never leave bulb out of lamp reflector for a long time because dust, moisture smoke, etc. may affect
the performance of lamp. When replacing bulb, be sure to replace it with new one.
FRONT FOG LAMP BULB
1.
Remove fender protector to make work space. Refer to
EXT-32, "Removal and Installation"
.
2.
Disconnect front fog lamp harness connector
.
3.
Rotate front fog lamp bulb
counterclockwise and unlock it.
JPLIA0345ZZ
![](/vehicles/gon/xpitwh/thado/bea.png)
SIDE TURN SIGNAL LAMP
EXL-323
< REMOVAL AND INSTALLATION >
[HALOGEN HEADLAMP]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
SIDE TURN SIGNAL LAMP
Exploded View
INFOID:0000000010437136
.
Removal and Installation
INFOID:0000000010437137
REMOVAL
1.
Remove door mirror cover. Refer to
MIR-31, "Removal and Installation"
.
2.
Remove side turn signal lamp fixing screws.
3.
Remove seal packing
and disconnect side turn signal lamp
harness connector
, and then remove side turn signal lamp
from door mirror housing.
INSTALLATION
Install in the reverse order of removal.
Replacement
INFOID:0000000010437138
CAUTION:
Replacement of a single part is not possible due to the adoption of LED bulb. For replacement, replace
side turn signal lamp as a set.
SIDE TURN SIGNAL LAMP
1.
Remove side turn signal lamp. Refer to
EXL-323, "Removal and Installation"
.
2.
Replace side turn signal lamp with new part.
JMLIA4978ZZ
EXL-324
< REMOVAL AND INSTALLATION >
[HALOGEN HEADLAMP]
LIGHTING & TURN SIGNAL SWITCH
LIGHTING & TURN SIGNAL SWITCH
Removal and Installation
INFOID:0000000010437141
REMOVAL
Remove light & turn signal switch (combination switch). Refer to
BCS-133, "Removal and Installation"
.
INSTALLATION
Install in the reverse order of removal.
![](/vehicles/gon/xpitwh/thado/venk.png)
HAZARD SWITCH
EXL-325
< REMOVAL AND INSTALLATION >
[HALOGEN HEADLAMP]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
HAZARD SWITCH
Exploded View
INFOID:0000000010437142
Removal and Installation
INFOID:0000000010437143
REMOVAL
1.
Remove center ventilator grille. Refer to
IP-13, "Removal and Installation"
.
2.
Disengage fixing pawls, and then remove hazard switch from center ventilator grille.
INSTALLATION
Install in the reverse order of removal.
Center ventilator grille
Hazard switch
: Pawl
JMLIA5094ZZ
![](/vehicles/gon/xpitwh/thado/stho.png)
EXL-326
< REMOVAL AND INSTALLATION >
[HALOGEN HEADLAMP]
HEADLAMP AIMING SWITCH
HEADLAMP AIMING SWITCH
Exploded View
INFOID:0000000010437517
Removal and Installation
INFOID:0000000010437518
REMOVAL
1.
Remove instrument lower panel. Refer to
IP-13, "Removal and Installation"
2.
Remove headlamp aiming switch fixing pawl, and then remove headlamp aiming switch from instrument
lower panel.
INSTALLATION
Install in the reverse order of removal.
Instrument lower panel
Headlamp aiming switch
: Pawl
JMLIA5408ZZ
LIGHT & RAIN SENSOR
EXL-327
< REMOVAL AND INSTALLATION >
[HALOGEN HEADLAMP]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
LIGHT & RAIN SENSOR
Exploded View
INFOID:0000000010437152
Removal and Installation
INFOID:0000000010437153
REMOVAL
Remove light & rain sensor. Refer to
WW-92, "Removal and Installation"
.
INSTALLATION
Install in the reverse order of removal.
![](/vehicles/gon/xpitwh/thado/heta.png)
EXL-328
< REMOVAL AND INSTALLATION >
[HALOGEN HEADLAMP]
REAR COMBINATION LAMP
REAR COMBINATION LAMP
Exploded View
INFOID:0000000010437154
REMOVAL
Body Side
Back Door Side
Grommet A
Grommet B
Rear combination lamp
: Clip
: Clip
: N·m (kg-m, in-lb)
JMLIA5098GB
![](/vehicles/gon/xpitwh/thado/hyod.png)
REAR COMBINATION LAMP
EXL-329
< REMOVAL AND INSTALLATION >
[HALOGEN HEADLAMP]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
DISASSEMBLY
Back door assembly
Rear combination lamp
Grommet
: N·m (kg-m, in-lb)
JMLIA5099GB
![](/vehicles/gon/xpitwh/thado/rorsinea.png)
EXL-330
< REMOVAL AND INSTALLATION >
[HALOGEN HEADLAMP]
REAR COMBINATION LAMP
Removal and Installation
INFOID:0000000010437155
CAUTION:
• Disconnect the battery negative terminal or remove power circuit fuse when performing the opera-
tion for preventing electric leakage. Refer to
EXL-8, "Precautions for Removing Battery Terminal"
.
• When removing, always use a remover tool that is made of plastic.
REMOVAL
Rear Combination Lamp (body side)
1.
Fully open trunk lid.
2.
Remove rear combination lamp mounting bolts
.
Rear combination lamp housing
(back door side)
Seal packing
Rear fog lamp bulb
(driver side only)
Rear fog lamp bulb socket
(driver side only)
Back-up lamp bulb
Back-up lamp bulb socket
Rear turn signal lamp bulb socket
Rear turn signal lamp bulb
Rear combination lamp housing
(body side)
: Vehicle front
: Always replace after every disassembly
JMLIA5407ZZ
JMLIA5137ZZ
![](/vehicles/gon/xpitwh/thado/tiat.png)
REAR COMBINATION LAMP
EXL-331
< REMOVAL AND INSTALLATION >
[HALOGEN HEADLAMP]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
3.
Pull rear combination lamp toward vehicle rear to disengage fix-
ing clips.
4.
Disconnect rear combination lamp harness connectors, and then remove rear combination lamp from
body panel.
Rear Combination Lamp (back door side)
1.
Remove back door inner finisher. Refer to
INT-31, "Removal and Installation"
2.
Remove back door finisher. Refer to
EXT-45, "Removal and Installation"
3.
Remove rear combination lamp mounting nuts
and discon-
nect rear combination lamp harness connectors.
4.
Pull rear combination lamp toward vehicle rear to remove rear combination lamp from back door.
INSTALLATION
Note the following item, and then install in the reverse order of removal.
CAUTION:
Always replace seal packing with new part after every removal.
Replacement
INFOID:0000000010437156
CAUTION:
• Disconnect the battery negative terminal or remove power circuit fuse when performing the opera-
tion for preventing electric leakage. Refer to
EXL-182, "Precautions for Removing Battery Terminal"
.
• Never touch the glass of bulb directly by hand. Keep grease and other oily matters away from it.
• Never touch bulb by hand while it is lit or right after being turned OFF.
• Never leave bulb out of lamp reflector for a long time because dust, moisture smoke, etc. may affect
the performance of lamp. When replacing bulb, be sure to replace it with new one.
REAR TURN SIGNAL LAMP BULB
1.
Remove rear combination lamp (body side). Refer to
EXL-330, "Removal and Installation"
2.
Rotate rear turn signal lamp bulb socket counterclockwise, and then remove rear turn signal lamp bulb
socket.
3.
Remove rear turn signal lamp bulb from rear turn signal lamp bulb socket.
STOP/TAIL LAMP
CAUTION:
Replacement of a single part is not possible due to the adoption of LED bulb. For replacement, replace
rear combination lamp assembly as a set.
REAR FOG LAMP (DRIVER SIDE ONLY)
1.
Remove rear combination lamp (back door side). Refer to
EXL-330, "Removal and Installation"
2.
Rotate rear fog lamp bulb socket counterclockwise, and then remove rear fog lamp bulb socket.
: Clip
JMLIA5138ZZ
JMLIA5139ZZ
EXL-332
< REMOVAL AND INSTALLATION >
[HALOGEN HEADLAMP]
REAR COMBINATION LAMP
3.
Remove rear fog lamp bulb from rear fog lamp bulb socket.
BACK-UP LAMP
1.
Remove rear combination lamp (back door side). Refer to
EXL-330, "Removal and Installation"
2.
Rotate back-up lamp bulb socket counterclockwise, and then remove back-up lamp bulb socket.
3.
Remove back-up lamp bulb from back-up lamp bulb socket.
![](/vehicles/gon/xpitwh/thado/fat.png)
HIGH-MOUNTED STOP LAMP
EXL-333
< REMOVAL AND INSTALLATION >
[HALOGEN HEADLAMP]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
HIGH-MOUNTED STOP LAMP
Exploded View
INFOID:0000000010437157
Removal and Installation
INFOID:0000000010437158
CAUTION:
Disconnect battery negative terminal or remove power circuit fuse when performing the operation for
preventing electric leakage. Refer to
EXL-182, "Precautions for Removing Battery Terminal"
.
REMOVAL
1.
Remove rear spoiler. Refer to
EXT-46, "Removal and Installation"
.
2.
Disengage high-mounted stop lamp fixing metal clips using a remover tool (A), and then remove high-
mounted stop lamp unit.
INSTALLATION
Install in the reverse order of removal.
Replacement
INFOID:0000000010437159
CAUTION:
Replacement of a single part is not possible due to the adoption of LED bulb. For replacement, replace
high-mounted stop lamp unit as a set.
Rear spoiler
High-mounted stop lamp unit
: Metal clip
JMLIA5102ZZ
: Metal clip
JMLIA5136ZZ
![](/vehicles/gon/xpitwh/thado/treethet.png)
EXL-334
< REMOVAL AND INSTALLATION >
[HALOGEN HEADLAMP]
LICENSE PLATE LAMP
LICENSE PLATE LAMP
Exploded View
INFOID:0000000010437160
Removal and Installation
INFOID:0000000010437161
CAUTION:
Disconnect battery negative terminal or remove power circuit fuse when performing the operation for
preventing electric leakage. Refer to
EXL-182, "Precautions for Removing Battery Terminal"
.
REMOVAL.
1.
Remove back door finisher. Refer to
EXT-45, "Removal and Installation"
2.
Disconnect license plate lamp harness connector.
3.
Disengage license plate lamp housing fixing pawl, and then remove license plate lamp housing.
INSTALLATION
Install in the reverse order of removal.
Replacement
INFOID:0000000010437162
CAUTION:
• Disconnect the battery negative terminal or remove power circuit fuse when performing the opera-
tion for preventing electric leakage. Refer to
EXL-182, "Precautions for Removing Battery Terminal"
• Never touch the glass of bulb directly by hand. Keep grease and other oily matters away from it.
• Never touch bulb by hand while it is lit or right after being turned OFF.
Back door panel
Back door finisher
License plate lamp housing
License plate lamp bulb
License plate lamp bulb socket
: Pawl
JMLIA5101ZZ
LICENSE PLATE LAMP
EXL-335
< REMOVAL AND INSTALLATION >
[HALOGEN HEADLAMP]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
• Never leave bulb out of lamp reflector for a long time because dust, moisture smoke, etc. may affect
the performance of lamp. When replacing bulb, be sure to replace it with new one.
LICENSE PLATE LAMP BULB
1.
Remove back door finisher. Refer to
EXT-45, "Removal and Installation"
2.
Rotate the bulb socket counterclockwise and unlock it.
3.
Remove the bulb from the socket.
![](/vehicles/gon/xpitwh/thado/lai.png)
EXL-336
< REMOVAL AND INSTALLATION >
[HALOGEN HEADLAMP]
REAR REFLEX REFLECTOR
REAR REFLEX REFLECTOR
Exploded View
INFOID:0000000010437163
Removal and Installation
INFOID:0000000010437164
REMOVAL
1.
Remove rear bumper fascia. Refer to
EXT-23, "Removal and Installation"
2.
Remove rear reflex reflector mounting bolt and pawls, and then remove rear reflex reflector.
INSTALLATION
Install in the reverse order of removal.
Rear reflex reflector
Rear bumper fascia assembly
: Pawl
JMLIA5103ZZ
![](/vehicles/gon/xpitwh/thado/arob.png)
SERVICE DATA AND SPECIFICATIONS (SDS)
EXL-337
< SERVICE DATA AND SPECIFICATIONS (SDS)
[HALOGEN HEADLAMP]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
Bulb Specifications
INFOID:0000000010437590
Bulb Specifications
Item
Type
Wattage (W)
Front combination lamp
Headlamp (HI)
H11
55
Headlamp (LO)
H7
55
Parking lamp/
daytime running light
LED
—
Front turn signal lamp
W21W
21
Front fog lamp
H8
35
Side turn signal lamp (built in door mirror)
LED
—
Rear combination lamp
(body side)
Tail lamp
LED
—
Stop lamp
LED
—
Rear turn signal lamp
WY21W
21
Rear combination lamp
(trunk lid side)
Tail lamp
LED
—
Back-up lamp
W16W
16
Rear fog lamp (driver side only)
W21W
21
License plate lamp
W5W
5
High-mounted stop lamp
LED
—
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст